Goldline GLDUAL 704 BZNG-Cast, GLDUAL 4 BZNG-Cast, GLDUAL 5 BZNG-Cast, GLDUAL 704 BZLPG-Cast, GLDUAL 4 BZLPG-Cast Installation Instructions & Use & Care Manual

4 BURNER GAS HOBS

4 BURNER GAS HOBS 5 BURNER GAS HOBS

GLDUAL 704 BZNG-Cast GLDUAL 4 BZNG-Cast GLDUAL 5 BZNG-Cast
GLDUAL 704 BZLPG-Cast GLDUAL 4 BZLPG-Cast GLDUAL 5 BZLPG-CAST
GLDUAL 704 WZNG-Cast GLDUAL 4 WZNG-Cast GLDUAL 5 WZNG-Cast
GLDUAL 704 WZLPG-Cast GLDUAL 4 WZLPG-Cast GLDUAL 5 WZLPG-Cast

INSTALLATION INSTRUCTIONS (FOR FITTERS ONLY)

&

USER AND OPERATOR INSTRUCTIONS

Installation must be in accordance with manufacturer’s instruction, relevant Gas

Fitting Regulations or AS5601 – “Gas Installation” regulations.
These instructions should be read carefully prior to initial use and retained in a safe

place in order that full advantage can be taken of the features of your HOB
COOKER.

REMINDER:

ANY SERVICING AND INSTALLATION OF THE HOTPLATE

MUST BE CARRIED OUT BY AN AUTHORIZED PERSON.

ANY QUERIES SHOULD BE FORWARDED TO:

MANUFACTURER: A’VARD INDUSTRIES P/L.
ADDRESS: 58-60 Quantum Close, South Dandenong, Victoria 3175, Australia.
TEL: 61 3 9799 9660
FAX: 61 3 9799 9662
WEBSITE: www.goldlinecorp.com.au

Goldline GLDUAL manual April 2015 2

Goldline GLDUAL manual April 2015 1

CUT OUTS

INSTALLATION INSTRUCTIONS

DATA PLATE DETAILS:
The data plate is located on the tray floor.

CHECK THAT THE DATA PLATE SHOWS THAT THE APPLIANCE IS SUITABLE FOR THE
AVAILABLE GAS SUPPLY. IMPORANT: VERIFY GAS TYPE WITH LOCAL GAS
NETWORK OPERATOR BEFORE CONNECTION OF THIS APPLIANCE.

Model GLDUAL 4

Diagram A

Tray Dimensions (in mm)

Diagram B

Cut-Out (in mm)

Diagram A

Tray Dimensions (in mm)

Diagram B

Cut-Out (in mm)

Model

GLDUAL 704

Model GLDUAL 5

Diagram A

Tray Dimensions (in mm)

Diagram B

Cut-Out (in mm)

3 Goldline GLDUAL manual April 2015

1. Room Ventilation
This cooktop must be installed in a room that has permanent ventilation to effect
the correct operation of the appliances and also to provide adequate ventilation.
This airflow must exceed 20m³ via permanent vented openings in the walls of the
room and these must have a section of 100cm² minimum. They must be
constructed in a manner so as to avoid any possible blockages. The airflow can
also be drawn indirectly from an adjacent room provided it complies with any local
regulations to vent any fumes outdoors.

Not for use in Marine craft, caravans or Mobile homes unless
fitted with safety device.

2. Before installing the appliance check that the location provides the required clearances

from combustible materials and if necessary provide protection to adjacent surfaces as
required by the regulations. Make provision for the gas supply to be connected in the
position shown in D

iagram

A.

3. Cut the opening in the bench top to the dimensions shown in diagram B.

4. Remove the hotplate from the carton.

5. Install the hotplate in the cut-out (see diagram B on page 2).

Note:

If clearance between side and rear walls and periphery of the burner is less than 250mm,
the walls must be protected with a non-combustible material. The protection must extend
a minimum distance of 450mm above the burner. Horizontal surfaces less than 750mm
vertically above the hotplate must also be protected.

6. Ensure that gas and electrical outlet are accessible with the appliance installed. The
gas connection to the regulator is 1/2” BSP. Please ensure gas supply line to the
appliance is of adequate length to allow sufficient withdrawal of appliance for service or
disconnection. The connection must be annealed copper pipe or flexible hose (if
permissible by local authority).

Note:
The cook top must be installed with provision to allow the gas to be turned off and

disconnected for servicing

and r

emoval of the appliance as required from gas supply.

7. Use a spanner at the flat area provided to hold the regulator firmly, when making the

join. Refer diagram below.