GOLDEN PRIME TECHNOLOGIES JMG-PULP 500, MG-QUIXI 500, JMG-BLISS 500, MG-QUIXI 550 PREMIUM, MG-QUIXI 600 Instruction Manual And Warranty Card

Juicer Mixer Grinder

&

Mixer Grinder

INSTRUCTION MANUAL

CUM

WARRANTY CARD

Juicer Mixer Grinder & Mixer Grinder

JUICER MIXER GRINDER

JMG-BLISS 500 | JMG-PULP 500 | JMG-PULP +500

MIXER GRINDER

MG-QUIXI 500 | MG-QUIXI 550 PREMIUM

MG-QUIXI 600 | MG-QUIXI 750

Dear Customer,

Welcome to the world of Golden Prime Home Appliances.

GP brings this amazingly versatile home appliance which will reduce your kitchen drudgery. The Juicer Mixer Grinder / Mixer Grinder is a great time saver and a convenient gadget.

This booklet will help you to understand and use your JMG properly. It gives you the required instructions on its operation and care.

CONTENT

Precautions .................................................3

Electrical Requirement .............................3

Know Your Juicer Mixer Grinder .............4

Technical Specications ....................4

How to Assemble the Jar ..................6

Know Your Mixer Grinder .........................7

Technical Specications ....................8

How to Assemble the Jar ..................9

Usage of Control Panel ......................9

Motor Overload Protector (OLP) ......9

Juicer Mixer Grinder/Mixer Grinder .... 10

Instruction For Use .......................... 10

Instruction For Cleaning ................. 11

Important Safeguards ..................... 11

Notes ......................................................... 12

Terms & Conditions................................ 14

Warranty Card ......................................... 15

PRECAUTIONS

• Read the instructions carefully before using the Juicer Mixer Grinder (JMG)/Mixer Grinder (MG).

• Place the your JMG/MG on an even platform at a convenient height so that the ingredients under operation can be easily seen.

• Have sucient space around the JMG/MG to keep the various items required. Also ensure that the JMG/MG is placed 6 inches away from the wall.

• Keep the JMG/MG away from heat and sunlight.

• The JMG/MG operates at optimum eciency at the specied voltage. Wide variations in voltage may affect the performance of the JMG/MG.

• Clean the oil traces inside the jar before rst use.

• Do not run the mixer without load.

• Ensure that the JMG/MG housing is tted properly on to the motor housing before operation.

• Fix the jar to the base unit by turning it clockwise. Make sure it is rmly locked in position prior to usage.

• Never insert your hand/spatula/spoon when the JMG/MG is in operation.

• Since the blades are quite sharp, be careful while changing them.

• Use only lukewarm water to clean your JMG/MG.

3

ELECTRICAL REQUIREMENT

• Check that the voltage on the rating plate of your appliance corresponds with your house electricity supply which must be AC.

IMPORTANT NOTES:

1. GP products are intended for household use only.

2. Parts illustrated in this use and care manual are indicative only, parts provided with the products may differ with illustrations.

3. Specications are subject to change without notice.

Juicer Mixer Grinder & Mixer Grinder

KNOW YOUR JUICER MIXER GRINDER

7

11

10

1

Mix

2

3

2

4

5

No Part Name No Part Name

1 Main Body 8 Bottom Pad

2 Bottom 9 Food Pusher

3 Juicer Cover 10 Blender Jar

4 Power Cable 11 Blender Jar Lid

5 Rotary Knob 12 Dry Grinding Jar

6 Swing Locks 13 Dry Grinder Jar Lid

7 Spout Cover

9

3

6

13

12

8

TECHNICAL SPECIFICATIONS

MODEL JMG-BLISS 500 JMG-PULP+500 JMG-PULP 500

VOLTAGE 220-240V

WATTAG E 500W

5

SPEED CONTROL 3 Speed Piano Switch with Incher Facility

RPM (Approx) 18500 19000 18000

MAIN CORD 1.5 mtr Long, 2 Pin 1.5 mtr Long, 3 Pin 1.5 mtr Long, 2 Pin

PROTECTION Class II

MOTOR INSULATION Universal Class - B

MATERIAL

HOUSING High quality ABS Plastic

JAR LIQUIDISER SAN

JAR GRINDER Stainless Steel

CHUTNEY JAR N/A Stainless Steel N/A

CAPACITY

LIQUIDISER JAR 1500 ml

3 Speed Control with

Incher (Rotary) for

Momentary Operation

JAR GRINDER 1000 ml

CHUTNEY JAR N/A 400 ml N/A

Juicer Mixer Grinder & Mixer Grinder

HOW TO ASSEMBLE THE JAR

JUICER JAR

1. Slide the online pulp container

into the juicer body.

4. Place the juicer cover onto the juicer body diagonally as shown in

the gure, then push it down.

2. Place the juicer casting on the basic unit.

5. Lock the clamps on both sides of the juicer body.

BLENDER JAR / GRINDER JAR

3. Place the lter mesh into the

body and push down slightly so that the mesh sits and locks the lower coupler of the basic unit. If necessary, rotate the mesh a little till it sits.

6. Plug the cord in and the juicer is ready to use.

1. Place the grinder jar on the basic motor unit and turn it in a clockwise direction till it locks in place.

2. Put the cover on the jar and place

your hands rmly on the cover.

3. Plug the cord into the mains. Now run the jar on the incher / whipper speed for 1 second to see if the jar

has t properly.

KNOW YOUR MIXER GRINDER

7

No Part Name No Part Name

1 Main Body 7 Flat Lid for Dry/Wet Grinding Jar

2 Speed / Incher Selector Knob 8 Dry/Wet Grinding Jar

3 Liquidising Jar 9 Jar Base

4 Dome for Liquidising Jar 10 Chutney Jar Lid

5 Dome cap for Liquidising Jar 11 Chutney Jar

6 Jar Handle

Juicer Mixer Grinder & Mixer Grinder

TECHNICAL SPECIFICATIONS

MODEL MG-QUIXI 500

VOLTAGE 220-240V

WATTAG E 500W 550W 600W 750W

SPEED CONTROL 3 Speed Control with Incher (Rotary) for Momentary Operation

RPM (Approx) 19,500 19,800 20,500 21,000

MAIN CORD 1.5 mtr Long, 2 Pin

PROTECTION Class II

MOTOR INSULATION

HOUSING High quality ABS Plastic

JAR LIQUIDISER Stainless Steel

JAR GRINDER Stainless Steel

MG-QUIXI 550

Premium

Universal Class B

MATERIAL

MG-QUIXI 600 MG-QUIXI 750

1.5 mtr Long, 3 Pin

CHUTNEY JAR Stainless Steel

CAPACITY

LIQUIDISER JAR 1200 ml 1500 ml

JAR GRINDER 750 ml 1000 ml

CHUTNEY JAR 350 ml 450 ml

1

2

4

HOW TO ASSEMBLE THE JAR

3

1. Hold the jar in one hand and check if the blade moves freely and rotates (g. 1).

2. Place ingredients in the Steel Jar. Cover the Jar with dome/lid. Place the jar on the basic unit, press

it slightly downward and then turn it clock wise to lock it in the top body socket (g. 2)

3. Plug in. Support cover gently by hand (g 3) and switch on using the slowest speed (position 1 off switch).

4. Switch off after operation. For unlocking the jar, press the jar downward and then turn it anticlock

wise (g. 4) and lift the jar from the basic unit.

USAGE OF CONTROL PANEL

The control panel is a 3 speed rotary switch with an in built 4” inching position for whipping operation. For whipping, turn the rotary switch in the anticlockwise direction.

9

2

1

0

4

3

0

2

1

4

3

0

2

1

4

3

1

0

4

MOTOR OVERLOAD PROTECTOR (OLP)

The JMG/MG is tted with a heavy duty universal motor using a

winding wire that can withstand extremes of temperatures. It is however possible that the mixer motor may get overloaded when you attempt to grind quantities in excess.

The motor of the JMG/MG is protected by a resetting type Over Load Protector (OLP).

In case of overloading, the OLP disconnects the power supply to the motor, in such an event, switch off the supply. Remove the excess the load or add water to the ingredients.

Wait for a few minutes. Reset the OLP located below the base plate and restart the mixer.

2

3

0

2

1

4

3

Juicer Mixer Grinder & Mixer Grinder

JUICER MIXER GRINDER/MIXER GRINDER

INSTRUCTIONS FOR USE

JUICER (In JMG only)

1. Mount the juicer housing cum pulp chamber on the basic unit.

2. Place the juice mesh into the juicer body. Ensure that the mesh is placed properly and locks the

lower couple of the basic unit. Please check its tment by rotating it by hand to see if it is rotating

freely. Don’t apply any undue pressure.

3. Slide the juice Sport (outlet) cover in position and press.

4. Mount the juice cover onto the juice body and lock the clamps, plug the cord in and the juicer

is ready to use. Press the switch marked ‘Pulse’ to check if the lter mesh assembly is properly

seated with the lower couple of the basic unit. The mesh should spin evenly without wobbling.

5. Wash ingredients and cut in small pieces to t feeder opening and place a glass under the spout. Set switch to position ‘1’. Push Ingredients into feeder with the food pusher.

6. For short operations, turn the speed control to pulse position.

7. Once the juicing operation is over, press the ‘0’ button and unplug the unit.

LIQUIDIZING JAR - BLENDING

1. The minimum capacity of the jar is 1/3 of the jar and maximum capacity is 2/3.

2. Fill the jar with solids to be liquidized.

3. Fit the jar onto the main unit.

4. Add water, if needed.

5. Cover the jar with the lid.

6. Now switch on the mixer for a minute to get nely blended juices and purees.

GRINDER JAR - WET/DRY

1. This jar can be used for grinding black pepper, roasted coffee seeds, turmeric, coriander, red chillies, etc.

2. The jar should not be lled more than half of its total capacity.

3. Ensure that the jar is absolutely clean and dry.

4. Fill the jar with the ingredients.

5. Cover the jar with the lid and t on the main unit.

6. While grinding turmeric, break it into smaller pieces before you start grinding.

7. If the ingredients need to be stirred during wet grinding of rice and dal batter, stop the mixer, insert the spatula and stir.

CHUTNEY JAR

1. This jar can be used for preparation of chutneys.

2. Inch to 5-7 times to powder ingredients.

3. Then add water as required.

4. Cover the jar with the lid and t on the main unit.

INSTRUCTIONS FOR CLEANING

JUICER

1. Before putting on or taking off any part, make sure that the juicer in unplugged.

2. Release the swing lock downwards and life the juicer cover.

3. Remove juicer mesh assembly by pulling it up from the base of the juicer body.

4. Remove the spout cover from the juicer body.

5. Remove the pulp collected in the pulp collector of the juicer body.

6. Clean the juicer mesh under running water.

7. The motor must always be kept dry. Use a damp cloth to clean the motor housing.

8. Do not use abrasive cleaners or scouring pads on the appliance.

9. Dry all the parts after cleaning.

10. Reassemble all parts in proper order and store the appliance in dry place.

JARS - LIQUIDIZING/ WET GRINDING/DRY GRINDING

1. After use, ll 1/3rd of the jar with lukewarm water, add a little mild liquid soap/detergent.

2. Fix the lid & run machine for about 30 sec at the lowest speed. This will clear out all the remaining particles.

3. Wash the jar in running tap water and wipe the screw area with a dab cloth and then with dry cloth.

11

IMPORTANT SAFEGUARDS

The use of any electrical appliance requires the following Safety rules:

• Always unplug the machine from the power outlet before putting on or removing the blades, before cleaning.

• Never touch the blades or disc during operation to avoid personal injury or damage to the machine.

• Before using the JMG/MG, ensure that the jar is properly assembled.

• Do not use your JMG/MG without dome lids in place over the jars.

• Do not use your JMG on wet surfaces nor immerse the cord or plug in water to prevent electrical hazards.

• Do not run the JMG without any load nor burden the motor with loads heavier than specied.

• Never place any cloth or plastic sheet under the basic unit, as it may get sucked up and block the ventilation holes in base during operation.

• Never use attachments that are not recommended by manufacturer.

• The appliance should not be run for more than 30 minutes at a stretch normally. Stop for 10 minutes before starting again. When hot air comes out of the ventilator, switch off for a while. The Grinder jar may heat up during dry grinding due to friction. Let it cool for few seconds. And then remove.

• Do not attempt to repair the appliance at home or allow any unauthorised person to do it. Take it to the nearest authorised service centre instead.

• Do not place on or near a hot gas or electric burner or in a heated oven.

• Do not allow children to handle the appliance or leave the appliance unsupervised.

• Do not use the Liquidiser Jar for dry/wet grinding, grating, chopping or mincing functions.

Juicer Mixer Grinder & Mixer Grinder

NOTES:

............................................................................................................................................................................

NOTES:

............................................................................................................................................................................

13

............................................................................................................................................................................

Juicer Mixer Grinder & Mixer Grinder

TERMS & CONDITIONS

This Warranty is not valid in case of the following:-

• Normal wear and tear of the parts.

• Damage due to chipping, peeling, plating and denting.

• Any repair work carried out by persons other than done by authorised service centre.

• Damage arising due to running of the appliance on alternate source of power such as inverter.

Generator or any such auxiliary power supply aid resulting in variation/uctuating voltage.

• Breakage or damage to components made of ABS, SAN, Bakelite, Glass; and plastic/rubber parts, power cord, bulbs and surface coating is not considered in warranty.

• Product if used for commercial purposes.

• The serial number of the product has been removed obliterated or altered with.

• The warranty specically excludes any problems arising out of mishandling, wilful damage, improper storage of the product and in the case of its parts, if they have not been maintained and operated strictly in accordance with the instruction manual.

• Warranty card/invoice/cash memo/or proof of purchase is not available at time of showing product for inspection to engineer. Engineer needs proper proof of purchase to calculate warranty of the product.

WARRANTY CARD

GP product is warranted against any manufacturing fault or functioning failure on product from the date of purchase for a period of 2 years, only on production of valid proof of purchase.

In case of any defect or failure, user of the product must carry the product with its accessories to the nearest authorised service centre.

Date Of Purchase ______ / ______ /_________

Product Name: __________________________________________________________________________

Invoice No.: ______________________ Model No.: ______________________

15

Dealer’s Name & Address ________________________________________________________________

_________________________________________________________________________________________

Customer Name & Address ______________________________________________________________

_________________________________________________________________________________________

Dealer’s Stamp & Sign

Serial No.: __________________________

Ean Code: ___________________________

GOLDEN PRIME TECHNOLOGIES

Marketed by:

REMAIN PRIME TECHNOLOGIES PVT LTD

+91 9700 800 900 | hello@goldenprime.co.in | www.goldenprime.in

/gpappliances /gpappliances /gpappliances

Remain Prime reserves the right to amend or modify the specications & features

at any time, as & when required without any prior notication. Images displayed here

may vary from the actual product. Features vary by products.

GOLDEN PRIME TECHNOLOGIES JMG-PULP 500, MG-QUIXI 500, JMG-BLISS 500, MG-QUIXI 550 PREMIUM, MG-QUIXI 600 Instruction Manual And Warranty Card

Specifications and Main Features

Frequently Asked Questions

User Manual