Gold medal 3030, 3030SR, 3040, 3040SR User Manual [ru]

Part No. 42147

THE BREEZE®

Domestic and Export

Instruction Manual

Models 3030, 3030SR, 3030EX, 3040, 3040SR

Cincinnati, OH 45241-4807 USA

The Breeze

2 Models: 3030, 3030SR, 3030EX, 3040 and 3040SR

The Breeze

Installation Instructions

Inspection of Shipment:

After unpacking, check thoroughly for any damage which may have occurred in transit.
Claims should be filed immediately with the transportation company. The warranty
does not cover damage that occurs in transit or damage caused by abuse or
consequential damage due to the operation of this machine, since it is beyond our control.

Your Floss Machine warranty is described on the back page of this manual. This does
NOT cover the motor bearings, since they can be damaged by the operator.

Electrical Requirements:

The following power supply must be provided:

Model No. 3030, 3030SR, 3040 and 3040SR: 120 VAC, 60 Hz, 15 Amps
Model No. 3030EX: 240 VAC, 50 Hz, 15 amps

.

Your electrician must furnish sufficient current for proper machine operation. We
recommend this floss machine be on a dedicated and circuit protected line. Failure to wire
properly will void the warranty and can result in damage to the heat elements, motor and
etc.

It is Gold Medal Products Company’s recommendation that this machine be plugged directly

into a wall outlet. The use of extension cords is not recommended due to safety concerns
and the floss machine’s performance may be sacrificed/reduced.

Before You Plug in Machine

Remove all padding and restraints.

Turn the two shipping knobs located around the motor mount casting counter-clockwise.
This will allow the motor mount casting to “float” freely on the springs. Note: This step
Is not necessary for the 3040SR.

3 Models: 3030, 3030SR, 3030EX, 3040 and 3040SR

The Breeze

Operating Instructions
Controls and their Functions:

Main Switch - Turns motor "on" or "off" and supplies voltage to the heat switch.

Heat Switch - Turns voltage to the heating element "on" or "off."

Heat Control (except Accu-Breeze)- Increases or decreases voltage to heating element

using a graduated dial.

Sugar for Your Cotton Candy

The easiest way to make sure you have the right texture sugar, with proper flavor and colors, is to
use GOLD MEDAL FLOSSUGAR. FLOSSUGAR gives good, rich colors and flavors, and does not
exceed the color limitations imposed by the Food and Drug Administration. FLOSSUGAR comes in
sealed, plastic-coated cartons with handy pouring spouts for filling. If you use your own flavors in
cotton candy, make sure they are not gum or starch based; these materials burn on the ribbons.

4 Models: 3030, 3030SR, 3030EX, 3040 and 3040SR

The Breeze

Heat Control Setting Test

1. Follow the guidelines described on page 3 for supplying power to machine.

2. With main switch still OFF, fill floss head. Always fill it 90% full with sugar. This 90% level
is necessary to obtain a balanced condition in the floss head. DO NOT OVERFILL!
Excessive vibration will occur if overfilled. Before turning the power on, manually turn the
head to balance out the sugar. This will eliminate excessive vibration of the head.

3. Turn MAIN SWITCH and HEAT SWITCH "ON." Note: Steps 4 – 8 do not apply to the 3040
or 3040SR.

4. Turn heat control knob clockwise to maximum setting to initiate the fastest possible warm
up.

5. The machine should start making floss in about 45 seconds. When the unit starts making
floss, you must reduce the heat setting. Turn the heat control knob counter clockwise to
eliminate smoking.

6. Once you find the ideal setting for the HEAT CONTROL, operate with the setting near this
position each time.

7. When finished making floss, run the floss head completely empty of sugar.

8. Turn the heat control dial to the maximum position, and allow the machine to run for
approximately 3-4 minutes. This will burn any excess sugar out of the head, and prevent
any excess carbon build- up.

9. Turn the heat switch “off” and allow the motor to run for 1-2 minutes to allow the floss head
to “cool down”.

10. Turn the motor switch off and allow the motor to come to a complete stop.

5 Models: 3030, 3030SR, 3030EX, 3040 and 3040SR

The Breeze

Installation of Floss Stabilizer

1. 2.

3. 4.

6 Models: 3030, 3030SR, 3030EX, 3040 and 3040SR

The Breeze

Whirl Grip-Clip Installation Instructions

The whirl grip-clip has been designed to provide better air flow by keeping the
whirl grip (netting) off the floss pan.

To install, please follow these simple steps:

1. Insert the hooked side of the clip into the whirl grip-approximately (2) holes down from the
top, inserting from the back-as shown below.

2. Push the whirl grip through, leaving about (5) spaces in-between, and re-insert through the
back side of the whirl grip.

3. Continue this process with all (6) clips, keeping equal spacing around the pan, and slide
the long flat side of the clip down the outside of the floss pan.

7 Models: 3030, 3030SR, 3030EX, 3040 and 3040SR

The Breeze

Making Floss

Pick a cone; if it sticks in the stack of cones, twist it off the stack.
Hold an inch or two of the pointed end of the cone between two fingers and a thumb.

With a light flicking action, roll cone in the web of floss building up in the pan. Lift the
cone up with the ring of floss attached and rotate the cone to wrap the floss. DO NOT
roll floss while the cone is inside the pan. This will pack the floss too tightly.

If the floss fails to stick to the cone, pass the cone near the spinner head to pick up a

“starter” of melted sugar. Lift the cone out of the pan and wrap the floss with a "figure

eight" movement of the hand. This leaves giant pockets and makes the final product
appear larger. Make sure room humidity is not too high, or product will be "heavy".

1. Grip cone as shown. 2. Break into web of 3. Wind the sugar 4. Lift web of floss from the

floss with the cone. onto the cone. pan and roll onto the cone.

5. 6. 7. 8.

 DO NOT put hands or objects in rotating spinner head.
 DO NOT fill Spinner Head with sugar while it is rotating.
 Operator should ALWAYS wear eye protection.
 DO NOT put hands near rotating spinner head.

 Use ONLY floss cone to collect cotton candy.

8 Models: 3030, 3030SR, 3030EX, 3040 and 3040SR