Golden Lighting 8995-M1L SBZ User Manual
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
Rod
PARTS & ASSEMBLY SHEET
Company Name:_______________________Co. Account #:_____________
to be filled out by retailer
Fixture Name: Woodbriar 8995-M1L S BZ
This fixture assembled PO:__________ Date: ________
Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing
or damaged, please note onthis sheet and contact the place of purchase to arrange for replacement parts.
PARTS LIST
Canopy Mounting Screws
1ea ∅5"*H1" 2ea 8#32-IP*1"
Wire connectors Mounting Screws Hex Nut
3ea P3 Orange 2ea 5/32-IP*1-1/2" 2ea 5/32-IP*H3mm
Rod
3ea ∅12.5*H12" 1ea ∅12.5*H6" 2ea 5/32-IP*H9mm
Part Needed Quantity
Mounting Strap
1ea ∅4"*H2mm
Deco Nut
FIXTURE ASSEMBLY INSTRUCTIONS
Read and review installation instruction sheet before
assembling the fixture.
Fig 1
1. By measuring determine correct number of rods needed
for proper hanging height. There are 3 optional 12" rods
and 1 6" rod included. To shorten the fixture slide the extra
rods off the wire. To lengthen the fixture thread the
additional rods onto the wire.
8995-M1L SBZ
2. Pull the fixture's wire through the Rods (G).
3. Thread Rod/rods (G) into Fixture frame (H) turning until
tight, repeat for the additional rods. Thread the Swivel
assembly (F) to the Rod (G).
NOTE: INSTALL THE GLASS ASSEMBLY AFTER
THE FIXTURE IS HUNG.
4. Place the Glass Shade (J) over the Threaded Socket (I)
and secure by threading the Socket Ring (K) to Threaded
Socket (I) until tight.
5. Install the light bulb in accordance with the fixture's
specifications.
(DO NOT EXCEED MAXIMUM WATTAGE RATING)
For Customer Service, contact the place of purchase to arrange for replacement parts.
8995Series instructions_20120522m.xls
These two Rods may
be removed
or
additional Rods may
be added.
ROD-12 DNI *
*available for purchase
separately
(E) securely with screw driver.
INSTALLATION INSTRUCTIONS
fixture assembly sheet.
Fixture Name: Woodbriar 8995-M1L SBZ
For Mini Penda nt Light Fixture
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE (Fig. 1)
1. Carefully remove the new fixture from t he car ton and
the yellow bag that holds all your parts. Check that all
parts are included as shown in the illustration and parts
list.
2. Shut off power at the circuit br eaker and remove the
old fixture from ceiling, including the old mounting strap.
3. The Mounting bracket ( C ) cont ains several pairs of
threaded holes, find the pair of holes that match the
hole spacing in your fixture Back Plate (N) and thread
the two Mounting Screws (B) half way into the Mounting
Strap (C) facing down, these will have their threaded
ends protrude through the two holes in the f ixtur e
canopy(N).
4. Place the Mounting Strap ( C ) over the junction box
5. Attach the Mounting Strap (C) to t he Junction Box
using the two mounting screws (E). Tig hten the screws
CONNECTING THE WIRES (Fig. 2)
6. Attach the power supply wires to the fixture lead
wires by connecting BLACK to BLACK (or SMOOTH)
and WHI TE to WHITE (or RIBBED).
7. Attach the GROUND wire(GREEN or COPPE R)
from the Junction Box and the fixture G round wire to the
green Ground Screw on the Mounting Bracket (E) or
connect both wires together using the cor r ec t s ize of
wire connectors.
NOTE: Twist the wires together in the sam e dir ect ion
you twist the wire connector onto the wires.
8. Tuck these wire connections neatly into the Junction
Box.
Fig. 1
Fig. 2
FINISHING THE INSALLATION (Fig. 3)
9. Place the fixture’s canopy over the Mounting bracket
(C), adjust the canopy (N) until the Mounting Screws (B)
protrude out from t he canopy (N) and s ecur e by
threading the Decorative nuts (O) on unt il tight.
10. Install the light bulbs and glass shade as per t he
YOUR INSTALLATIO N I S NOW CO MPLETE.
RETURN POWER TO THE JUNCTION BOX AND
TEST THE FIXTURE.
For Customer Service, contact the place of purchase to arrange for replacement parts.
Fig. 3
Loading...