Gold Medal Citation 2001ST, Citation 2001 User Manual

Citation

16 oz. Popper

Model 2001

Model 2001ST

Instruction Manual

Model No. 2001, 2001ST

10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA

Part No. 67861

DANGER

WARNING

Citation 16 oz. Popper Model No. 2001, 2001ST

SAFETY PRECAUTIONS

Machine must be properly grounded to prevent electrical shock to personnel. Failure to do so could result in serious injury, or death. DO NOT immerse any part of this equipment in water. DO NOT use excessive water when cleaning. Keep cord and plug off the ground and away from moisture. Always unplug the equipment before cleaning or servicing. Make sure all machine switches are in the OFF position before plugging the equipment into the receptacle.

Improper installation, adjustment, alteration, service, or maintenance can cause property damage, injury, or death. Any alterations to this equipment will void the warranty and may cause a dangerous condition. This appliance is not intended to be operated by means of an external timer or separate remote-control system. NEVER make alterations to this equipment. Read the Installation, Operating, and Maintenance Instructions thoroughly before installing, servicing, or operating this equipment.

008_051514

014_020416

To avoid burns, DO NOT touch the kettle or any heated surface. DO NOT place or leave objects in contact with heated surfaces.

013_092414

ALWAYS wear safety glasses when servicing this equipment.

010_010914

No user serviceable parts inside. Refer servicing to qualified service personnel.

011_051514

Read and understand operator’s manual and all other safety instructions before using this equipment. To order copies of the operator’s manual go to gmpopcorn.com or write to Gold Medal Products Co., 10700 Medallion Drive, Cincinnati, OH 45241 USA 1-(800)-543-0862

022_060215

Page 2

gmpopcorn.com

WARNING

Citation 16 oz. Popper Model No. 2001, 2001ST

SAFETY PRECAUTIONS (continued)

DO NOT allow direct contact of this equipment by the public when used in food service locations. Only personnel trained and experienced in the equipment operation may operate this equipment. Carefully read all instructions before operation.

This machine is NOT to be operated by minors.

Note: Improvements are always being made to Gold Medal’s equipment. This

information may not be the latest available for your purposes. It is critical that you call Gold Medal’s Technical Service Department at 1-800-543-0862 for any questions about your machine operations, replacement parts, or any service questions. (Gold Medal Products Co. does not assume any liability for injury due to careless handling and/or reckless operation of this equipment.)

012_010914

007_010914

Page 3

gmpopcorn.com

Measure 22 cc

16 oz. Corn Measure

6 oz Measure

Bulb for Cabinet

Aluminum

Citation 16 oz. Popper Model No. 2001, 2001ST

INSTALLATION INSTRUCTIONS

Inspection of Shipment

After unpacking, check thoroughly for any damage which may have occurred in transit. Claims should be filed immediately with the transportation company. The warranty does not cover damage that occurs in transit, or damage caused by abuse, or consequential damage due to the operation of this machine, since it is beyond our control (reference warranty in back of manual).

Manual

Read and understand the operator’s manual and all other safety instructions before using this equipment. To order copies of the operator’s manual go to gmpopcorn.com or write to Gold Medal Products Co., 10700 Medallion Drive, Cincinnati, OH 45241 USA 1-(800)-543-0862.

Model Description

2001: 16 oz. Citation Popper with a white molded, LED lighted dome. Unit has a forced air

popcorn crisping system.

2001ST: 16 oz. Citation Popper with a stainless steel, LED lighted dome. Unit has a forced

air popcorn crisping system.

Items Included with this Unit

Scoop

Interior

Page 4

gmpopcorn.com

Citation 16 oz. Popper Model No. 2001, 2001ST

Setup

This unit has been tested at the factory.

1. Remove all packaging and tape prior to operation.

2. Place the unit on a sturdy, level base.

3. The Popper blower vents out the top of unit, allow adequate clearance for airflow.

4. The door knobs are shipped facing the inside of the machine. Re-adjust knobs to face

the outside of the machine.

5. Carefully install the light bulb (do not over-tighten) into the lamp holder located in the

cabinet interior. Ensure the unit is OFF and unplugged before installing or changing the bulb (reference the Electrical Requirements section).

6. Make sure kettle lead-in cord is securely plugged into unit, and twisted to lock into the

kettle receptacle.

7. After setup, the unit should be cleaned prior to use (see Care and Cleaning section of

this manual).

Page 5

gmpopcorn.com

DANGER

CAUTION

Citation 16 oz. Popper Model No. 2001, 2001ST

Electrical Requirements

The following power supply must be provided:

2001, 2001ST: 120 V~, 1920 W, 60 Hz

Machine must be properly grounded to prevent electrical shock to personnel. Failure to do so could result in serious injury, or death. DO NOT immerse any part of this equipment in water. DO NOT use excessive water when cleaning. Keep cord and plug off the ground and away from moisture. Always unplug the equipment before cleaning or servicing. Make sure all machine switches are in the OFF position before plugging the equipment into the receptacle.

A certified electrician must furnish sufficient power for proper machine operation and install any supplied receptacle. We recommend this equipment be on a dedicated and protected circuit. Failure to wire properly will void the warranty and may result in damage to the machine. It is Gold Medal Products Co.’s recommendation that this machine be plugged directly into a wall outlet. The use of extension cords is not recommended due to safety concerns, and may cause sacrificed and/or reduced performance. Make sure cord is located to prevent a trip hazard or unit upset.

008_051514

Before You Plug In Machine

1. Make sure all machine switches are OFF before plugging equipment into receptacle.

2. Make sure wall outlet can accept the grounded plugs (where applicable) on the power

supply cord.

3. The wall outlet must have the proper polarity. If in doubt, have a competent

electrician inspect the outlet and correct if necessary.

4. DO NOT use a grounded to un-grounded receptacle adapter (where applicable).

5. Install unit in a level position.

If the supply cord is damaged, it must be replaced by Gold Medal Products Co., its service agent or similarly qualified persons in order to avoid a hazard.

039_080614

Page 6

gmpopcorn.com

Warmer Switch

Kettle Motor Switch

Citation 16 oz. Popper Model No. 2001, 2001ST

OPERATING INSTRUCTIONS

Controls and Their Functions

LIGHTS SWITCH

Two position, ON/OFF lighted rocker switch - supplies power to the popcorn sign and interior cabinet light. The green switch light ON indicates there is power to the lights.

KETTLE HEAT SWITCH

Two position, ON/OFF lighted rocker switch - supplies power to the heating elements in the popping kettle. The green switch light ON indicates there is power to the kettle heating element.

KETTLE MOTOR SWITCH

Two position, ON/OFF lighted rocker switch - supplies power to the kettle agitator motor and exhaust blower. The Kettle Motor Switch MUST be ON at all times when there is popcorn (popped or un-popped) in the kettle. The green switch light ON indicates there is power to the agitator motor and exhaust blower.

WARMER SWITCH

Two position, ON/OFF lighted rocker switch - supplies power to the heat element for the corn deck freshener. The green switch light ON indicates there is power to the corn pan heat element.

Kettle Heat Switch

Lights Switch

Page 7

gmpopcorn.com

Kettle Size

Popcorn Charge

Oil Charge

Flavacol (Salt)

16 oz.

16 oz. (473 ml)

5 oz.

(148 ml)

1.5 Tblsp. (20cc)

Citation 16 oz. Popper Model No. 2001, 2001ST

Popping Corn

This section describes instructions for popping Standard (salted popcorn)

Amount of Popcorn and Oil

The popper is equipped with a corn, salt, and oil measure. We recommend flavored and colored coconut oil. Popcorn popped in coconut oil stays fresh longer and does not leave black deposits in the kettle like other oils. Use only top quality, fresh popcorn from reputable suppliers.

Ingredient amounts for popping Standard Popcorn:

For best results use Mega-Pop® 16 oz. premeasured pouches (Item# 2846).

Popping Standard (Salted) Popcorn

1. Turn all switches ON.

2. To determine when kettle is ready to pop corn (about 4 minutes), test pop three

kernels of corn in one ounce (30 ml) of popping oil. When kernels pop, kettle is ready.

3. Lift kettle lid and load Mega-Pop® premeasured popcorn and oil pouch, or pour in

popcorn and Flavacol, then add oil in premeasured amount. Close lid.

4. When corn has finished popping, gently dump the popcorn.

5. On final kettle of corn, turn Kettle Heat Switch OFF just as lids are forced open by the

popping corn. This procedure saves electricity, since kettle has plenty of heat, and helps eliminate smoke/odor from any oil residue that remains after popping has stopped.

6. When finished popping, turn KETTLE HEAT and KETTLE MOTOR switches OFF.

NEVER LEAVE THE HEAT ON WHEN YOU ARE NOT POPPING CORN!

Page 8

gmpopcorn.com

DANGER

WARNING

Citation 16 oz. Popper Model No. 2001, 2001ST

Care and Cleaning

Machine must be properly grounded to prevent electrical shock to personnel.

DO NOT immerse in water.

Always unplug the equipment before cleaning or servicing.

To avoid serious burns, DO NOT touch the kettle while it is hot!

Good sanitation practice demands that all food preparation equipment be cleaned regularly (only use non-toxic, food grade cleaners). A clean looking, well-kept machine is one of the best ways of advertising your product.

025_020314

028_082715

Note: It is extremely important to follow all cleaning procedures, otherwise parts

damage and equipment failure will result. The warranty does not cover parts that are damaged due to improper cleaning.

Daily Kettle Cleaning Instructions

CAUTION: A hot kettle will cause burns if you touch it with your hand. Allow kettle to cool

at least 1 hour before attempting to clean. DO NOT use ice or water to cool down a hot kettle! Severe kettle damage will result!

1. When cool, wipe outside of kettle with a clean, soft cloth. DO NOT use oven cleaners or

abrasive materials as they will damage the kettle.

2. Every night, mix Gold Medal’s Heat’n Kleen solution (Item No. 2095), 2 tablespoons

per gallon of water. It is not necessary to use the entire gallon at once; only use enough to fill the kettle 1/2 inch deep.

3. Turn kettle heat ON. When water starts to boil, turn kettle heat OFF.

4. Allow to cool at least 1 hour, then dump solution into a bucket and wipe inside of

kettle with a clean cloth. Make sure all solution goes into the bucket; do not spill any in the interior of machine.

For an extra dirty kettle, the process may be repeated; or, after turning kettle heat OFF, allow solution to sit in kettle overnight. The next morning, dump solution into a bucket and wipe inside of kettle with a clean cloth.

5. With unit OFF and unplugged, wipe kettle lead cord with a clean SLIGHTLY damp cloth.

DO NOT get moisture into the kettle lead-in cord, severe damage will result.

Page 9

gmpopcorn.com

Filter

Step 2:

Remove filter by sliding it

Step 3:

Clean filter in warm soapy

Citation 16 oz. Popper Model No. 2001, 2001ST

Daily Unit Cleaning Instructions

1. Turn machine OFF, unplug unit and allow it to cool before attempting to clean.

2. Clean all pans/accessories in order to sanitize them before each use.

3. Take a clean, SLIGHTLY damp cloth and wipe excess grease from glass and cabinet.

4. Wipe stainless steel parts with a clean cloth and cleaner designed for stainless steel,

such as Gold Medal Watchdog Stainless Cleaner (Item No. 2088).

DO NOT use oven cleaners or abrasive materials as they will damage parts of machine.

5. Clean glass panels with glass cleaner. Gold Medal Watchdog Glass Cleaner (Item No.

2588) is recommended.

Ammonia cleaners will damage plastic doors/panels. Use only non-ammonia cleaners, such as Gold Medal Watchdog Glass Cleaner (Item No. 2588).

Weekly Filter Cleaning Instructions

The popcorn machine is equipped with an efficient and durable filtration system. The filter should be cleaned every week to maintain maximum efficiency.

Steps to Clean Filter

Step 1: Turn unit OFF and allow it

to cool before removing filter. is located inside the popcorn machine, above the popping kettle.

out of the filter retaining angles.

water, then rinse and allow to dry overnight. Reinstall filter to its original position (as shown above).

Filter

Page 10

gmpopcorn.com

Citation 16 oz. Popper Model No. 2001, 2001ST

Clean the Crisper/Blower Compartment

The blower compartment MUST be inspected/cleaned every 3-4 months by Qualified Service Personnel to maintain proper operation.

1. Turn machine OFF, unplug unit and allow it to cool before attempting to clean.

2. Lift off the corn pan to view the blower assembly.

3. Remove the blower cover and if required, carefully clean the blower compartment,

and underneath the element with a vacuum only (reference image shown).

4. After cleaning, reassemble blower cover and corn pan.

Page 11

gmpopcorn.com

Issue

Possible Cause

Solution

Power to the Unit

A. Power to

the

Unit A. Make sure the

unit’s power

cord is plugged in.

Kettle Does Not Heat

A. Power to the Kettle

A. Make sure kettle lead

-

in cord is plugged in and

B. Kettle Heat Switch

B. Have a qualified service person c

heck the

C. Heating Element

C. Heating element in the kettle may

be burned

Long Popping Cycles

A. Low Voltage

A. If the machine is operated on low voltage, this

B. Inadequate Supply Lines

B. Inadequately sized electrical supply lines

or

C. Inferior Corn

C. Inferior quality corn would result in longer

Kettle Agitator Shaft not

A. Kettle Motor Switch

A. If the kettle agitator shaft is not rotating,

B. Kettle Agitator

S

haft

/Stir

B. If the kettle agitator shaft is not rotating,

Citation 16 oz. Popper Model No. 2001, 2001ST

Troubleshooting

twisted to lock into the kettle receptacle.

voltage to and from the Kettle Heat Switch; if switch is defective, replace it.

out. Check with a qualified service person for inspection/repair.

(Longer than 4 minutes for Salt Popcorn)

Rotating

Blade not rotating. (Unit must be OFF, unplugged and cool prior to checking or adjusting the agitator assembly.)

could cause the kettle not to reach the proper operating temperature. Check with a qualified electrician.

use of extension cord, in addition to being a fire hazard, would also prevent the kettle from reaching the proper operating temperature. Check with a qualified electrician.

popping cycles. Use only top quality hybrid popcorn from reputable suppliers. Even then, if you let your corn pick up moisture or dry out, your popping cycles will be slow.

DO NOT pop corn. Make sure the Kettle Motor Switch is ON. If the switch is ON, and the shaft is not rotating, the switch or motor may be faulty, contact qualified service personnel for inspection/repair.

DO NOT pop corn. Check the clearance between the kettle bottom and the stir blade; it should be 1/32” (use a dime). To adjust, reference the Agitator Set Collar Adjustment section.

Page 12

gmpopcorn.com

Step 1:

Make sure machine is OFF and

Drive Motor

Agitator’s Spur Gear

Set Collar

Agitator shown for general image

Set Collar above

Lower Set Collar

Adjust clearance to

Agitator Weight

3/16” to 1/4” max.

Stir Rod

Spur Gear Placement

Crossbar

Citation 16 oz. Popper Model No. 2001, 2001ST

Agitator Set Collar Adjustment

The following instructions describe how to properly adjust set collars on an agitator assembly with a floating stir rod.

Steps to Adjust Set Collars

unplugged, then allow unit to cool completely before attempting to adjust the agitator height.

Step 2: Loosen the set screw in each set collar to be adjusted.

Step 3: With the kettle mounted in the popper, adjust the shaft so the Agitator’s Spur Gear contacts half of the Drive Motor Spur Gear (reference Spur Gear Placement image at right). DO NOT set spur gears at full gear contact; it can cause binding as the kettle is dumped.

Step 4: Once shaft is positioned correctly, re-tighten the set screw in the set collar above the crossbar to secure in place.

Step 5: Adjust clearance between the bottom of the crossbar and the lower set collar to 1/32” (thickness of a dime); then re-tighten set screw to secure in place (see image below).

Step 6: Adjust set collar for agitator weight to be between 3/16” to 1/4” above the agitator weight. Once adjusted, re-tighten set screw to secure in place.

should set halfway up on Drive Motor Spur Gear.

Crossbar

Spur Gear

w/Set screw

reference only (lids not shown for clarity).

thickness of a dime.

Page 13

(below Crossbar)

Set Collar (for Agitator Weight)

gmpopcorn.com

DANGER

WARNING

CAUTION

Citation 16 oz. Popper Model No. 2001, 2001ST

MAINTENANCE INSTRUCTIONS

Machine must be properly grounded to prevent electrical shock to personnel. Failure to do so could result in serious injury, or death. DO NOT immerse any part of this equipment in water. DO NOT use excessive water when cleaning. Keep cord and plug off the ground and away from moisture. Always unplug the equipment before cleaning or servicing. Make sure all machine switches are in the OFF position before plugging the equipment into the receptacle.

Improper installation, adjustment, alteration, service, or maintenance can cause property damage, injury, or death. Any alterations to this equipment will void the warranty and may cause a dangerous condition. This appliance is not intended to be operated by means of an external timer or separate remote-control system. NEVER make alterations to this equipment. Read the Installation, Operating, and Maintenance Instructions thoroughly before installing, servicing, or operating this equipment.

008_051514

014_020416

No user serviceable parts inside. Refer servicing to qualified service personnel.

THE FOLLOWING SECTIONS OF THIS MANUAL ARE INTENDED ONLY FOR QUALIFIED SERVICE PERSONNEL WHO ARE FAMILIAR WITH ELECTRICAL EQUIPMENT. THESE ARE NOT INTENDED FOR THE OPERATOR.

011_051514

027_010914

Page 14

gmpopcorn.com

Citation 16 oz. Popper Model No. 2001, 2001ST

ORDERING SPARE PARTS

1. Identify the needed part by checking it against the photos, illustrations, and/or

parts list.

2. Use only approved replacement parts when servicing this unit.

3. When ordering, please include part number, part name, and quantity needed.

4. Please include your model number, serial number, and date of manufacture (located

on the machine nameplate/data plate) with your order.

5. Address all parts orders to:

Parts Department Gold Medal Products Co. 10700 Medallion Drive Cincinnati, Ohio 45241-4807

Or, place orders by phone or online:

Phone: (800) 543-0862

(513) 769-7676

Fax: (800) 542-1496

(513) 769-8500 E-mail: info@gmpopcorn.com Web Page: gmpopcorn.com

Page 15

gmpopcorn.com

Citation 16 oz. Popper Model No. 2001, 2001ST

Replacing Broken Glass

Broken glass panels can be easily replaced. Gold Medal Products Co. does not ship glass. It can be obtained from a local glass shop, always purchase tempered glass.

GLASS DIMENSIONS (Height x Width x Thickness)

Front Glass: 28 3/16” x 22 15/16” x 1/8” (1 Piece) Side Glass: 28 3/16” x 15 1/2” x 1/8” (2 Pieces)

1. Turn machine OFF, unplug unit and allow it to cool before attempting to replace glass.

2. Carefully remove all loose pieces of broken glass.

3. Lift out the corn pan (bottom pan).

4. Locate the Glass Retainer Strips on each corner post holding in the glass panel, and

remove the screws to unfasten the retainers.

5. Carefully remove the rest of the broken glass.

6. Remove all rigid glass channels from around the glass to be replaced, set channels

aside for reuse.

7. Apply decals (if desired) to new glass panel.

8. Slide rigid glass channels over the exposed sides and bottom of new glass panel.

9. Fasten new glass panel in machine with existing glass strips and screws.

10. Reinstall corn pan (bottom pan).

Page 16

gmpopcorn.com

55199

1 1/4-20 X 1 THUMB SCREW

47691

2 8-32 X 1/2 PHILL FLAT M/S ZINC

20066

3 THREADED BLOCK

61167

4 LID & AGITATOR ASSEMBLY (Complete Assy.)

41181

5 CROSSBAR ASSEMBLY

41180

6 FRONT LID

41123

7 REAR LID

41120

8 AGITATOR

BEARING HUB

43434

9 NEEDLE BEARING

47106

SPUR GEAR KIT (Includes 2 gears with set

11 10-32 X 3/16 SET SCREW

41742

12 AGITATOR SHAFT ASSEMBLY

41093

13 ½ ID X

7/8 OD SET COLLAR

47326

14 ¼-20 X 3/16 SET SCREW

47751

55199 Overall Kettle

Complete Agitator Assembly

Co

mplete Agitator Assy.

*See Parts

Complete Kettle Assembly

See Kettle Bottom

Citation 16 oz. Popper Model No. 2001, 2001ST

16 oz. Kettle Assembly (55199) – Agitator Assembly View

55199E Exp. Views

55199E Ag. Assy.

1

2

3

Assy. section for parts breakdown (includes Handle Assembly and Kettle Lead).

4

(Includes Lids)

5 6 7

8

9

10*

11

12

List note.

13, 14

Item

10*

screws. Always replace Agitator Spur Gear and Kettle Drive Motor Gear as a set.)

(Includes Lids)

Part Description

Part Number

47059K

Page 17

gmpopcorn.com

Element View

Use high temp

the three flange

11 10

Top Lock Nut

- Fastens each

with triangle

55199 Kettle Element

15

Kettle Bottom Assembly View

23 21 20

*

Dump Handle

Kettle

Conduit

Label

(not shown)

Citation 16 oz. Popper Model No. 2001, 2001ST

16 oz. Kettle Assembly (55199) – Kettle Bottom Assembly

thermostat and ground. Install Lock Nut in UP position (as shown).

ONE TIME USE ONLY,

1

12

2

3

4

REPLACE NUT if removed.

9

55199EX Kettle Bottom Assy.

55199E exp. views

red Loctite on

nuts.

18*

Assembly (includes Knob)

22

13 14

16 17

8

7

6

5

24

25, 26

19

Page 18

gmpopcorn.com

55199

16OZ KETTLE BOTTOM ASSY (Complete Assy.)

55200

1 TRANSFER PLATE ASSY (beneath heat element)

67944

2 KETTLE GASKET

41598

3 KETTLE WELDMENT

67892

4 8-32 SERRATED FLANGE NUT

5 ¼ -

20 SERRATED LOCK NUT

46311

6 ELEMENT CLAMP (6 required)

67894

7 1550

TUBULAR HEAT ELEMENT

67014

8 LIMIT THERMOSTAT SHIELD

67959

9 8-32 TOP LOCK NUT (always replace if removed)

67943

10 482 F THERMOSTAT (includes two 6

-

32 screws)

76708

10 420 F THERMOSTAT (includes two 6

-

32 screws)

11 THERMOSTAT SHUNT BAR

47193

12 550 F THERMOSTAT (includes two 6

-

32 screws)

77108

KETTLE SHELL ASSEMBLY (has Pivot Pins

14 KETTLE LEAD ASSEMBLY

47361

8-32 x 3/8 SLT HWHW M/S (fastens Nameplate

16 JUNCTION BOX

47393

17 KETTLE CONDUIT LABEL

82840

DUMP HANDLE ASSEMBLY (assembly includes

19 DUMP HANDLE KNOB

47110

20 DUMP HANDLE

47707

21 3 1/8 X ½ WOODRUFF KEY

41730

22 5/16

– 18 X ½ SQ HD SCREW

47725

23 5/16

– 18 X 3/8 SQ HD SCREW (holds key)

47662

24 PIVOT PIN

41426

25 1/4-20 ACORN NUT

42229

26 1/4-20 X 3/8 BUTTON HEAD

12492

Citation 16 oz. Popper Model No. 2001, 2001ST

16 oz. Kettle Assembly (55199) – Kettle Bottom Assy. – Parts List

Item

13

attached)

15

to Jct. Box, and fastens Jct. Box to Kettle)

18

Handle, Knob, 2 SQ HD Screws, and Key)

Part Description

Part Number

41081

42044

47102

Page 19

gmpopcorn.com

2001,

2001ST

27 13/16” GLASS CHANNEL

(used on side edges

22 7/8” GLASS CHANNEL (used on bottom edge

15 3/8” GLASS CHANNEL (used on bottom edge

4 RUBBER FEET

(4 required)

41282

5 10-24 x 1 1/8 PAN HEAD (fastens rubber feet)

47128

6 10-24 LOCK NUT

(fastens rubber feet)

49363

See Kettle

See Dome

and

For Glass Panels,

2005ST

Citation 16 oz. Popper Model No. 2001, 2001ST

Cabinet Exterior – Front View

Assembly section.

Lighted Sign Assembly section.

see Replacing Glass section.

1

4, 5, 6

General image shown for parts reference only.

2, 3

Item

1

of front and side glass panels)

2

of front glass panels)

3

of side glass panels)

Part Description

Part Number

47697

47694

47692

Page 20

gmpopcorn.com

2001,

2001ST

1 MAGNETIC CATCH

47561

2 MAGNETIC CATCH BRACKET

47559

3** COMPLETE HARDWARE KIT FOR RH DOOR

47055

4** COMPLETE HARDWARE KIT FOR LH DOOR

47054

8-32 X 3/8 SLT. HWH M/S (Frame Hinge Screws

6 DOOR

47600

7 DROP PANEL ASSEMBLY

41017

8 OLD MAID PAN

61181

9 SR-6P-4

STRAIN RELIEF

44073

10* LEAD

-

IN CORD 20 AMP PLUG

47580

**

Complete

Door

Hardware Kit

For Labels, see

*

CAUTION: If supply cord is damaged, it must

2003

5

Data Plate

General image shown for parts reference only

Citation 16 oz. Popper Model No. 2001, 2001ST

Cabinet Exterior – Rear View

(See next page for individual component breakdown).

4**

6

Safety Label

7

Section.

1, 2

3**

9

8

10*

be replaced by Gold Medal Products Co., its service agent, or similarly qualified persons in order to avoid a hazard.

Item

5

not included in Door Hardware Kit)

Part Description

Part Number

42044

Page 21

gmpopcorn.com

47054

47055

1 DOOR KNOB

41013

2 8-32 X 1/2

SCREWS PH PAN W/SEMS

47124

3 ACORN NUT #8

-32

47702

4 TEE BOLT

75267

5 MALE HINGE SHORT LEFT

41349

6 FEMALE HINGE LONG LEFT

41352

7 FEMALE HINGE LONG RIGHT

41351

8 MALE HINGE SHORT RIGHT

41350

7 6 5

Complete Left Hand Door

Complete Right Hand Door

Citation 16 oz. Popper Model No. 2001, 2001ST

Door Hardware Kits – Individual Component Breakdown

1

2

Hardware Kit (P/N 47054)

(contains all parts shown above)

3

4

2

3

8

Hardware Kit (P/N 47055)

(contains all parts shown above)

Item

Part Description

Part Number

Page 22

gmpopcorn.com

2001,

2001ST

1 5 HOLE SWITCH BOX

17450

2 HOLE PLUG

45395

3 ROCKER SWITCH LABEL

48542

4 LIGHTED ROCKER SWITCH

42798

5 COVER PLATE FOR NO OIL

77478

6 FILTER RETAIN ANGLE

41644

7 FILTER

47043

8 65WATT COATED REFLECTOR

47176

9 FRONT

HANGER ARM ASSEMBLY

47262

10 REAR

HANGER ARM

ASSEMBLY

47

228

SPUR GEAR KIT (Includes 2 gears with set

12 10-32”

X 3/16

”

SET SCREW

41742

13 GEAR BLOCK ASSEMBLY

67194

10-24 X 1 HEX MACH SCREW (fastens gear block

15 CIRCUIT BREAKER 15 AMP

47364

16 20

A TWIST

MOUNTING PLATE

7747

6

17 KETTLE LEAD IN RECPT

47327

3 2

For Labels, s

ee

General image shown for parts reference only.

*See Parts

Citation 16 oz. Popper Model No. 2001, 2001ST

Cabinet Interior – Hanger Assembly/Controls View

1

Safety Label Section.

5

6

2005ST

4

7

8

13, 14

15

17

16

11*, 12

10

List note.

9

Item

Part Description

Part Number

11*

screws. Always replace Agitator Spur Gear and Kettle Drive Motor Gear as a set.)

14

assembly to kettle drive motor)

Page 23

47059K

49322

gmpopcorn.com

2001,

2001ST

1 120

V 60CY EXHAUST BLOWER

47343

2 .500 IN SNAP BUSHING

47236

3 EXHAUST BLOWER PLUG & CORD

47199

4 10-24 X 5/8 PHIL PAN M/S

76000

5 FENDER WASHER

77882

6 #10-24 CAGE NUT

76081

7 FAN MOUNT BRACKET

61183

8 10-24 X 3/8 PAN HD PH

38111

9 190 WATT

HEAT ELEMENT

(2 required)

55437

10 U CLIP

55215

11 HEATER CLAMP

61133

12 HEATER MOUNT

61134

13 8-32 X 1/2 PH PAN W/SEMS

47124

14 8-32 HEX M/S NUT

74149

15 THERMOSTAT MOUNTING BRACKET

61186

16 6-32 X 3/8 PH PAN HD M/S

38087

17 #8 INTERNAL TOOTH WASHER

74150

18 6-32 ZINC PLATED HEX NUT

38005

19 190°F WARMER THERMOSTAT

47385

2 3

8

7

For Labels, s

ee

2001ST

Model

200

1

ST Shown

Citation 16 oz. Popper Model No. 2001, 2001ST

Cabinet Interior – Element View

9

1

19

16, 17, 18

15

4, 5, 6

13, 14 12 11

Item

6

10

Part Description

Safety Label section.

4, 5, 6

Part Number

Page 24

gmpopcorn.com

S

ee

Controls View

9

19 20 16

Control Box and Cover

models only

.

2001ST

Model 200

1

ST Shown

Citation 16 oz. Popper Model No. 2001, 2001ST

Dome Interior – Electrical Components

17

16

3, 4

1

2

5

6

3, 7

8

15

14

13

12

11

10, 7

9 18

Page 25

used on molded dome

7, 10

gmpopcorn.com

2001

2001ST

1 LIGHT SHIELD CONICAL

49480

2 LAMP HOLDER

47047

3 8-32 X 3/4 PHIL PAN

MS SS

39007

4 8-32 HEX NUT, ESLOK, S.S.

22070

5 120V/60CY EXHAUST BLOWER

47343

6 EXHAUST ELBOW

47506

47507

7 8-32 HEX M/S NUT

74149

8 8 POS TERMINAL BLOCK

47208

9 8-32X3/8 PAN HD PH SCREW

74141

10 8-32 X 1/2 PH

PAN W/SEMS

47124

11 KETTLE LEAD IN RECPT

47327

12 CIRCUIT BREAKER 15 AMP

47364

13 RELAY, 120VAC, DPDT

48645

14 120V KETTLE DRIVE MOTOR

47038

1/4-20 X 3/4 GRADE 5 BOLT

16 .625 IN SNAP

BUSHING

47282

17 MOLDED RECEPTACLE

47727

61006

18 CONTROL BOX COVER

79278

19 CONTROL BOX

79277

20 .500 IN BUSHING SNAP

47236

Citation 16 oz. Popper Model No. 2001, 2001ST

Dome Interior – Parts List

Item

15

(fastens hanger arm)

Part Description

Part Number

74520 74520

Page 26

gmpopcorn.com

2001ST

1 5/16-18 X 5/8 PH TR (fastens dome)

46638

2 5/16 FLAT WASHER

(fastens dome)

74134

3 DOME SPACER

54014

4 MAIN WRAPPER

41794

5 FRONT WRAPPER

41797

6 8-32 X 3/8 SLT. (fastens support angle)

42044

7 DOME SUPPORT ANGLE

41316

8 FRONT WRAPPER PLEX SIGN

41559

9 8-32 X 3/8 PH PAN

42227

10 8-32 HEX NUT

74149

11 LED STRIP COOL WHITE

55379

12 .500 IN SNAP BUSHING

47236

13 MOLDED PLUG

47726

14 24VDC 20W POWER SUPPLY

55394

15 6-32 X 3/8 PHIL PAN

39000

16 6-32 NUT

14221

Fastens Front

14

Citation 16 oz. Popper Model No. 2001, 2001ST

Lighted Sign Assembly – Stainless Steel Dome

2001ST

1

2

3

4

5

8

1

Front Wrapper - Front View

9, 10

13

6 7

11

15, 16

9

12

Front Wrapper - Rear View

Item

Part Description

10

Wrapper to Main Wrapper

Part Number

Page 27

gmpopcorn.com

2001

1 5/16-18 X 5/8 PH TR (fastens dome)

46638

2 5/16 FLAT

WASHER (fastens dome)

74134

3 DOME SPACER

54014

4 20” X 28” MOLDED DOME

77001

5 LED LIGHT ASSEMBLY

77040

6 LED MOUNTING

55475

7 8-32 X 3/8 PH PAN (fastens LED strip)

42227

8 8-32 HEX NUT (fastens LED Strip)

74149

9 LED STRIP COOL WHITE

55379

10 .500 IN SNAP BUSHING

47236

11 1/4-20 X 1/2 HEX HD (fastens LED mount.)

14821

12 FENDER WASHER (fastens LED mount.)

82101

13 1/4-20 SERRATED NUT (fastens LED mount.)

46311

14 MOLDED PLUG

47726

15 24VDC 20W POWER SUPPLY

55394

16 6-32 X 3/8

PHIL PAN (fastens power supply)

39000

17 6-

32 NUT (fastens power supply)

14221

15 14

Complete

LED

10

2003

Citation 16 oz. Popper Model No. 2001, 2001ST

Lighted Sign Assembly – Molded Dome

1

2

3

1

LED Light Assembly – Front View

11, 12

13

4

5

9

7, 8

6

Light Assembly

16, 17

LED Light Assembly – Rear View

Item

Part Description

Part Number

Page 28

gmpopcorn.com

All Models

1 UNIVERSAL POPPER DECAL

41019

2 WARNING, MAX LAMP 75W

41452

3 MAIN GROUND LABEL

42375

4 WARNING, SURFACE CONTACT

87087

5 CONDUIT WARNING LABEL

82840

6 WARNING LABEL CORD

68720

All Models

1 STAMPED ALUM SCOOP

2071

2 MEASURE 20

CC

47680

3 MEASURE 6 OZ

49049

4 16OZ CORN MEASURE W/HANDL

68050

3 1

Kettle Lead

-

In Label

Citation 16 oz. Popper Model No. 2001, 2001ST

Safety Labels

2

Unit Labels

1

3

5

4

6

Power Cord Label

Item

Part Description

Part Number

Accessories

Item

2

Part Description

Page 29

4

Part Number

gmpopcorn.com

Citation 16 oz. Popper Model No. 2001, 2001ST

Wiring Diagram

Model No. 2001 and 2001ST

Page 30

gmpopcorn.com

10700 Medallion Drive, Cincinnati, Ohio 45241

-

4807 USA

Citation 16 oz. Popper Model No. 2001, 2001ST

WARRANTY

Gold Medal Products Co. warrants to the original purchaser each item of its manufacture to be free of defects in workmanship and material under normal use and service. Gold Medal Products Co.’s obligation under this warranty is limited solely to repairing or replacing parts, f.o.b. Cincinnati, Ohio, which in its judgment are defective in workmanship or material and which are returned, freight prepaid, to its Cincinnati, Ohio factory or other designated point. Except for “Perishable Parts” on specific machines, the above warranty applies for a period of two (2) years from the date of original sale to the original purchaser of equipment when recommended operating instructions and maintenance procedures have been followed. These are packed with the machine. Parts warranty is two (2) years, labor is six (6) months.

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR PART, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. In no event shall Gold Medal Products Co. be liable for special, incidental or consequential damages. No claim under this warranty will be honored if the equipment covered has been misused, neglected, damaged in transit, or has been tampered with or changed in any way. No claim under this warranty shall be honored in the event that components in the unit at the time of the claim were not supplied or approved by Gold Medal Products Co. This warranty is effective only when electrical items have been properly attached to city utility lines only at proper voltages. This warranty is not transferable without the written consent of Gold Medal Products Co.

The term “Original Purchaser” as used in this warranty shall be deemed to mean that person, firm, association, or corporation who was billed by the GOLD MEDAL PRODUCTS CO., or their authorized distributor for the equipment.

THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL PURCHASER FIRST CALLS GOLD MEDAL PRODUCTS CO. AT 1-800-543-0862 TO DISCUSS WITH OUR SERVICE REPRESENTATIVE THE EQUIPMENT PROBLEM, AND, IF NECESSARY, FOR INSTRUCTIONS CONCERNING THE REPAIR OR REPLACEMENT OF PARTS.

NOTE: This equipment is manufactured and sold for commercial use only.

Phone: (800) 543-0862 Fax: (800) 542-1496 (513) 769-7676 (513) 769-8500

© 2016 – The text, descriptions, graphics, layout, and other material in this publication are the exclusive property of Gold Medal Products Co. and shall not be used, copied, reproduced, or published in any fashion, including website display, without its express written consent.

gmpopcorn.com

Page 31

gmpopcorn.com