Golden Lighting 8981-5 GRM User Manual
Canopy Loop
loop collar
Crystal drops
Crystal drops
Crystal drops
Part Needed
Quantity
Reason why
( missing, scratched, broken glass, bent, bad finish)
Comments
PARTS & ASSEMBLY SHEET
Company Name:_______________________Co. Account #:_____________
Fixture Name: Echelon 8981-5 BRI / GRM
This fixture assembled PO:__________ Date: ________
Notice:
missing or damaged, please note on this sheet and contact the place of purchase to arrange for
replacement parts.
PARTS LIST
Canopy
1ea 130*H22mm 1ea 1/2"*H3mm 2ea 1/2"*H55mm
Chain Wire Connnector
1ea 3.8mm*L72" 2ea A3 Orange
Chain connector Mounting Screw Finial
2ea 5*H58.5mm 2ea 8/32"*H1" 1ea 22*H40mm
Mounting Strap
w/ ground screw
1ea 100*22*H4mm
/1ea 8/32"*H10mm
Crystal draping
A7 x 5pcs
Please review the parts listing and check for all parts before assembling the fixture. If any parts are
to be filled out by retailer
Hex nut Nipple
Bottom cap
1ea 50*H56mm
Crystal drops are included in
parts bag. (see crystal assembly
instruction)
D4 x 1pcs
Crystal drops
B2 x 15pcs
and Canopy
1ea 1/2"*H46mm
B5 x 5pcs
C3 x 5pcs
Part Needed Quantity
F
IXTURE ASSEMBLY INSTRUCTIONS
Read and review installation instruction sheet before
assembling the fixture.
1. Feed the fixture wires through the long Threaded rod (F)
and pull the wires until taut.
2. Slide the tube (E), tube lid (D), cup (C), long Threaded rod
(F), Top cap (B), Top loop (A) down to housing of fixture.
3. Screw Threaded rod (F) all the way into the coupler (L) at
housing of fixture. Screw Top loop (A) into Top cap (B).
NOTE: THE SHADE ASSEMBLY CAN BE DAMAGED BY
ROUGH HANDLING. USE CARE WHEN ASSEMBLING.
Fig 1
Fig 1
8981-5 BRI / GRM
For Customer Service, contact the place of purchase to arrange for replacement parts.
the chain-not the electrical wire.
PARTS & ASSEMBLY SHEET
Fixture Name: Echelon 8981-5 BRI / GRM
5. Attach 3 crystal draping chain (G) to hook (H) of shade.
* NOTE: The Finial can be scratched or broken if the full
weight of the fixture is placed on it. To avoid damage attach
the Bottom Assembly parts after hanging the fixture.
4. Slide the center support of the Fabric shade(I) over center
tube to the housing, it is open on one side for ease of
assembly. Secure in place by tightening Cap nut (J) to
Frame (K) with frame of shade between them (I).
6. By measuring determine correct number of links needed
for proper hanging height. Use a pair of pliers to open one
link of the Chain (A2) then remove the excess Chain (A2)
and discard it.
7. Use one chain connector(A12) to attach one end of the
chain to the Top loop (A) and close the chain connector.
8. Feed the fixture wires through the Chain (every three
Fig 2
Fig 3
links) and pull the wires until taut.
9. Slip Canopy loop collar (A11) over the chain, then do the
same with the canopy .
10. When ready to complete the installation Use the other
chain connector and attach the other end of the chain to the
canopy loop (A10) and close the chain connector.
11. Make sure the weight of the chandelier is supported by
* You may now install the fixture.
Note: Complete these remaining steps after the fixture is
hung.
12. Secure threaded nipple (P) to bushing (M) of housing
and screw Hex nut (N) on to secure.
13. Place Bottom cap (O) over the Threade nipple (P).
14. Screw Finial (Q) to threaded nipple (P).
Fig 4
15. Install the light bulbs in accordance with the fixture's
specifications.
(DO NOT EXCEED MAXIMUM WATTAGERATING)
For Customer Service, contact the place of purchase to arrange for replacement parts.
Loading...