Golden Lighting 9903-24 MSI User Manual
(G
)
INSTALLATION INSTRUCTIONS
Fixture Name: AUTUMN TWILIGHT 9903-24
For Chandelier Light Fixture
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
HANGING THE FIXTURE（Fig.1）
1. Carefully remove the new fixture from the carton and
Fig.1
JUNCTION BOX
(CEILING)
the yellow bag that holds all parts. Check that all parts
are included as shown in the illustration and parts list.
2. Shut off the power at the circuit breaker and remove
old fixture from ceiling, including the old mounting
strap.
3. The Mounting Strap (B) contains several pairs of
threaded holes, find the pair of holes that match the
holes spacing in your fixture Canopy (D) and thread
the Nipple (A) half way into the Fixture Mounting Strap
(B).
4. Attach the Fixture Mounting Strap (B) to the Junction
Box using the two Mounting Screws (C). Tighten the
Screws (C) securely with screwdriver.
5. Measure and adjust for the correct length of cable
needed for hanging height.
CONNECTING THE WIRES (Fig.2)
6. Attach the power supply wires to the fixture lead wires
by connecting BLACK to BLACK (or SMOOTH) and
WHITE to WHITE (or RIBBED).
7. Attach the GROUND wire ( GREEN or COPPER) from the
Junction Box and the fixture Ground wire to the green
Ground Screw on the Mounting Bracket (B) or connect
both wires together using the correct size of wire
connectors.
NOTE: Twist the wires together in the same direction you
twist the wire connector onto the wires.
8. Tuck these wire connections neatly into the Junction
Box.
FINISHING THE INSTALLATION (Fig.3)
9. Raise Canopy (D) to the ceiling and secure in place
by tightening the Deco Nut (F).
Fig.2
HOUSE WIRES
10. Install the light bulbs and crystals as per the fixture
assembly sheet.
YOUR INSTALLATION IS NOW COMPLETE. TURN POWER ON
AT TO THE JUNCTION BOX & TEST THE FIXTURE.
FIXTURE WIRES
SMOOTH
(or Black)
RIBBED
(or White)
(Neutral)
GREEN
round
BARE COPPER
(or Green)
For Customer Service, contact the place of purchase to arrange for replacement parts.
CSA055324HALG1
A
B
C
D
F
BLACK
(Hot)
WHITE
PARTS & ASSEMBLY SHEET
Fixture Name: AUTUMN TWILIGHT 9903-24
This fixture assembled PO: Date:
Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or
damaged, please note on this sheet and contact the place of purchase to arrange for replacement parts.
Company Name:______________________Co Account#:__________
PARTS LIST
below to be filled out by retailer
Canopy
1ea Φ175*H65 ㎜
Mounting Screws
2ea G8/32*H32 ㎜
Green Screw
1ea G8/32*H8 ㎜
Crystal Leaf
PT-CRYSTAL-9903 LEAF
144ea W27*H65 ㎜
Hex Nut
1ea NPS-1/4-18
Nipple
1ea NPS 1/4-18*90
Mounting Strap
1ea W103*T2.0 ㎜
Cable Lock
6ea W16*H8
㎜
㎜
Wire Connectors
3ea Orange
Deco Nut
1ea Φ19 ㎜
Bulbs
24ea Halogen,
Type G4 20W
Part Needed ______________________________ Quantity _________________________________
Part Needed ______________________________ Quantity _________________________________
Reason why (missing, scratched, broken glass, bent, bad finish)
Comments __________________________________________________________________________
FIXTURE ASSEMBLY INSTRUCTIONS
Read and review installation instruction sheet
before assembling the fixture
1. Open the bag that is attached to the arm and
carefully arrange the bead strands.
2. Screw Crystal Leaf (F) onto the arm. Hold the
crystal carefully by the metal base to prevent the
crystal from cracking.
3. Install the light bu lbs in accordance with the
fixture's specification.
Bulb note: Use a tissue or paper towel to hold the
bulb and push down into socket. Oils or dirt can
cause the bulb life to shorten. Rubbing alcohol is
recommended to clean the bulbs if dirty.
(DO NOT EXCEED THE MAXIMUM WATTAGE RATING!)
9903-24
Fig.3
F
B&D
each 6pcs
78pcs 126pcs 114pcs 126pcs 12pcs
A
B
C
D
E
For Customer Service, contact the place of purchase to arrange for replacement parts.
CSA055324HALG1
Loading...