Gold Medal Hawaii’s Finest1027 Instruction Manual
Part No.12205
Hawaii’s Finest
WWW.CONCESSIONSTANDS.COM
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
concessionstands.com
Instruction Manual
Model No. 1027
10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA
WWW.CONCESSIONSTANDS.COM
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
concessionstands.com
Ha
waii’s Finest Model No. 1027
SAFETY PRECAUTIONS
Page 2
gmpopcorn.com
WWW.CONCESSIONSTANDS.COM
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
concessionstands.com
Ha
waii’s Finest Model No. 1027
INSTALLATION INSTRUCTIONS
In
spection of Shipment
After unpacking, check thoroughly for any damage which may have occurred in transit. Claims
should be filed immediately with the transportation company. The warranty does not cover
damage that occurs in transit, or damage caused by abuse, or consequential damage due to the
operation of this machine, since it is beyond our control.
Setup
Your new Hawaii’s Finest was completely assembled and tested at the factory. Remove all
packing material and tape before starting operation.
Electrical Requirements
1027: 120V, 840W, 60Hz
DANGER
Machine must be properly grounded to prevent electrical
ock to personnel. Failure to do so could result in serious
sh
injury, or death.
Do NOT immerse any part of this equipment in water.
Do NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from
moisture.
Always unplug the equipment before cleaning or servicing.
Your electrician must furnish sufficient power for proper machine operation. We recommend
is shaver be on a dedicated and protected circuit. Failure to wire properly will void the
th
warranty and may result in damage to the machine. It is Gold Medal Products Company’s
recommendation that this machine be plugged directly into a wall outlet. The use of extension
cords is not recommended due to safety concerns, and may cause sacrificed and/or reduced
performance.
Before You Plug In Machine
1. Make sure all machine switches are in the OFF position before plugging the equipment
into the receptacle.
2. Make sure the wall outlet can accept the grounded plugs (where applicable) on the
power supply cord.
3. The wall outlet must have the proper polarity. If in doubt, have a competent
electrician inspect the outlet and correct if necessary.
4. DO NOT use a grounded to un-grounded receptacle adapter.
5. Make sure to leave enough room in the back of the machine to allow hookup of the
drain hose.
6. Install the unit in a level position.
Page 3
gmpopcorn.com
Main Switch
Reset Switch
Blade Adjustment
WWW.CONCESSIONSTANDS.COM
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
concessionstands.com
Hawaii’s Finest Model No. 1027
OPERATING INSTRUCTIONS
Controls and Their Functions
MAIN SWITCH
Turns shaver motor “ON” or “OFF”.
RESET SWITCH
Motor overload switch.
BLADE ADJUSTMENT KNOB
Adjusts the blade height to change the ice texture.
Ice Requirements
The Hawaii’s Finest can take ice cubes or block ice, if you break the block into pieces
approximately 2 to 3 inches in size.
NOTE: The ice will not enter the shaving chute if the pieces are too large.
Operation of Hawaii’s Finest
1. Allow ice to soften at least 1 hour in an ice cooler before use. Using ice straight from
the freezer affects the quality of the shaved ice as well as damage the shaver blade.
2. Lift cover lid and load ice cubes about ½ full then close the lid. Be sure ice is loaded
evenly in each cavity. Place cup directly below the ice chute and turn power “ON”.
Failure to close the lid will cause machine not to operate!
3. Adjust the blade height with the adjustment knob to achieve the preferred ice texture.
4. To stop, turn power switch to the “OFF” position. Should the motor thermal protector
trip, reset it by pushing the red button. It is recommended the cause of over load be
found and eliminated before continuing. The machine may need to cool a bit before
the reset button may take effect.
NOTE: Never allow any foreign or metallic objects around the shaver area of the Hawaii’s
Finest. Ice picks, scoops, and debris that may be in the ice often damage blades.
Page 4
gmpopcorn.com
WWW.CONCESSIONSTANDS.COM
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
concessionstands.com
Ha
waii’s Finest Model No. 1027
CARE AND CLEANING
Cl
eaning Instructions
1. Remove lid by removing the wing nut and hinge pin.
2. Remove the four plastic button screws that hold top hopper cover, and lift and
roll over.
3. Disconnect wire harness at plug.
4. Remove three thumb screws and remove impeller cover.
5. Remove impeller knob, and lift impeller off. For removal of Impeller Knob a
screwdriver slot is supplied on bottom end of motor.
6. Lift off bottom plastic base cover.
7. Remove two stainless steel button screws holding chute.
8. Wipe down all easily accessible areas with a clean, dry cloth.
Blade Cleaning Instructions
1. Blade holder should be cleaned at weekly intervals. Begin removal by removing chute.
2. Using blade adjustment knob, unscrew blade adjustment shaft and remove.
3. Pull pivot pin out completely.
4. Blade, blade holder assembly and spring are now free for removal.
5. Remove the two blade retaining screws and remove blade.
6. Wipe area and parts with clean, dry cloth.
7. Assemble in opposite order as above.
The stainless steel body of the shaver can be kept clean with cleaner designed for stainless steel
and a clean cloth. We recommend Gold Medal Products Company’s authentic Watchdog Stainless
Steel Polish (Part No. 2088.)
NOTE: Never use abrasives on the stainless steel body.
DANGER
Machine must be properly grounded to prevent electrical
ock to personnel.
sh
DO NOT immerse in water.
Always unplug the equipment before cleaning or servicing.
od sanitation practice demands that all food preparation equipment be cleaned regularly. A
Go
clean looking, well-kept machine is one of the best ways of advertising your product.
Page 5
gmpopcorn.com
Loading...