Golden Lighting 9106-BA2 PW User Manual

2ea 5/32-IP*H3mm

2ea 5/32-IP*H9mm

Reason why ( missing, scratched, broken glass, bent, bad finish)

Comments

Read and review installation instruction sheet before
assembling the fixture.

NOTE: I

Company Name:_______________________Co. Account #:_____________

below to be filled out by retailer

PARTS & ASSEMBLY SHEET

Fixture Name: Taylor 9106-BA2 PW

This fixture assembled PO:__________ Date: ________

Notice: Please review the parts listing and check for all pa rts before assembling the fixture. If any parts are miss ing or

damaged, please note on this s heet a nd c ontac t the place of purchase to arrange for replacement parts.

PARTS LIST

Circular Mounting
Strap

1ea Φ4"*H1.2mm 2ea 8/32-IP*1" 2ea 5/32-IP*1"

Hex nut Wire connnector Deco nuts

Part Needed Quantity
Part Needed Quantity

Mounting screw Mounting screw

3ea A3 Orange

FIXTURE ASSEMBLY INSTRUCTIONS

9106-BA2 PW

Fig 1

1. Slide the Glass Shade (K) over Socket (G) and secure it by
threading the Socket Ring (I) onto the Threaded Socket (G)
until tight.

2. Install the light bulbs in accordance with the fixture's
specification.

(DO NOT EXCEED THE MAXIMUM WATTAGE RATING!)

NSTALL THE GLASS ASSEMBLY AFTER

THE FIXTURE IS HUNG.

For Customer Service, contact the place of purchase to arrange for replacement parts.

9106 PartsInstallation-121208.xls

G

I

K

Fig. 2

INSTALLATION INSTRUCTIONS

Fixture Name: Taylor 9106-BA2 PW

For Wall Mou nt Light Fixture

WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.

HANGING THE FIXTURE (Fig 1)

1. Carefully remove the new fixture from the carton and the
yellow bag that holes all your parts. Check that all parts are
included as shown in the illustration and parts list.

2. Shut off power at the circuit breaker and remove the old
fixture from wall, including the old mounting strap.

3. The Mounting Strap (B) contains several pairs of threaded
holes, find the pair of holes that match the holes spacing in
your fixture Back Plate (E) and thread the two Fixture Mounting
Screws (C) half way into the Fixture Mounting Strap (B).

4. Place the Mounting Strap (B) over the Junction Box so the
Fixture Mounting Screws(C) are vertical or horizontal, as
required by the fixture type.

5. Attach the Fixture Mounting Strap (B) to the Junction Box
using the two mounting screws (A). Tighten the screws (A)
securely with screwdriver.

CONNECTING THE WIRES (Fig 2)

6. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to
WHITE (or RIBBED).

7. Attach the GROUND wire(GREEN or COPPER) from the
Junction Box and the fixture Ground wire to the green Ground
Screw on the Mounting Bracket (B) or connect both wires
together using the correct size of wire connectors.
NOTE: Twist the wires together in the same direction you twist
the wire connector onto the wires.

8. Tuck these wire connections neatly into the Junction Box.

Fig. 1

FINISHING THE INSTALLATION (Fig 3)

9. Place the fixture Back Plate (E) over the two Mounting
Screws (C) and secure the Back Plate (E) against the wall by
threading two Deco nuts (F) over the two Mounting Screws (C)
until tight as shown on Fig.1

YOUR INSTALLATION IS NOW COMPLETE. RETURN
POWER TO THE JUNCTION BOX AND TEST THE FIXTURE.

Fig. 3

For Customer Service, contact the place of purchase to arrange for replacement parts.

E
F