Golden Lighting 9903-BA3 User Manual
INSTALLATION INST RUCTIONS
Fixture Name: AUTUMN TWILIGHT 9903-BA3
For Wall Mount Light Fixture
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
HANGING THE FIXTURE (Fig.1)
1. Carefully remove the new fixture from the c ar ton
CONNECTING THE WIR E S（Fig.2）
6.
7. Attach the GROUND wire (GREEN or COPPER)
NOTE: Twist the wires together in the same direction
you twist the wire connector onto the wires.
8. Tuck these wire connections neatly into the
FINISHING THE INSTALLATION（Fig.3）
9. After tucking the wire connections
10. Install
YOUR INSTALLATION IS NOW COMPLETE. RETUR N
POWER TO THE JUNCTION BOX AND TEST THE FIXTURE.
Fig. 1
JUNCTION BOX
D B A
C
Fig.2
HOUSE WIRES
BLACK
(Hot)
FIXTURE WIRES
SMOOTH
(or Black)
RIBBED
(or White)
BARE COPPER
(or Green)
WHITE
(Neutral)
GREEN
(Ground)
Fig.3
E
JUNCTION BOX
C
D
F For Customer Service, contact the place of purchase to arrange for replacement parts.
C S A0 55 30 3V AL G 1
and the yello w par ts b a g. C heck t ha t al l p ar ts a r e
included as sho w n i n th e il lu s tr a tio ns an d P ar ts a n d
Assembly Sheet.
2. Shut off power at the circuit breaker and remove
the old fixture from wall, including the old
mounting strap.
3. Mounting Strap (A) contains several pairs of
threaded holes, Find the pair of holes that matches
the holes spacing in Back Plate (D) and thread the two
Mounting Screws (C) half way into Mounting Strap (A).
4. Place Mounting Strap (A) over the Junction
Box so that Mounting Screws (C) are vertical
or horizontal, as required by the fixture type.
5. Attach Mounting Strap (A) to the
Junction Box using the two Mounting Screws (B).
Tighten Mounting Screws (B) securely with a screwdriver.
Attach the power supply wires to the fixture lead
wires by connecting BLACK to BLACK (or SMOOTH)
and WHITE to WHITE (or RIBBED).
from the Junction Box and the fixture Ground wire
to the green Ground Screw on the Mounting
Bracket (B) or connect both wires together using
the correct size of wire connectors.
Junction Box.
into
the Junction Box, place Back Plate
(D) over the two Mounting Screws (C) and secure
Back Plate (D) against the wall by threading
two Deco Nuts (E) over Mounting Screws
(C) until tight (as shown on Fig.3).
the crystals as per the Parts and Assembly
Sheet instructions.
PARTS & ASSEMBLY SHEET
Fixture Name: AUTUMN TWILIGHT 9903-BA3
This fixture assembled PO:
Notice:
Date:
Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or
damaged, pl ease note on this sheet and contact the place of purchase to arrange for replacement pa rts.
PARTS LIST
Mounting Strap
Φ
1ea
Wire Connec tors
Orange 3ea
Crystal Leaf
PT-CRYSTAL-9903 LEAF
Company Name:_______________ ____ ___ Co Account#:__________
below to be filled out by retailer
Green Screw
G8/32*H8
1ea
Hex Nut
G5/32*H4
2ea
Bulbs
3ea Halogen,
Type G9 40W
Mounting Screws
H32 ㎜ 2ea H38
2ea
Deco Nut
2ea
20ea W27*H65
Part Needed ______________________________
Part Needed ___________________________ ___
Comments
Quantity _________________________________
Quantity _________________________________
Reason why (missing, scratched, broken glass, bent, bad finish)
__________________________________________________________________________
9903-BA3
Fig.1
FIXTURE ASS EM BLY INSTRUCT I ONS
Read and review installation instruction sheet
before assembling the fixture
1.Open the bag that is attached to the fixture and
2. Screw Crystal Leaf (A) on the arm.
E
D
C
B
3. Place the Glass (C) and Piece (D) over the Socket
4. Install
(DO NOT EXCEED THE MAXIMUM WATTAGE RATING!)
A
NOTE: INSTALL THE GLASS ASSEMBLY
AFTER FIXTURE IS HUNG.
For Customer Service, contact the place of purchase to arrange for replacement parts.
C S A0 55 30 3V AL G 1
102 ㎜
㎜
carefully arrange the bead strings.
Hold carefully by the metal base to prevent the
crystal from cracking.
㎜
㎜
㎜
Φ12 ㎜
(B) and secure with Socket Ring (E).
the light bulbs in accordance with the
fixture's specification.
Bulb note: Use a tissue or paper towel to hold the
bulb and push down into socket. Oils or dirt can
cause the bulb life to shorten. Rubbing alcohol is
recommended to clean the bulbs if dirty.
Loading...