INSTALLATION INSTRUCTIONS
Fixture Name: AUTUMN TWILIGHT 9903-WSC MSI
For Wall Mount Light Fixture
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
HANGING THE FIXTURE (Fig.1)
1. Carefully remove the new fixture from the carton
and the yellow parts bag. Check that all parts are
included as shown in the illustration and parts list.
2. Shut off power at the circuit breaker and remove
the old fixture from wall, including the old
mounting strap.
3. The Mounting Strap (A) contains several pairs of
threaded holes, find the pair of holes that match
the holes spacing in your fixture Back Plate (D) and
thread the two Fixture Mounting Screws(C) half
way into the Fixture Mounting Strap (A).
4. Place the Mounting Strap (A) over the Junction
Box so the Fixture Mounting Screws(C) are vertical
or horizontal, as required by the fixture type.
5. Attach the Fixture Mounting Strap (A) to the
Junction Box using the two Mounting Screws (B).
Tighten the Screws (B) securely with screwdriv er.
CONNECTING THE WIRES(Fig.2)
6. Attach the power supply wires to the fixture lead
wires by connecting BLACK to BLACK (or SMOOTH)
and WHITE to WHITE (or RIBBED).
7. Attach the GROUND wire (GREEN or COPPER)
from the Junction Box and the fixture Ground wire
to the green Ground Screw on the Mounting
Bracket (B) or connect both wires together using
the correct size of wire connectors.
NOTE: Twist the wires together in the same direction
you twist the wire connector onto the wires.
8. Tuck these wire connections neatly into the
Junction Box.
FINISHING THE INSTALLATION(Fig.3)
9. After tucking these wire connections neatly into
the Junction Box and place the fixture Back Plate
(D) over the two Mounting Screws (C) and secure
the Back Plate (D) against the wall by threading
two Deco Nuts (E) over the two Mounting Screws
(C) until tight as shown on Fig.3.
10. Install crystals as per the fixture assembly
instructions.
YOUR INSTALLATION IS NOW COMPLETE. RETURN
POWER TO THE JUNCTION BOX AND TEST THE FIXTURE.
Fig. 1
Fig.2
FIXTURE WIRES
SMOOTH
(or Black)
RIBBED
(or White )
BARE COPPER
(or Green)
Fig.3
JUNCTION BOX
JUNCTION BOX
E
D
B
A
C
HOUSE WIRES
BLACK
WHITE
(Neutral)
GREEN
round
C
(Hot)
F For Customer Service, contact the place of purchase to arrange for replacement parts.
CSA055303WALG2
PARTS & ASSEMBLY SHEET
Fixture Name: AUTUMN TWILIGHT 9903-WSC MSI
This fixture assembled PO: Date:
Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are missin
damaged, please note on this sheet and contact the place of purchase to arrange for replacement parts.
Company Name:______________________Co Account#:__________
PARTS LIST
Mounting Strap
Φ102 ㎜ 1ea
Wire Connectors
Orange 3ea
Crystal Leaf
PT-LEAF-9903 MSI
8ea W27*H65 ㎜
below to be filled out by retailer
Green Screw
G8/32*H8 ㎜ 1ea
Hex Nut
G5/32*H4 ㎜ 2ea
Bulbs
3ea Halogen,
Type G4 20W
Mounting Screws
H32
㎜
2ea H38㎜2ea
Deco Nut
Φ12 ㎜ 2ea
Part Needed ______________________________ Quantity _________________________________
Part Needed ______________________________ Quantity _________________________________
Reason why (missing, scratched, broken glass, bent, bad finish)
Comments __________________________________________________________________________
FIXTURE ASSEMBLY INSTRUCTIONS
Read and review installation instruction sheet
9903-WSC MSI
Fig.1
before assembling the fixture
or
1. Open bag on the arm and carefully arrange the
bead strings.
2. Screw Crystal Leaf (A) on the arm.
Hold carefully by the metal base to prevent the
crystal from cracking.
3. Install the light bu lbs in accordance with the
fixture's specification.
Bulb note: Use a tissue or paper towel to hold t he
bulb and push down into socket. Oils or dirt can
cause the bulb life to shorten. Rubbing alcohol is
recommended to clean the bulbs if dirty.
(DO NOT EXCEED THE MAXIMUM WATTAGE RATING!)
A
4 PC
8 PCS2 PCS6 PCS
NOTE: INSTALL THE GLASS ASSEMBLY
AFTER FIXTURE IS HUNG.
For Customer Service, contact the place of purchase to arrange for replacement parts.
CSA055303WALG2