Gold Medal Econo-Pop 14 Popper, 2121NSX Instruction Manual

Econo

-

Pop 14 Popper

Instruction Manual

Export Model No. 2121NSX

10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA

© 2016 Gold Medal Products Co.

Part No. 110073

cause property damage, injury, or death. Any alterations to this equipment will

Econo-Pop 14 Popper Export Model No. 2121NSX

SAFETY PRECAUTIONS

DANGER

Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle.

DANGER

Improper installation, adjustment, alteration, service, or maintenance can

void the warranty and may cause a dangerous condition. NEVER make
alterations to this equipment. Read the Installation, Operating, and
Maintenance Instructions thoroughly before installing, servicing, or operating
this equipment.

008_051514

014_051514

WARNING

To avoid burns, DO NOT touch the kettle or any heated surface.
DO NOT place or leave objects in contact with heated surfaces.

013_092414

WARNING

ALWAYS wear safety glasses when servicing this equipment.

010_010914

WARNING

No user serviceable parts inside. Refer servicing to qualified service
personnel.

011_051514

WARNING

Read and understand operator’s manual and all other safety instructions
before using this equipment. To order copies of the operator’s manual go to
gmpopcorn.com or write to Gold Medal Products Co., 10700 Medallion Drive,
Cincinnati, OH 45241 USA 1-(800)-543-0862

022_060215

Page 2

gmpopcorn.com

Econo-Pop 14 Popper Export Model No. 2121NSX

SAFETY PRECAUTIONS (continued)

WARNING

DO NOT allow direct contact of this equipment by the public when used in
food service locations. Only personnel trained and experienced in the
equipment operation may operate this equipment.
Carefully read all instructions before operation.

WARNING

This machine is NOT to be operated by minors.

Note: Improvements are always being made to Gold Medal’s equipment. This

information may not be the latest available for your purposes. It is critical that
you call Gold Medal’s Technical Service Department at 1-800-543-0862 for any
questions about your machine operations, replacement parts, or any service
questions. (Gold Medal Products Co. does not assume any liability for injury due
to careless handling and/or reckless operation of this equipment.)

012_010914

007_010914

Page 3

gmpopcorn.com

Bulb for Cabinet

1/2 Cup Oil Measure

Econo-Pop 14 Popper Export Model No. 2121NSX

INSTALLATION INSTRUCTIONS

Inspection of Shipment

After unpacking, check thoroughly for any damage which may have occurred in transit. Claims
should be filed immediately with the transportation company. The warranty does not cover
damage that occurs in transit, or damage caused by abuse, or consequential damage due to the
operation of this machine, since it is beyond our control (reference warranty in back of manual).

Manual

Read and understand the operator’s manual and all other safety instructions before using this
equipment. To order copies of the operator’s manual go to gmpopcorn.com or write to Gold
Medal Products Co., 10700 Medallion Drive, Cincinnati, OH 45241 USA 1-(800)-543-0862.

Model Description

2121NSX: Export 14 oz. Econo-Pop Popper

Items Included with this Unit

Aluminum Scoop

Interior

Measure 14.7 cc

14 oz. Corn Measure

Black Crutch Tips

Page 4

gmpopcorn.com

Econo-Pop 14 Popper Export Model No. 2121NSX

Setup

This unit has been tested at the factory.

1. Remove all packaging and tape prior to operation.

2. Place the unit on a sturdy, level base.

3. The popper unit has 4 glide feet preinstalled at the factory. Install a Black Crutch Tip

on each of the 4 glide feet. Firmly push the crutch tip over the glide until it covers the
glide entirely.

4. The door knobs are shipped facing the inside of the machine. Re-adjust the door knobs

to face the outside of the machine.

5. Carefully install the light bulb (do not over-tighten) into the lamp holder located in the

cabinet interior. Ensure the unit is OFF and unplugged before installing or changing
the bulb (reference the Electrical Requirements section).

6. After setup, the unit should be cleaned prior to use (see Care and Cleaning section of

this manual).

Page 5

gmpopcorn.com

DANGER

Econo-Pop 14 Popper Export Model No. 2121NSX

Electrical Requirements

The following power supply must be provided:

2121NSX: 230 V~, 1420 W, 50 Hz

Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle.

A certified electrician must furnish sufficient power for proper machine operation and install any
supplied receptacle. We recommend this equipment be on a dedicated and protected circuit.
Failure to wire properly will void the warranty and may result in damage to the machine. It is Gold
Medal Products Co.’s recommendation that this machine be plugged directly into a wall outlet. The
use of extension cords is not recommended due to safety concerns, and may cause sacrificed
and/or reduced performance. Make sure cord is located to prevent a trip hazard or unit upset.

008_051514

Before You Plug In Machine

1. Make sure all machine switches are in the OFF position before plugging the equipment

into the receptacle.

2. Make sure the wall outlet can accept the grounded plugs (where applicable) on the

power supply cord.

3. The wall outlet must have the proper polarity. If in doubt, have a competent

electrician inspect the outlet and correct if necessary.

4. DO NOT use a grounded to un-grounded receptacle adapter (where applicable).

5. Install the unit in a level position.

If the supply cord is damaged, it must be replaced by Gold Medal Products Co.,
its service agent or similarly qualified persons in order to avoid a hazard.

CAUTION

039_080614

Page 6

gmpopcorn.com

Light and

Kettle Heat

Kettle Motor

Econo-Pop 14 Popper Export Model No. 2121NSX

OPERATING INSTRUCTIONS

Controls and Their Functions

LIGHTS/WARMER SWITCH

Two position, ON/OFF lighted rocker switch - supplies power to the interior cabinet light
and to the corn pan heat element. The green switch light ON indicates there is power to
the light and corn pan heat element.

KETTLE MOTOR SWITCH

Two position, ON/OFF lighted rocker switch - operates the kettle agitator motor. The
Kettle Motor Switch MUST be ON at all times when there is popcorn (popped or un­popped) in the kettle.

KETTLE HEAT SWITCH

Two position, ON/OFF lighted rocker switch - supplies power to the heating elements in the
popping kettle. The green switch light ON indicates there is power to the kettle heating
element.

Callout

Warmer Switch

Switch

Page 7

Switch

gmpopcorn.com

Kettle

Size

Popcorn

Charge

Oil

Charge

Flavacol (Salt)

14 oz.

14 oz. (414 ml)

4.5 oz. (

133 ml) 1

Tblsp. (

15

cc)

Econo-Pop 14 Popper Export Model No. 2121NSX

Popping Corn

This section describes instructions for popping Standard (salted popcorn).

Your new popper is equipped with a corn, salt, and oil measure. We recommend flavored and
colored coconut oil. Popcorn popped in coconut oil stays fresh longer and does not leave black
deposits in your kettle like other oils. Use only top quality, fresh popcorn from reputable suppliers.

Ingredient amounts for popping Standard Popcorn:

For best results use Mega-Pop® 12 oz. premeasured pouches (Item# 2839).

Popping Standard (Salted) Popcorn

1. Turn the Lights/Warmer, Kettle Heat and Kettle Motor Switches ON.

2. To determine when the kettle is ready to pop corn (about 4 minutes), test pop three

kernels of corn and one ounce (30 ml) of popping oil. When the kernels pop, the kettle
is ready for use.

3. Lift the kettle lid and load the Mega-Pop® premeasured popcorn and oil pouch into

kettle, or pour in the popcorn and Flavacol, then add oil in the premeasured amounts
specified above. Close lid.

4. When the corn has finished popping, gently dump the popcorn.

5. On the final kettle of corn, turn the Kettle Heat Switch OFF just as the lids are forced

open by the popping corn. This procedure saves electricity, since the kettle has plenty
of heat, and helps eliminate smoke/odor from any oil residue that remains after
popping has stopped.

6. When finished popping, make sure KETTLE HEAT and KETTLE MOTOR switches are

turned OFF.

NEVER LEAVE THE HEAT ON WHEN YOU ARE NOT POPPING CORN!

Page 8

gmpopcorn.com

Econo-Pop 14 Popper Export Model No. 2121NSX

Care and Cleaning

DANGER

Machine must be properly grounded to prevent electrical shock to personnel.

DO NOT immerse in water.

Always unplug the equipment before cleaning or servicing.

WARNING

To avoid serious burns, DO NOT touch the kettle while it is hot!

Good sanitation practice demands that all food preparation equipment be cleaned regularly (only
use non-toxic, food grade cleaners). A clean looking, well-kept machine is one of the best ways of
advertising your product.

025_020314

028_082715

Note: It is extremely important to follow all of the cleaning procedures, otherwise parts

damage and equipment failure will result. The warranty does not cover parts that
are damaged due to improper cleaning.

Daily Kettle Cleaning Instructions

CAUTION: A hot kettle will cause burns if you touch it with your hand. Allow kettle to cool

at least 1 hour before attempting to clean. DO NOT use ice or water to cool
down a hot kettle! Severe kettle damage will result!

1. When cool, wipe the outside of the kettle with a clean, soft cloth. DO NOT use oven

cleaners or abrasive materials as they will damage the kettle.

2. Every night, mix Gold Medal’s Heat’n Kleen solution (Item No. 2095), 2 tablespoons

per gallon of water. It is not necessary to use the entire gallon at once; only use
enough to fill the kettle 1/2 inch deep.

3. Turn the kettle heat ON. When the water starts to boil, turn the kettle heat OFF.

4. Allow to cool for at least 1 hour, then dump the solution into a bucket and wipe the

inside of the kettle with a clean cloth. Make sure all of the solution goes into the
bucket; do not spill any in the interior of the machine.

For an extra dirty kettle, the process may be repeated; or, after turning the kettle heat
OFF, allow solution to sit in the kettle overnight. The next morning, dump the solution
into a bucket and wipe the inside of the kettle with a clean cloth.

5. With the unit OFF and unplugged, wipe the kettle lead cord with a clean SLIGHTLY damp

cloth. DO NOT get moisture into the kettle lead-in cord, severe damage will result.

Page 9

gmpopcorn.com

Econo-Pop 14 Popper Export Model No. 2121NSX

Daily Unit Cleaning Instructions

1. With the machine OFF, unplug the unit and allow it to cool before attempting to clean.

2. Make sure to clean all pans/accessories in order to sanitize them before each use.

3. Take a clean, SLIGHTLY damp cloth and wipe excess grease from the glass and cabinet.

4. Wipe the stainless steel parts with a clean cloth and cleaner designed for stainless

steel, such as Gold Medal Watchdog Stainless Cleaner (Item No. 2088).

DO NOT use oven cleaners or abrasive materials as they will damage parts of the
machine.

5. Clean the glass panels with glass cleaner. Gold Medal Watchdog Glass Cleaner (Item

No. 2588) is recommended.

Ammonia cleaners will damage the plastic doors. Use only non-ammonia cleaners,
such as Gold Medal Watchdog Glass Cleaner (Item No. 2588).

Page 10

gmpopcorn.com

Issue

Possible Cause

Solution

Power to the Unit

A. Power to

the

Unit A. Make sure the

unit’s power

cord is plugged in.

Kettle Does Not Heat

A. Power to the Kettle

A. Make sure kettle

lead-in cord is plugged in and

B. Kettle Heat Switch

B. Have a qualified service person c

heck the

C. Heating Element

C. Heating element in

the kettle may

be burned

Long Popping Cycles

A. Low Voltage

A. If the machine is operated on low voltage, this

B. Inadequate Supply Lines

B. Inadequately sized electrical supply lines

or

C. Inferior Corn

C. Inferior quality corn would result in longer

Kettle Agitator Shaft not

A. Kettle Motor Switch

A. If the kettle agitator shaft is not rotating,

B. Kettle Agitator

S

haft

/Stir

B. If the kettle agitator shaft is not rotating,

Econo-Pop 14 Popper Export Model No. 2121NSX

Troubleshooting

twisted to lock into the kettle receptacle.

voltage to and from the Kettle Heat Switch; if
switch is defective, replace it.

out. Check with a qualified service person for
inspection/repair.

(Longer than 4 minutes for
Salt Popcorn)

Rotating

Blade not rotating. (Unit
must be OFF, unplugged
and cool prior to
checking or adjusting
the agitator assembly.)

could cause the kettle not to reach the proper
operating temperature. Check with a qualified
electrician.

use of extension cord, in addition to being a
fire hazard, would also prevent the kettle from
reaching the proper operating temperature.
Check with a qualified electrician.

popping cycles. Use only top quality hybrid
popcorn from reputable suppliers. Even then,
if you let your corn pick up moisture or dry
out, your popping cycles will be slow.

DO NOT pop corn. Make sure the Kettle Motor
Switch is ON. If the switch is ON, and the shaft
is not rotating, the switch or motor may be
faulty, contact qualified service personnel for
inspection/repair.

DO NOT pop corn. Check the clearance
between the kettle bottom and the stir blade;
it should be 1/32” (use a dime). To adjust,
reference the Agitator Set Collar Adjustment
section.

Page 11

gmpopcorn.com

Step 1:

Make sure machine is OFF and

Drive Motor

Agitator’s Spur Gear

Agitator’s Spur Gear

Set Collar

Agitator shown for general image

Set Collar above

Lower Set Collar

Adjust clearance to

Agitator Weight

3/16” to 1/4” max.

Stir Rod

Spur Gear Placement

Crossbar

Econo-Pop 14 Popper Export Model No. 2121NSX

Agitator Set Collar Adjustment

The following instructions describe how to properly adjust set collars on an agitator assembly
with a floating stir rod.

Steps to Adjust Set Collars

unplugged, then allow unit to cool completely
before attempting to adjust the agitator height.

Step 2: Loosen the set screw in each set collar
to be adjusted.

Step 3: With the kettle mounted in the popper,
adjust the shaft so the Agitator’s Spur Gear
contacts half of the Drive Motor Spur Gear
(reference Spur Gear Placement image at right).
DO NOT set spur gears at full gear contact; it
can cause binding as the kettle is dumped.

Step 4: Once shaft is positioned correctly,
re-tighten the set screw in the set collar above
the crossbar to secure in place.

Step 5: Adjust clearance between the bottom of
the crossbar and the lower set collar to 1/32”
(thickness of a dime); then re-tighten set screw
to secure in place (see image below).

Step 6: Adjust set collar for agitator weight to
be between 3/16” to 1/4” above the agitator
weight. Once adjusted, re-tighten set screw to
secure in place.

should set halfway
up on Drive Motor
Spur Gear.

Crossbar

Spur Gear

w/Set screw

reference only (lids not shown for
clarity).

thickness of a dime.

Page 12

(below Crossbar)

Set Collar (for Agitator Weight)

gmpopcorn.com

DANGER

DANGER

cause property damage, injury, or death. Any alterations to this equipment will

WARNING

CAUTION

Econo-Pop 14 Popper Export Model No. 2121NSX

MAINTENANCE INSTRUCTIONS

Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle.

Improper installation, adjustment, alteration, service, or maintenance can

void the warranty and may cause a dangerous condition. NEVER make
alterations to this equipment. Read the Installation, Operating, and
Maintenance Instructions thoroughly before installing, servicing, or operating
this equipment.

008_051514

014_051514

No user serviceable parts inside. Refer servicing to qualified service
personnel.

THE FOLLOWING SECTIONS OF THIS MANUAL ARE INTENDED ONLY
FOR QUALIFIED SERVICE PERSONNEL WHO ARE FAMILIAR WITH
ELECTRICAL EQUIPMENT. THESE ARE NOT INTENDED FOR THE
OPERATOR.

011_051514

027_010914

Page 13

gmpopcorn.com

Econo-Pop 14 Popper Export Model No. 2121NSX

ORDERING SPARE PARTS

1. Identify the needed part by checking it against the photos, illustrations, and/or

parts list.

2. Use only approved replacement parts when servicing this unit.

3. When ordering, please include part number, part name, and quantity needed.

4. Please include your model number, serial number, and date of manufacture (located

on the machine nameplate/data plate) with your order.

5. Address all parts orders to:

Parts Department
Gold Medal Products Co.
10700 Medallion Drive
Cincinnati, Ohio 45241-4807

Or, place orders by phone or online:

Phone: [phone]

[phone]

Fax: [phone]

[phone]
E-mail: [e-mail]
Web Page: gmpopcorn.com

Page 14

gmpopcorn.com

Econo-Pop 14 Popper Export Model No. 2121NSX

Replacing Broken Glass

Broken glass panels can be easily replaced. Gold Medal Products Co. does not ship glass. It can be
obtained from a local glass shop and always purchase tempered glass.

1. Remove all loose pieces of glass.

2. Remove all rigid glass channels from around the glass to be replaced. Set it aside as it

must be reused.

3. Carefully remove the rest of the broken glass.

4. Apply decals (if desired) to the new glass panel.

5. Slide rigid glass channels over the exposed sides and bottom of new glass panel.

6. Fasten new glass panel in machine with the existing glass strips. (On some units, the

front and side glass slide under top and is then lowered into the bottom channel.)

GLASS DIMENSIONS (W x H x D)

Front Glass: 24 3/16” X 24” X 1/8” (1 Piece)

Side Glass: 16 3/4” X 24 3/16” X 1/8” (2 Pieces)

Page 15

gmpopcorn.com

21

Co

mplete Agitator Assembly

(Includes Lids)

Complete Kettle Assembly

See Kettle

Complete Agitator

*See Parts

Econo-Pop 14 Popper Export Model No. 2121NSX

12/14 oz. Kettle Assy. (58220EX) – Agitator Assy.

.58220 Overall Image

1

2

3

Assembly
(Includes Lids)

4

13

12

5 6 7

11

10

8

14

9

Bottom Assy.

18

19, 20

22

15

16*

17

List note.

Page 16

gmpopcorn.com

58

220EX

1 1/4-20 X 1.25 THUMB SCREW

61068

2 8-32 X 1/2 PHILL

FLAT M/S ZINC

20066

3 SHELL & KETTLE BLOCK

61013

4 12/14 OZ LID&AGITATOR AS

SY

(Complete Assy.)

58219EX

5 CROSSBAR ASSEMBLY

61025

6 FORMED LID

47261

7 REAR KETTLE LID

47119

DUMP HANDLE ASSEMBLY (assembly includes

9 DUMP HANDLE KNOB

47110

10 DUMP HANDLE

47707

11 5/16-18 X 3/8 SQ HD SCREW (

Holds Key

) 47662

12 5/16-18 X 1/2 SQ HD SCREW

47725

13 WOODRUFF KEY #3 1/8X1/2

41730

14 AGITATOR B

EARIN

G HUB

43434

15 NEEDLE BEARING

47106

SPUR GEAR Kit

(Includes 2 gears with set screws.

17 10-32 X 3/16

SET SCREW

41742

18* AGITATOR SHAFT

61092

19 1/2ID X 7/8OD SET COLLAR

47326

20 SET SCREW 1/4

-

20 X 3/16

47751

21 AGITATOR WEIGHT

61093

22 STIR ROD

49011

Econo-Pop 14 Popper Export Model No. 2121NSX

12/14 oz. Kettle Assy. (58220EX) – Agitator Assy. – Parts List

Item

8

Handle, Knob, 2 SQ HD Screws, and Key)

16

Always replace Agitator Spur Gear and Kettle
Drive Motor Gear as a set.)

Part Description

Part Number

47102

47059K

Page 17

gmpopcorn.com

58220EX

12/14 OZ. KETTLE BOTTOM ASSEMBLY

2 KETTLE SHELL

61017

3 KETTLE LEAD ASSY

61030

4 KETTLE GASKET

61012

5 12/14 KETTLE WITH HEATER

58011EX

6 12/14OZ SHUNT BAR

77879

7 8-32 TOP LOCK NUT (always replace

if removed)

67943

482°F

THERMOSTAT (includes two 6

-

32 screws)

Lock Nut View

Top Lock Nut

- Fastens

As of

February

1, 201

6, the

EXPORT

Kettle

Export L6

-15R

Export L6

-

15P

Econo-Pop 14 Popper Export Model No. 2121NSX

12/14 oz. Kettle Assembly (58220EX) – Kettle Bottom View

1

Kettle Bottom Assembly

2

3

Lead-in Assembly Plug is 230V (NEMA L-6).
When replacing the lead-in assembly, ensure
the kettle receptacle will match the new
configuration (see image below).

Kettle Recpt.

(P/N 49330EX)

Kettle Plug

Configuration

8

6

5

4

Element View

7

each thermostat and
ground. Install Lock Nut
with triangle in UP
position (as shown).

ONE TIME USE ONLY,
REPLACE NUT if
removed.

Thermostat

Welded Stud

Item

1

(includes parts listed below)

8

(two thermostats required)

Part Description

Page 18

Part Number

58221EX

76708

gmpopcorn.com

2121NS

X

1 RED POWDER COAT DOME

16123

GLASS CHAN 23 13/16

(side channel used on

GLASS CHAN 16 11/16

(top and bottom channel

GLASS CHAN 24 (top and bottom channel for

5 GLIDE

47328

6 BLACK CRUTCH TIP

49123

For Glass Panels,

Econo-Pop 14 Popper Export Model No. 2121NSX

Cabinet Exterior – Front View

1

3, 4

2

see Replacing
Glass section.

5

6

Item

2

front glass and side glass)

3

for side glass)

4

front glass)

Part Description

Part No.

47695

47693

47696

Page 19

gmpopcorn.com

2121NS

X

1 MAGNETIC CATCH

47561

2 MAGNETIC CATCH MOUNT BRACKET

47559

3* COMPLETE HARDWARE KIT FOR LH DOOR

47054

4* COMPLETE HARDWARE KIT FOR RH DOOR

47055

8-32 X 3/8 SLT HWH M/S

(Frame hinge screws

6 PLEXIGLASS DOOR

77058

7 DROP PANEL ASSEMBLY

47006

8 OLD MAID PAN

47003

9 #SR-6W-1 STRAIN RELIEF

82220

10**

EXPORT POWER SUPPLY CORD

42369

* Complete Left and Right Hand Door

individual

component breakdown.

3* 4*

1

8

**

CAUTION: If supply cord is damaged, it must be replaced by

Econo-Pop 14 Popper Export Model No. 2121NSX

Cabinet Exterior – Rear View

Hardware Kits - See next page for

2

5

6

10**

9

7

Gold Medal Products Co., its service agent, or similarly
qualified persons in order to avoid a hazard.

Item

5

not included with Door Hardware Kit)

Part Description

Page 20

Part No.

42044

gmpopcorn.com

47054

47055

1 DOOR KNOB

41013

41013

2 8-32 X ½ SCREWS PH PAN W/SEMS

47124

47124

3 ACORN NUT #8

-32

47702

47702

4 TEE BOLT

75267

75267

5 MALE HINGE SHORT LEFT

41349

6 FEMALE HINGE LONG LEFT

41352

7 FEMALE HINGE LONG RIGHT

41351

8 MALE

HINGE SHORT RIGHT

41350

7

5

Complete Left Hand Door

Complete Right Hand Door

Econo-Pop 14 Popper Export Model No. 2121NSX

Door Hardware Kits – Individual Component Breakdown

1

2

6

Hardware Kit (P/N 47054)

(contains all parts shown above)

3

4

2

3

8

Hardware Kit (P/N 47055)

(contains all parts shown above)

Item

Part Description

Part Number

Page 21

gmpopcorn.com

2121NS

X

1 3 HOLE ROCKER SWITCH

17473

2 SWITCHES LABEL

48508

3 SWITCH, LIGHTED ROCKER GR

42798

4 HALOGEN FLOOD

(Max. 75 Watt)

41979

EX

5 REAR HANGER ARM ASSEMBLY

47263

6 FRONT HANGER ARM

47262

7 10-32 X 3/16 SET SCREW

41742

SPUR GEAR KIT (Includes 2 gears with set

9 GEAR BLOCK ASSEMBLY

67194

KETTLE LEAD

-

IN RECEPTICLE

(referenc

e Kettle

*See Parts List note.

Econo-Pop 14 Popper Export Model No. 2121NSX

Cabinet Interior – Hanger Assembly/Controls View

2 3

1

10

4

5

6

9

8*

7

Item

8

screws. Always replace Agitator Spur Gear and
Kettle Drive Motor Gear as a set.)

Part Description

Part No.

47059K

10

Bottom Assy. for kettle plug configuration note)

Page 22

49330EX

gmpopcorn.com

2121NS

X

BOTTOM CORN PAN ASSEMBLY

220V

2 HEAT ELEMENT 230V,75W

44075

3 COVER CORN PAN CONDUIT

47653

4 SR 15

-

1 STRAIN RELIEF

61099

5 MALE CORDSET

61020

6 FEMALE CORDSET

61021

7 SR 6P3

-

4 STRAIN RELIEF

76026

8 CORNER COVER

77591

9 OLD MAID PAN

47003

Econo-Pop 14 Popper Export Model No. 2121NSX

Cabinet Interior – Heated Corn Deck

3

1

2

4

5

6

7

8

9

Item

1

(Complete assembly includes element)

Part Description

Part No.

77076EX

Page 23

gmpopcorn.com

2121NS

X

1 LIGHT CONICAL

SHORT

49584

2 LAMP HOLDER

47047

3 KETTLE DRIVE MOTOR

230 VOLT

47067

KETTLE LEAD

-

IN RECEPTICLE (reference Kettle

5 .625” SNAP BUSHING

47282

6 8 TERMINIAL TERMINAL BLOCK

47208

5

See

Controls View

General image shown for parts reference only.

Model 2121NS image

Econo-Pop 14 Popper Export Model No. 2121NSX

Dome Interior – Electrical Breakdown

1

2

6

3

4

Item

Part Description

Part No.

4

Bottom Assy. for kettle plug configuration note)

Page 24

49330EX

gmpopcorn.com

2121NSX

1 WARNING, MAX LAMP 75W

41452

2 UNIVERSAL POPPER DECAL

41019

3 MAIN GROUND LABEL

42375

4 WARNING, SURFACE CONTACT

87087

5 CONDUIT WARNING LABEL

82840

6 WARNING LABEL CORD

68720

Unit

Labels

Kettle Lead

-

In Label

Power Cord Label

s

Econo-Pop 14 Popper Export Model No. 2121NSX

Safety Labels

1

2

5

6

3

4

Item

Part Description

Page 25

Part Number

gmpopcorn.com

2121NS

X

1 STAMPED ALUMINUM SCOOP

2071

2 MEASURE 14.7 CC

47679

3 MEASURE ½ CUP

47149

4 14 OZ. VOLUME CORN MEASURE

47399

Econo-Pop 14 Popper Export Model No. 2121NSX

Accessories

1

Item

2

Part Description

3

4

Part No.

Page 26

gmpopcorn.com

Econo-Pop 14 Popper Export Model No. 2121NSX

Wiring Diagram

Model No. 2121NSX

Page 27

gmpopcorn.com

10700 Medallion Drive, Cincinnati, Ohio 45241

-

4807 USA

Econo-Pop 14 Popper Export Model No. 2121NSX

WARRANTY

Gold Medal Products Co. warrants to the original purchaser each item of its manufacture to
be free of defects in workmanship and material under normal use and service. Gold Medal
Products Co.’s obligation under this warranty is limited solely to repairing or replacing parts,
f.o.b. Cincinnati, Ohio, which in its judgment are defective in workmanship or material and
which are returned, freight prepaid, to its Cincinnati, Ohio factory or other designated point.
Except for “Perishable Parts” on specific machines, the above warranty applies for a period
of two (2) years from the date of original sale to the original purchaser of equipment when
recommended operating instructions and maintenance procedures have been followed. These
are packed with the machine. Parts warranty is two (2) years, labor is six (6) months.

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR
IMPLIED, AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR PART,
INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY. THERE ARE
NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE
HEREOF. In no event shall Gold Medal Products Co. be liable for special, incidental or
consequential damages. No claim under this warranty will be honored if the equipment covered
has been misused, neglected, damaged in transit, or has been tampered with or changed in any
way. No claim under this warranty shall be honored in the event that components in the unit at
the time of the claim were not supplied or approved by Gold Medal Products Co. This warranty
is effective only when electrical items have been properly attached to city utility lines only at
proper voltages. This warranty is not transferable without the written consent of Gold Medal
Products Co.

The term “Original Purchaser” as used in this warranty shall be deemed to mean that person,
firm, association, or corporation who was billed by the GOLD MEDAL PRODUCTS CO.,
or their authorized distributor for the equipment.

THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL
PURCHASER FIRST CALLS GOLD MEDAL PRODUCTS CO. AT 1-800-543-0862 TO
DISCUSS WITH OUR SERVICE REPRESENTATIVE THE EQUIPMENT PROBLEM,
AND, IF NECESSARY, FOR INSTRUCTIONS CONCERNING THE REPAIR OR
REPLACEMENT OF PARTS.

NOTE: This equipment is manufactured and sold for commercial use only.

Phone: [phone] Fax: [phone]
[phone] [phone]

© 2016 – The text, descriptions, graphics, layout, and other material in this publication are the exclusive property of
Gold Medal Products Co. and shall not be used, copied, reproduced, or published in any fashion, including website
display, without its express written consent.

gmpopcorn.com

Page 28

gmpopcorn.com