Gold Medal Astro Pop 16oz Series, Astro Pop 16oz 2023XE, Astro Pop 16oz 2023XEN, Astro Pop 16oz 2023E Instruction Manual
Page 1
Astro Pop 16oz
Instruction Manual
Model No. 2023E, 2023XE, 2023XEN
Part No. 41474
10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA
Page 2
Astro Pop 16oz Model No. 2023E, 2023XE, 2023XEN
SAFETY PRECAUTIONS
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle.
DANGER
Improper installation, adjustment, alteration, service, or maintenance can
cause property damage, injury, or death. Any alterations to this equipment
will void the warranty and may cause a dangerous condition. This appliance
is not intended to be operated by means of an external timer or separate
remote-control system. NEVER make alterations to this equipment. Read the
Installation, Operating, and Maintenance Instructions thoroughly before
installing, servicing, or operating this equipment.
008_051514
014_020416
WARNING
To avoid burns, DO NOT touch the kettle or any heated surface.
DO NOT place or leave objects in contact with heated surfaces.
013_092414
WARNING
ALWAYS wear safety glasses when servicing this equipment.
010_010914
WARNING
No user serviceable parts inside. Refer servicing to qualified service
personnel.
011_051514
WARNING
Read and understand operator’s manual and all other safety instructions
before using this equipment. To order copies of the operator’s manual go to
gmpopcorn.com or write to Gold Medal Products Co., 10700 Medallion Drive,
Cincinnati, OH 45241 USA 1-(800)-543-0862
022_060215
Page 2
www.gmpopcorn.com
Page 3
Astro Pop 16oz Model No. 2023E, 2023XE, 2023XEN
SAFETY PRECAUTIONS (continued)
WARNING
DO NOT allow direct contact of this equipment by the public when used in
food service locations. Only personnel trained and experienced in the
equipment operation may operate this equipment.
Carefully read all instructions before operation.
WARNING
This machine is NOT to be operated by minors.
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety.
012_010914
007_010914
Note: Improvements are always being made to Gold Medal’s equipment. This
information may not be the latest available for your purposes. It is critical that
you call Gold Medal’s Technical Service Department at 1-800-543-0862 for any
questions about your machine operations, replacement parts, or any service
questions. (Gold Medal Products Co. does not assume any liability for injury due
to careless handling and/or reckless operation of this equipment.)
Page 3
www.gmpopcorn.com
Page 4
20cc Measure
6 oz. Measure
Light Bulb
16 oz. Corn Measure
Power Supply
Astro Pop 16oz Model No. 2023E, 2023XE, 2023XEN
INSTALLATION INSTRUCTIONS
Inspection of Shipment
After unpacking, check thoroughly for any damage which may have occurred in transit. Claims
should be filed immediately with the transportation company. The warranty does not cover
damage that occurs in transit, or damage caused by abuse, or consequential damage due to the
operation of this machine, since it is beyond our control (reference warranty in back of manual).
Manual
Read and understand the operator’s manual and all other safety instructions before using this
equipment. To order copies of the operator’s manual go to gmpopcorn.com or write to Gold
Medal Products Co., 10700 Medallion Drive, Cincinnati, OH 45241 USA 1-(800)-543-0862.
Items Included with this Unit
Aluminum Scoop
Setup
This unit has been tested at the factory.
1. Remove all packaging and tape prior to operation.
2. Place unit on a sturdy, level base for use.
3. Install the light bulb (do not over-tighten) into the lamp holder located inside the
cabinet on the ceiling of the popper. Always be sure the unit is OFF and unplugged
before installing or changing the bulb (reference the Electrical Requirements section).
with Handle
(bulb may vary by model)
Receptacle / Cover
(2023E Units Only)
4. Reference the instruction manual for the oil dispense unit for instructions on
connecting the unit to the popper.
5. After setup, the unit should be cleaned prior to use (see Care and Cleaning section of
this manual).
Page 4
www.gmpopcorn.com
Page 5
Astro Pop 16oz Model No. 2023E, 2023XE, 2023XEN
Electrical Requirements
The following power supply must be provided:
2023E: 120 V~, 2784 W, 60 Hz
2023XE, 2023XEN: 230 V~, 2784 W, 50 Hz
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle.
A certified electrician must furnish sufficient power for proper machine operation and install any
supplied receptacle. We recommend this equipment be on a dedicated and protected circuit.
Failure to wire properly will void the warranty and may result in damage to the machine. It is Gold
Medal Products Co.’s recommendation that this machine be plugged directly into a wall outlet. The
use of extension cords is not recommended due to safety concerns, and may cause sacrificed
and/or reduced performance. Make sure cord is located to prevent a trip hazard or unit upset.
008_051514
Before You Plug In Machine
1. Make sure all machine switches are in the OFF position before plugging the equipment
into the receptacle.
2. Make sure the wall outlet can accept the grounded plugs (where applicable) on the
power supply cord.
3. The wall outlet must have the proper polarity. If in doubt, have a competent
electrician inspect the outlet and correct if necessary.
4. DO NOT use a grounded to un-grounded receptacle adapter (where applicable).
5. Install the unit in a level position.
If the supply cord is damaged, it must be replaced by Gold Medal Products Co.,
its service agent or similarly qualified persons in order to avoid a hazard.
CAUTION
039_080614
Page 5
www.gmpopcorn.com
Page 6
Astro Pop 16oz Model No. 2023E, 2023XE, 2023XEN
OPERATING INSTRUCTIONS
Controls and Their Functions
OIL SYSTEM MASTER SWITCH
Sends power to the oil pump. The warmer/blower on the oil pump is activated. The
warmer/blower on the oil pump will keep coconut popping oil in liquid form if the doors
on the base are kept closed. It may be desirable to keep this switch on at night if you have
problems keeping the coconut oil liquefied. Coconut oil will congeal at temperatures
below approximately 76º F [24º C]. (Reference Instruction Manual for oil dispense unit.)
RED OIL DISPENSE MOMENTARY SWITCH
When pushed, this will dispense the predetermined amount of oil into the kettle.
LIGHT AND WARMER SWITCH
This switch operates the interior light and the forced air popcorn crisping system.
KETTLE MOTOR SWITCH
This switch operates the popcorn agitator motor. This switch must be on at all times when
popcorn (popped and un-popped) is present in the kettle. This switch activates the
exhaust fan.
KETTLE HEAT SWITCH
This switch turns on the heat elements located in the popcorn kettle by sending power to
the Big Eye electronic control system.
YELLOW LIGHT AND AUDIBLE SOUND
The Astro-Pop is equipped with the state of the art Big Eye electronic control that “watches
your popcorn machine” to deliver optimum popping performance. The Big Eye control will
signal the operator to:
• Load the corn and oil or
• Dump the popped corn from the kettle or
• Turn OFF the Kettle Heat if you are finished popping corn.
1
Item Part No. Model(s) Part Description Qty.
1 1
2 41031 ALL OIL PUMP SWITCH 1
3 1
4 42798 ALL LIGHTED ROCKER SWITCH 5
2
48660 2023E 125V GREEN PILOT LIGHT
48660EX 2023XE-XEN PILOT LIGHT, 250V GREEN
55039 2023E 125V AMBER PILOT LIGHT
55039EX 2023XE-XEN PILOT LIGHT, AMBER 230V
4
Page 6
3
www.gmpopcorn.com
Page 7
Kettle
Size
Popcorn
Charge
Oil
Charge
Flavacol (Salt)
16 oz.
16 oz. (473 ml)
5 oz.
(
148 ml)
1.5
Tblsp. (2
0
cc)
Astro Pop 16oz Model No. 2023E, 2023XE, 2023XEN
Popping Instructions
This section describes popping instructions for Standard (salted) popcorn.
Remember
When the Yellow Light comes ON, and Audible Signal (if enabled) is sounding,
one of the following actions should be taken:
• Load the corn and oil or
• Dump the popped corn from the kettle or
• Turn OFF the Kettle Heat if you are finished popping corn.
Amount of Popcorn and Oil
This popper is equipped with a corn, salt, and oil measure. Gold Medal recommends flavored and
colored coconut oil. Popcorn popped in coconut oil stays fresh longer and does not leave black
deposits in your kettle like other oils. Use only top quality, fresh popcorn from reputable suppliers.
Popping Standard (Salted) Popcorn
1. Turn all switches ON.
Note: When popping with coconut oil, be sure the oil is liquid. As a check, dispense oil
into a measuring cup first (should be between 4 to 5 oz.), then use that oil for
the first popping cycle.
2. When the kettle is ready (about 4 minutes), the Yellow Light and Audible Signal (if
enabled) will turn ON.
3. Lift the kettle lid and pour in the popcorn and Flavacol in the premeasured amounts
specified above. Close lid.
4. Press the “Red” Oil Dispense PB Switch to add oil. The proper amount of oil is pumped
into the kettle. The Light and Signal will turn OFF.
5. When the corn has finished popping the Yellow Light and Audible Signal will turn ON,
then gently dump the popcorn.
Note: The signal “To Dump” was factory set based on Gold Medal Products Co.
popcorn and oil. If, after 3 consecutive batches, the signal occurs before or after
popping has stopped, the signal timing must be adjusted. Have a qualified
service person adjust the signal to dump (see the Electronic Temperature
Control section).
Page 7
www.gmpopcorn.com
Page 8
Astro Pop 16oz Model No. 2023E, 2023XE, 2023XEN
6. On the final kettle of corn, turn the Kettle Heat Switch OFF just as the lids are forced
open by the popping corn. This procedure saves electricity, since the kettle has plenty
of heat, and helps eliminate smoke/odor from any oil residue that remains after
popping has stopped.
Note: When the Kettle Heat Switch is OFF, the machine will not beep on the last batch.
7. When finished popping, make sure KETTLE HEAT and KETTLE MOTOR switches are
turned OFF.
NEVER LEAVE THE HEAT ON WHEN YOU ARE NOT POPPING CORN!
Page 8
www.gmpopcorn.com
Page 9
Astro Pop 16oz Model No. 2023E, 2023XE, 2023XEN
Care and Cleaning
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
DO NOT immerse in water.
Always unplug the equipment before cleaning or servicing.
WARNING
To avoid serious burns, DO NOT touch the kettle while it is hot!
Good sanitation practice demands that all food preparation equipment be cleaned regularly (only
use non-toxic, food grade cleaners). A clean looking, well-kept machine is one of the best ways of
advertising your product.
025_020314
028_082715
Note: It is extremely important to follow all of the cleaning procedures, otherwise
parts damage and equipment failure will result. The warranty does not cover
parts that are damaged due to improper cleaning.
Daily Kettle Cleaning Instructions
CAUTION: A hot kettle will cause burns if you touch it with your hand. Allow kettle to
cool at least 1 hour before attempting to clean. DO NOT use ice or water to
cool down a hot kettle! Severe kettle damage will result!
1. When cool, wipe the outside of the kettle with a clean, soft cloth. DO NOT use oven
cleaners or abrasive materials as they will damage the kettle.
2. Every night, mix Gold Medal’s Heat’n Kleen solution (Item No. 2095), 2 tablespoons
per gallon of water. It is not necessary to use the entire gallon at once; only use
enough to fill the kettle 1/2 inch deep.
3. Turn the kettle heat ON. When the water starts to boil, turn the kettle heat OFF.
4. Allow to cool for at least 1 hour, then dump the solution into a bucket and wipe the
inside of the kettle with a clean cloth. Make sure all of the solution goes into the
bucket; do not spill any in the interior of the machine.
For an extra dirty kettle, the process may be repeated; or, after turning the kettle heat
OFF, allow solution to sit in the kettle overnight. The next morning, dump the solution
into a bucket and wipe the inside of the kettle with a clean cloth.
5. With the unit OFF and unplugged, wipe the kettle lead cord with a clean SLIGHTLY damp
cloth. DO NOT get moisture into the kettle lead-in cord, severe damage will result.
Page 9
www.gmpopcorn.com
Page 10
Astro Pop 16oz Model No. 2023E, 2023XE, 2023XEN
Daily Unit Cleaning Instructions
1. Turn machine OFF, unplug unit and allow it to cool before attempting to clean.
2. Clean all pans/accessories in order to sanitize them before each use.
3. Take a clean, SLIGHTLY damp cloth and wipe excess grease from glass and cabinet.
4. Wipe stainless steel parts with a clean cloth and cleaner designed for stainless steel,
such as Gold Medal Watchdog Stainless Cleaner (Item No. 2088).
DO NOT use oven cleaners or abrasive materials as they will damage parts of machine.
5. Clean glass panels with glass cleaner. Gold Medal Watchdog Glass Cleaner (Item No.
2588) is recommended.
Ammonia cleaners will damage plastic doors/panels. Use only non-ammonia cleaners,
such as Gold Medal Watchdog Glass Cleaner (Item No. 2588).
Page 10
www.gmpopcorn.com
Page 11
Step 1
:
Step 2:
Step 3
:
water and allow to dry overnight.
with the roof of the
Astro Pop 16oz Model No. 2023E, 2023XE, 2023XEN
Filter Cleaning Instructions
Your popcorn machine is equipped with an efficient and durable filtration system. The filter
should be cleaned every 1-2 weeks to maintain maximum efficiency.
Follow the steps below for proper filter cleaning:
The filter is located on the inside
of the popcorn machine directly
above the popping kettle.
Remove the filter by gripping
the filter itself and pulling
straight down.
Clean the filter in warm soapy
Replace the filter by putting it
into the slot and pushing
upward. Make sure the filter
frame is flush
machine (as shown above).
Page 11
www.gmpopcorn.com
Page 12
Astro Pop 16oz Model No. 2023E, 2023XE, 2023XEN
MAINTENANCE INSTRUCTIONS
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle.
DANGER
Improper installation, adjustment, alteration, service, or maintenance can
cause property damage, injury, or death. Any alterations to this equipment
will void the warranty and may cause a dangerous condition. This appliance
is not intended to be operated by means of an external timer or separate
remote-control system. NEVER make alterations to this equipment. Read the
Installation, Operating, and Maintenance Instructions thoroughly before
installing, servicing, or operating this equipment.
008_051514
014_020416
No user serviceable parts inside. Refer servicing to qualified service
personnel.
THE FOLLOWING SECTIONS OF THIS MANUAL ARE INTENDED ONLY
FOR QUALIFIED SERVICE PERSONNEL WHO ARE FAMILIAR WITH
ELECTRICAL EQUIPMENT. THESE ARE NOT INTENDED FOR THE
OPERATOR.
WARNING
011_051514
CAUTION
027_010914
Page 12
www.gmpopcorn.com
Page 13
It does not matter which
TC
goes
Remove
this
Remove
this
Control Setpoint Temperature
Overshoot
–
This is factory set,
Kettle Dump
-
This
is factory set
L1
Hot Lead
Jumper Wire A & B
Astro Pop 16oz Model No. 2023E, 2023XE, 2023XEN
Electronic Temperature Control (Domestic)
Operation
The temperature control is factory set to stop the power to the kettle when the thermocouple
reaches setpoint. This is also the ideal point to dump the popped corn out of the kettle. On the
first start-up, this is the ideal time to load the corn and oil. Therefore, if the Kettle Heat Switch is
turned ON and the buzzer is sounding, one of the following actions should be taken:
• Load the corn and oil or
• Dump the popped corn from the kettle or
• Turn OFF the Kettle Heat Switch if you are finished popping corn.
Adjustment of Electronic Control
This unit has an electronic kettle control with 2 thermocouples (TC), one for control and one for
limit. There are no mechanical thermostats in this kettle.
There are (4) factory adjustments on the control:
1. Control Setpoint Temperature – This is factory set, DO NOT adjust.
2. Signal to Dump – If you want the signal to dump to be a little sooner or later, you can
adjust the Kettle Dump potentiometer (see image below). Turn clockwise (CW) to signal
sooner, counterclockwise (CCW) to signal later.
3. The patented Overshoot circuit is tuned for the kettle, DO NOT adjust this potentiometer.
4. The Audible Signal to Dump has three options; full volume, half volume, no sound (yellow
light only). Adjustments are made by jumper positions (see image below). The unit is
shipped with full volume.
to A or B; it DOES matter that the
yellow leads go to the positive
terminals.
Audible Signal to Dump
jumper for
no sound.
jumper for
lower volume.
This is factory set, DO NOT ADJUST.
DO NOT ADJUST.
to signal when kettle is ready to
dump. Turn CW to signal sooner;
CCW to signal later. ONLY make
small adjustments if needed.
L2 Neutral Lead
for 120 VAC
Page 13
www.gmpopcorn.com
Page 14
It does not matter which
TC
goes
Remove
this
Remove
this
Control Setpoint Temperature
Overshoot
–
This is factory set,
Kettle Dump
-
This
is factory set
Astro Pop 16oz Model No. 2023E, 2023XE, 2023XEN
Electronic Temperature Control (Export)
Operation
The temperature control is factory set to stop the power to the kettle when the thermocouple
reaches setpoint. This is also the ideal point to dump the popped corn out of the kettle. On the
first start-up, this is the ideal time to load the corn and oil. Therefore, if the Kettle Heat Switch is
turned ON and the buzzer is sounding, one of the following actions should be taken:
• Load the corn and oil or
• Dump the popped corn from the kettle or
• Turn OFF the Kettle Heat Switch if you are finished popping corn.
Adjustment of Electronic Control
This unit has an electronic kettle control with 2 thermocouples (TC), one for control and one for
limit. There are no mechanical thermostats in this kettle.
There are (4) factory adjustments on the control:
5. Control Setpoint Temperature – This is factory set, DO NOT adjust.
6. Signal to Dump – If you want the signal to dump to be a little sooner or later, you can
adjust the Kettle Dump potentiometer (see image below). Turn clockwise (CW) to signal
sooner, counterclockwise (CCW) to signal later.
7. The patented Overshoot circuit is tuned for the kettle, DO NOT adjust this potentiometer.
8. The Audible Signal to Dump has three options; full volume, half volume, no sound (yellow
light only). Adjustments are made by jumper positions (see image below). The unit is
shipped with full volume.
to A or B; it DOES matter that the
yellow leads go to the positive
terminals.
Audible Signal to Dump
jumper for
no sound.
jumper for
lower volume.
This is factory set, DO NOT ADJUST.
DO NOT ADJUST.
to signal when kettle is ready to
dump. Turn CW to signal sooner;
CCW to signal later. ONLY make
small adjustments if needed.
L2 Neutral Lead
L1 Hot Lead
Jumper Wire C for 230 VAC
Page 14
www.gmpopcorn.com
Page 15
Astro Pop 16oz Model No. 2023E, 2023XE, 2023XEN
ORDERING SPARE PARTS
1. Identify the needed part by checking it against the photos, illustrations, and/or
parts list.
2. Use only approved replacement parts when servicing this unit.
3. When ordering, please include part number, part name, and quantity needed.
4. Please include your model number, serial number, and date of manufacture (located
on the machine nameplate/data plate) with your order.
5. Address all parts orders to:
Parts Department
Gold Medal Products Co.
10700 Medallion Drive
Cincinnati, Ohio 45241-4807
Or, place orders by phone or online:
Phone: (800) 543-0862
(513) 769-7676
Fax: (800) 542-1496
(513) 769-8500
E-mail: info@gmpopcorn.com
Web Page: gmpopcorn.com
Page 15
www.gmpopcorn.com
Page 16
3
9 10
Astro Pop 16oz Model No. 2023E, 2023XE, 2023XEN
Kettle Assembly – Parts Breakdown
1
2
4
14
5
16
8
18
15
17
6
4
12
13
1
11
7
Page 16
www.gmpopcorn.com
Page 17
1
55176
ALL
KETTLE LEAD ASSY
1
2
41120
ALL
REAR LID
1
3
41123
ALL
FRONT LID
1
6
47691
ALL
1/4-20 X 1 THUMB SCREW
4
7
41598
ALL
KETTLE GASKET
1
8
46311
ALL
1/4-20 SERRATED LOCK NUT
12
67014
55166E
TUBULAR HEAT ELEMENT
67014EX
55166XE
1550W HEAT ELEMENT
12
67943
ALL
#8-32 TOP LOCK NUT
2
15
41730
ALL
WOODRUFF KEY #3 1/8X1/2
1
16
47662
ALL
5/16-18 X 3/8 SQ HD SCREW
2
17
61167
ALL
THREADED BLOCK
2
Astro Pop 16oz Model No. 2023E, 2023XE, 2023XEN
Kettle Assembly – Parts List
Item Part No. Model(s) Part Description Qty.
4 41081 ALL KETTLE SHELL ASSEMBLY 1
5 47110 ALL KNOB DUMP HANDLE 1
9 67890 ALL TRANSFER PLATE 1
10 67894 ALL ELEMENT CLAMP 6
11 1
13 47393 ALL JUNCTION BOX 1
14 47707 ALL DUMP HANDLE 1
18 67892 ALL KETTLE WELD 1
Page 17
www.gmpopcorn.com
Page 18
Astro Pop 16oz Model No. 2023E, 2023XE, 2023XEN
Agitator Assembly
1
2
3
5
6
9
7
8, 4
5
Item Part No. Model(s) Part Description Qty.
1 43434 ALL AGITATOR BEARING HUB 1
2 47106 ALL NEEDLE BEARING 1
3 47060 ALL SPUR GEAR 1
4 47751 ALL SET SCREW 1/4-20 X 3/16 2
5 41093 ALL AGITATOR SHAFT ASSEMBLY 1
6 41239 ALL OIL TUBE WITH FUNNEL 1
7 41086 ALL CROSSBAR ASSEMBLY 1
8 47326 ALL SET COLLAR 1/2ID X 7/8OD 2
9 41742 ALL SET SCREW #10-32 X 3/16 1
Page 18
www.gmpopcorn.com
Page 19
3
41351
ALL
FEMALE HINGE LONG LEFT
2
4
41014
ALL
ASTRO DOOR
2
5
41017
ALL
DROP PANEL ASSEMBLY
1
6
41013
ALL
DOOR KNOB
2
9
41838
ALL
OLD MAID PAN
1
10
41349
ALL
MALE HINGE SHORT LEFT
2
11
41352
ALL
FEMALE HINGE LONG LEFT
2
12
67848
ALL
INSPECTION COVER
1
Astro Pop 16oz Model No. 2023E, 2023XE, 2023XEN
Cabinet Exterior
12
1
10, 11
7, 8
2, 3
6
4
5
9
Item Part No. Model(s) Part Description Qty.
1 41345 ALL DOME ASSEMBLY 1
2 41350 ALL MALE HINGE SHORT RIGHT 2
7 47561 ALL MAGNETIC CATCH 1
8 41340 ALL MAGNETIC CATCH BRACKET 1
13 41282 ALL CASE BOTTOM RUBBER FEET 4
13
Page 19
www.gmpopcorn.com
Page 20
6
Astro Pop 16oz Model No. 2023E, 2023XE, 2023XEN
Cabinet Interior – Hanger Assembly
1
3
12
4, 8
2
5
9
10, 11
7
Item Part No. Model(s) Part Description Qty.
1 17451 ALL ROCKER PUSH BUTTON BOX 1
2 17450 ALL 5 HOLE SWITCH BOX 1
3 69850 ALL BOX FILTER (not shown) 1
4 1
5 67194 ALL GEAR BLOCK ASSEMBLY 1
6 47262 ALL HANGER ARM FRONT 1
7 47228 ALL HANGER ARM REAR 1
8 47047 ALL LAMP HOLDER 1
9 47060 ALL SPUR GEAR 1
10 47225 ALL SET COLLAR 2
11 47226 ALL SET SCREW 2
12 62666 ALL FILTER SPRING CLIPS 2
47176 2023E 65W COATED REFLECTOR FLOOD
41979EX 2023XE-XEN 75W HALOGEN FLOOD
Page 20
www.gmpopcorn.com
Page 21
5 6
10 11
13
Astro Pop 16oz Model No. 2023E, 2023XE, 2023XEN
Corn Pan and Blower Assembly – Parts Breakdown
2
1
7
8
9
14
3
12
4
15
Page 21
www.gmpopcorn.com
Page 22
47356
2023E
115V MOTOR WARMER
47669
2023XE-XEN
230V MOTOR WARMER
2
61021
ALL
FEMALE CORD
1
44073
2023E
STRAIN RELIEF
2
82220
2023XE-XEN
STRAIN RELIEF
2
10
47358
ALL
RUBBER PAD
1
11
47985
ALL
TOP MOUNTING ANGLE
1
Astro Pop 16oz Model No. 2023E, 2023XE, 2023XEN
Corn Pan and Blower Assembly – Parts List
Item Part No. Model(s) Part Description Qty.
1 1
3 61020 ALL MALE CORD 1
4 41113 ALL BLOWER WHEEL 1
5 1
6 47385 ALL THERMOSTAT WARMER 1
7 1
8 41838 ALL OLD MAID PAN 1
9
12 47542 ALL TUNNEL COVER WELD ASSEMBLY 1
13 47545 ALL WARMER CHASSIS ASSEMBLY 1
14 41879 ALL CORNER COVER 1
15 41102 ALL BOTTOM CORN PAN 1
47355 2023E 120V, 400W HEAT ELEMENT
47732 2023XE-XEN 240V, 400W HEAT ELEMENT
47563 2023E WARMER BLOWER ASSEMBLY
47563EX 2023XE-XEN WARMER BLOWER ASSEMBLY
Page 22
www.gmpopcorn.com
Page 23
2
14
For Power Cord
Astro Pop 16oz Model No. 2023E, 2023XE, 2023XEN
Dome Interior View – Parts Breakdown
1
12
15
8
3
10, 13
4
16
5
9
6
17
11
18
(not shown), see
Parts List
Page 23
7
19
www.gmpopcorn.com
Page 24
1
47047
ALL
LAMP HOLDER
1
48018
2023E
120V 60CY EXAUST BLOWER
48037
2023XE-XEN
220V 50CY EXAUST BLOWER
47038
2023E
120V KETTLE DRIVE MOTOR
47067
2023XE-XEN
230V KETTLE DRIVE MOTOR
4
41001
ALL
TEMPERATURE CONTROL
1
55219
2023E
30A DPST 120V RELAY
55219EX
2023XE-XEN
RELAY, 30A DPST 240V
62306
2023E
KETTLE RECEPTACLE ASSEMBLY
62306EX
2023XE-XEN
RECEPTACLE ASSY
47364
2023E
15A CIRCUIT BREAKER
48659
2023XE-XEN
10A CIRCUIT BREAKER
8
47208
ALL
TERMINAL BLOCK
1
9
89087
ALL
240VAC TRANSIENT FILTER
2
41640
2023E
8W 120V FOIL ELEMENT
41640EX
2023XE-XEN
8W 230V FOIL ELEMENT
11
47199
ALL
BLOWER PLUG AND CORD
2
49480
2023E
LIGHT SHIELD CONICAL
49584
2023XE-XEN
RECESSED LIGHT COVER
13
41047
ALL
OIL LINE TUBING
5.42'
14
67841
ALL
EXHAUST BLOWER BOX
1
15
41526
ALL
DOME SPACER
2
16
67842
ALL
TEMPRATURE CONTROL MOUNT PLATE
1
17
77475
ALL
MOUNT PLATE
1
47601
2023E
POWER SUPPLY CORD
42369
2023XE-XEN
EXPORT POWER SUPPLY CORD
19
41499
ALL
WIRE HARNESS OIL PUMP
1
47026
2023E
STRAIN RELIEF (Not Shown)
41735
2023XE-XEN
STRAIN RELIEF (Not Shown)
21
47290
2023E
POWER SUPPLY RECPT (Not Shown)
1
22
47377
2023E
POWER SUPPLY RECPT COVER (Not Shown)
1
Astro Pop 16oz Model No. 2023E, 2023XE, 2023XEN
Dome Interior View – Parts List
Item Part No. Model(s) Part Description Qty.
2 2
3 1
6 1
7 1
25
10
18 1
20 1
1
112
Page 24
www.gmpopcorn.com
Page 25
Astro Pop 16oz Model No. 2023E, 2023XE, 2023XEN
Lighting Assembly – Parts Breakdown
1
2
11
3
5
10
9
4
8
6
9
7
11
Page 25
www.gmpopcorn.com
Page 26
1
41301
LED
LED POPCORN SIGN
1
2
55379
LED
1W LED STRIP
2
3
55394
LED
24VDC 20W POWER SUPPLY
1
5
67417
NEON
NEON SIGN COVER
1
6
55231
NEON
12V POWER SUPPLY
1
7
67517
NEON
NEON SIGN BOTTOM BRACKET
2
9
67438
NEON
EXTRUSION
2
10
69708
NEON
LED POPCORN SIGN
1
11
47562
ALL
WIRE HARNESS
1
Astro Pop 16oz Model No. 2023E, 2023XE, 2023XEN
Lighting Assembly – Parts List
Item Part No. Model(s) Part Description Qty.
4 67420 NEON END CAP (Not Shown) 2
8 45003 NEON NEON SIGN ASSEMBLY 1
Page 26
www.gmpopcorn.com
Page 27
Astro Pop 16oz Model No. 2023E, 2023XE, 2023XEN
WIRING DIAGRAM
Model 2023E
Page 27
www.gmpopcorn.com
Page 28
Astro Pop 16oz Model No. 2023E, 2023XE, 2023XEN
WIRING DIAGRAM
Model 2023XE, 2023XEN
Page 28
www.gmpopcorn.com
Page 29
10700 Medallion Drive, Cincinnati, Ohio 45241
-
4807 USA
Phone:
(800) 543
-
0862
Fax: (800) 542
-
1496
Astro Pop 16oz Model No. 2023E, 2023XE, 2023XEN
WARRANTY
Gold Medal Products Co. warrants to the original purchaser each item of its manufacture to
be free of defects in workmanship and material under normal use and service. Gold Medal
Products Co.’s obligation under this warranty is limited solely to repairing or replacing parts,
f.o.b. Cincinnati, Ohio, which in its judgment are defective in workmanship or material and
which are returned, freight prepaid, to its Cincinnati, Ohio factory or other designated point.
Except for “Perishable Parts” on specific machines, the above warranty applies for a period
of two (2) years from the date of original sale to the original purchaser of equipment when
recommended operating instructions and maintenance procedures have been followed. These
are packed with the machine. Parts warranty is two (2) years, labor is six (6) months.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR
IMPLIED, AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR PART,
INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY. THERE ARE
NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE
HEREOF. In no event shall Gold Medal Products Co. be liable for special, incidental or
consequential damages. No claim under this warranty will be honored if the equipment covered
has been misused, neglected, damaged in transit, or has been tampered with or changed in any
way. No claim under this warranty shall be honored in the event that components in the unit at
the time of the claim were not supplied or approved by Gold Medal Products Co. This warranty
is effective only when electrical items have been properly attached to city utility lines only at
proper voltages. This warranty is not transferable without the written consent of Gold Medal
Products Co.
The term “Original Purchaser” as used in this warranty shall be deemed to mean that person,
firm, association, or corporation who was billed by the GOLD MEDAL PRODUCTS CO.,
or their authorized distributor for the equipment.
THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL
PURCHASER FIRST CALLS GOLD MEDAL PRODUCTS CO. AT 1-800-543-0862 TO
DISCUSS WITH OUR SERVICE REPRESENTATIVE THE EQUIPMENT PROBLEM,
AND, IF NECESSARY, FOR INSTRUCTIONS CONCERNING THE REPAIR OR
REPLACEMENT OF PARTS.
NOTE: This equipment is manufactured and sold for commercial use only.
(513) 769-7676 (513) 769-8500
© 2016 – The text, descriptions, graphics, layout, and other material in this publication are the exclusive property of
Gold Medal Products Co. and shall not be used, copied, reproduced, or published in any fashion, including website
display, without its express written consent.
gmpopcorn.com
Page 29
www.gmpopcorn.com
Loading...