Golden Lighting 8981-BA4 BRI User Manual
Crystal drops
Reason why
( missing, scratched, broken glass, bent, bad finish)
Comments
PARTS & ASSEMBLY SHEET
Company Name:_______________________Co. Account #:_____________
below to be filled out by retailer
NOTE: I
Glass Shade (G) and into the Backplate (E) until tight.
I
F
Fixture Name: Echelon 8981-BA4 BRI / GRM
This fixture assembled PO:__________ Date: ________
Notice:
damaged, please note onthis sheet and contact the place of purchase to arrange for replacement parts.
Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or
PARTS LIST
Mounting Strap Deco nut
1ea 102*H1.2mm 2ea 10*H9mm 8/32"*H1" 2ea5/32"*H1" 2ea
Hex nut Wire connectors Green screw
2ea 5/32"*H3mm 2ea A3 Orange 1ea 8/32"*H10mm
Crystal drops
B1 x 12 pcs
Part Needed Quantity
Part Needed Quantity
C2 x 4pcs
Mounting Screw
Crystal drops are included in
parts bag. (see crystal assembly
instruction)
F
IXTURE ASSEMBLY INSTRUCTIONS
Read and review installation instruction sheet before
assembling the fixture.
1. Secure Glass Shade (G) to the fixture Backplate (E)
by threading the Deco Screw (H & I) through holes in
2. Install the light bulb in accordance with the fixture's
specifications.
(DO NOT EXCEED MAXIMUM WATTAGE RATING!)
NSTALL THE GLASS ASSEMBLY AFTER
THE FIXTURE IS HUNG.
8981-BA4 BRI/GRM
Fig.1
For Customer Service, contact the place of purchase to arrange for replacement parts.
INSTALLATION INSTRUCTIONS
included as shown in the illustration and parts list.
fixture from wall, including the old mounting strap.
required by the fixture type.
CONNECTING THE WIRES (Fig 2)
WHITE (or RIBBED).
together using the correct size of wire connectors.
E
Fixture Name:
Echelon 8981-BA4 BRI / GRM
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE (Fig.1)
1.Carefully remove the new fixture from the carton and the
yellow bag that holes all your parts. Check that all parts are
2. Shut off power at the circuit breaker and remove the old
3. The Mounting Strap (B) contains several pairs of threaded
holes, find the pair of holes that match the holes spacing in
your fixture Back Plate (E) and thread the two Fixture
Mounting Screws (C) half way into the Fixture Mounting Strap
(B).
4. Place the Mounting Strap (B) over the Junction Box so the
Fixture Mounting Screws(C) are vertical or horizontal, as
5. Attach the Fixture Mounting Strap (B) to the Junction Box
using the two mounting screws (A). Tighten the screws (A)
securely with screwdriver.
For Wall Mount Light Fixture
Fig. 1
6. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to
7. Attach the GROUND wire(GREEN or COPPER) from the
Junction Box and the fixture Ground wire to the green Ground
Screw on the Mounting Bracket (B) or connect both wires
NOTE: Twist the wires together in the same direction you twist
the wire connector onto the wires.
8. Tuck these wire connections neatly into the Junction Box.
FINISHING THE INSTALLATION (Fig.3)
9. Place the fixture Back Plate (E) over the two Mounting
Screws (C) and secure the Back Plate (E) against the wall by
threading two Deco nuts (F) over the two Mounting Screws (C)
until tight as shown on Fig.1
10. Install glass as per the fixture assembly instructions.
YOUR INSTALLATION IS NOW COMPLETE. RETURN
POWER TO THE JUNCTION BOX AND TEST THE
FIXTURE.
Fig. 2
Fig. 3
For Customer Service, contact the place of purchase to arrange for replacement parts.
Loading...