Page 1
(G
)
INSTALLATION INSTRUCTIONS
Fixture Name: AUTUMN TWILIGHT 9903-M1L MSI
For Pendant Light Fixture
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
HANGING THE FIXTURE（Fig.1）
Fig.1
1. Carefully remove the new fixture from the carton and the
yellow bag that holds all parts. Check that all parts are
included as shown in the illustration and parts list.
2. Shut off the power at the circuit breaker and remove old
fixture from ceiling, including the old mounting strap.
JUNCTION BOX
(CEILING)
3. Thread Nipple(C) into Canopy Loop (F) until snug.
4. Thread other end of the Nipple (C) with Canopy Loop
attached into Mounting Strap (D).
5. Place Lock Washer (B) over end of Nipple (C) protruding
A
B
through Mounting Strap (D) and thread Hex Nuts (A) onto
Nipple until tight.
6. Take this mounting strap assembly and mount to ceiling
D
C
junction box with junction box Screws (E). Tighten screw
securely with screw driver.
E
7. Unscrew the Canopy loop collar (H) from the Canopy
loop. Take the canopy and pass over the Canopy loop.
F
Approximately one half of the canopy loop exterior
threads should be exposed. Adjust until desired height is
reached. You may need to cut short the wire and
I
reconnect with transformer refer original mode. *the
Canopy loop collar should fit snugly on the Canopy loop
after the canopy is installed. Remove Canopy and
Canopy loop collar.
G
8. Assemble the fixture and have an assistant or secure
support hold the weight of the fixture while you complete
the wiring connections.
H
9. Thread the fixture wires and ground wire of the
assembled fixture through the canopy loop (F) and
CHAIN
nipple(C) and chain (every three links) into th e outlet box.
CONNECTING THE WIRES (Fig.2)
10. Attach the power supply wires to the fixture lead wires
by connecting BLACK to BLACK (or SMOOTH) and WHITE
to WHITE (or RIBBED).
J
11. Attach the GROUND wire (GREEN or COPPER) from the
Junction Box and the fixture Ground wire to the green
Ground Screw on the Mounting Bracket (B) or connect
both wires together using the correct size of wire
connectors.
NOTE: Twist the wires together in the same direction you
Fig.2
HOUSE WIRES
twist the wire connector onto the wires.
12. Tuck these wire connections neatly into the Junction
Box.
FINISHING THE INSTALLATION (Fig.3)
13. Raise Canopy (G) to the ceiling and secure in place by
tightening the Canopy loop collar (H) into the Canopy
Loop (F).
14. Install the light bulb s and crystals as per the fixture
assembly sheet.
YOUR INSTALLATION IS NOW COMPLETE. TURN POWER ON AT
TO THE JUNCTION BOX & TEST THE FIXTURE.
For Customer Service, contact the place of purchase to arrange for replacement parts.
FIXTURE WIRES
SMOOTH
(or Black)
RIBBED
(or White )
BARE COPPER
(or Green)
(Neutral)
GREEN
round
CSA055304DALG2
I
BLACK
(Hot)
WHITE
Page 2
g
PARTS & ASSEMBLY SHEET
Fixture Name: AUTUMN TWILIGHT 9903-M1L MSI
This fixture assembled PO: Date:
Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or
damaged, please note on this sheet and contact the place of purchase to arrange for replacement parts .
Company Name:______________________Co Account#:__________
PARTS LIST
below to be filled out by retailer
Canopy
1ea Φ135*H55 ㎜
Chain
1ea Φ3.8*6ft
Link
2ea W20*H45 ㎜
Crystal Leaf
(PT-LEAF-9903 MSI)
9ea W27*H65 ㎜
Hex Nut
2ea NPS-1/4-18
Nipple
1ea NPS 1/4-18*75
Mounting Strap
1ea W103*T2.0 ㎜
Bulbs
4ea Halo
Type G4 10W
㎜
en,
Wire Connectors
3ea Orange
Canopy Loop
1ea NPS 1/4-18*H41
Mounting Screws
2ea G8/32*H32 ㎜
㎜
Part Needed ______________________________ Quantity _________________________________
Part Needed ______________________________ Quantity _________________________________
Reason why (missing, scratched, broken glass, bent, bad finish)
Comments __________________________________________________________________________
FIXTURE ASSEMBLY INSTRUCTIONS
Read and review installation instruction sheet
before assembling the fixture
1. Open bag on the arm and carefully arrange the
bead strings.
2. Screw Crystal Leaf (A) on the arm.
Hold carefully by the metal base to prevent the
crystal from cracking.
3. Install the light bu lbs in accordance with the
fixture's specification.
Bulb note: Use a tissue or paper towel to hold t he
bulb and push down into socket. Oils or dirt can
cause the bulb life to shorten. Rubbing alcohol is
recommended to clean the bulbs if dirty.
(DO NOT EXCEED THE MAXIMUM WATTAGE RATING!)
9903-M1L MSI
Fig.3
A
7 PCS4 PCS3 PCS4 PCS
For Customer Service, contact the place of purchase to arrange for replacement parts.
CSA055304DALG2
Page 3
Loading...