Golden Lighting 8981-BA2 BRI User Manual

Wire

connectors

Crystal drops

Reason why

( missing, scratched, broken glass, bent, bad finish)

Comments

PARTS & ASSEMBLY SHEET

Notice:

Please review the parts listing and check for all parts before assembling the fixture. If any parts are

Company Name:_______________________Co. Account #:_____________

below to be filled out by retailer

NOTE: I

1. Secure Glass Shade (G) to the fixture Backplate

(E) until tight.

G

F

H

I

E

Fixture Name: Echelon 8981-BA2 BRI / GRM

This fixture assembled PO:__________ Date: ________

missing or damaged, please note onthis sheet and contact the place of purchase to arrange for replacement parts.

PARTS LIST

Mounting Strap Deco screw

1ea 102*H1.2mm 2ea 10*H9mm 8/32"*H1" 2ea5/32"*H1" 2ea

Hex nut

2ea 5/32"*H3mm 2ea A3 Orange 1ea 8/32"*H10mm

B1 x 6pcs

Part Needed Quantity

F

IXTURE ASSEMBLY INSTRUCTIONS

Read and review installation instruction sheet before assembling the fixture.

C2 x 2pcs

Fig 1

Mounting Screw

Green screw

Crystal drops are included in

parts bag. (see crystal assembly

instruction)

8981-BA2 BRI/GRM

(E) by threading the Deco Screw (H & I) through holes in Glass Shade (G) and into the Backplate

2. Install the light bulb in accordance with the fixture's specifications.

(DO NOT EXCEED MAXIMUM WATTAGE RATING!)

NSTALL THE GLASS ASSEMBLY

AFTER THE FIXTURE IS HUNG.

For Customer Service, contact the place of purchase to arrange for replacement parts.

INSTALLATION INSTRUCTIONS

included as shown in the illustration and parts list.

fixture from wall, including the old mounting strap.

required by the fixture type.

CONNECTING THE WIRES (Fig 2)

WHITE (or RIBBED).

together using the correct size of wire connectors.

H

I

F

Fixture Name:

Echelon 8981-BA2 BRI / GRM

WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.

HANGING THE FIXTURE (Fig.1)

1.Carefully remove the new fixture from the carton and the

yellow bag that holes all your parts. Check that all parts are

2. Shut off power at the circuit breaker and remove the old

3. The Mounting Strap (B) contains several pairs of threaded

holes, find the pair of holes that match the holes spacing in

your fixture Back Plate (E) and thread the two Fixture

Mounting Screws (C) half way into the Fixture Mounting Strap

(B).

4. Place the Mounting Strap (B) over the Junction Box so the

Fixture Mounting Screws(C) are vertical or horizontal, as

5. Attach the Fixture Mounting Strap (B) to the Junction Box

using the two mounting screws (A). Tighten the screws (A)

securely with screwdriver.

For Wall Mount Light Fixture

Fig. 1

6. Attach the power supply wires to the fixture lead wires by

connecting BLACK to BLACK (or SMOOTH) and WHITE to

7. Attach the GROUND wire(GREEN or COPPER) from the

Junction Box and the fixture Ground wire to the green Ground

Screw on the Mounting Bracket (B) or connect both wires

NOTE: Twist the wires together in the same direction you twist

the wire connector onto the wires. 8.

Tuck these wire connections neatly into the Junction Box.

FINISHING THE INSTALLATION (Fig.3)

9. Place the fixture Back Plate (E) over the two Mounting Screws (C) and secure the Back Plate (E) against the wall by threading two Deco nuts (F) over the two Mounting Screws (C) until tight as shown on Fig.1

10. Install glass as per the fixture assembly instructions.

Fig. 2

Fig. 3

G

E

YOUR INSTALLATION IS NOW COMPLETE. RETURN POWER TO THE JUNCTION BOX AND TEST THE FIXTURE.

For Customer Service, contact the place of purchase to arrange for replacement parts.