Golden Lighting 8201-SF SLV User Manual

Crystal draping

Crystal drops

Read and review installation instruction sheet before
assembling the fixture.

1. Measure to determine the correct number of links

chain to the Top loop (A). Close the chain. Feed the fixture

the chain, not the electrical wire.
* You may now install the fixture.

Fig 1

Company Name:_______________________Co. Account #:_____________

to be filled out by retailer

F

PARTS & ASSEMBLY SHEET

This fixture assembled PO:__________ Date: ________

Notice:

Fixture Name: Tetiva 8201-SF BLK/SLV

Please review the parts listing and check for all parts before assembling the fixture. If any parts
are missing or damaged, please note on this sheet and contact the place of purchase to arrange for
replacement parts.

PARTS LIST

Canopy

Chain

Chain
connector

Ax9pcs

Part Needed Quantity
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments

1ea Hex nut 2ea Nipple 2ea

1ea
6ft

2ea Mounting Screw

Box 6pcs

Wire Connector 2ea

Crystal drops are included in parts

bag. (see crystal assembly

instruction)

2ea
8/32-IP*1"

Mounting Strap
w/ ground
screw

Canopy Loop
and Canopy
loop collar

Mounting Screw

IXTURE ASSEMBLY INSTRUCTIONS

8201-SF BLK/SLV

1ea

1ea

2ea
5/32-IP*1-1/2"

needed for proper hanging height. Use a pair of pliers to
open one link of the Chain (A2) then remove the excess
Chain (A2) and discard it.

2. Use one chain connector (A12) to attach one end of the

wires through the Chain (every three links) and pull the
wires until taut.

4. Slip Canopy Loop Collar (A11) over the chain, then do
the same with the canopy .

5. To finish the installation, use the other chain connector
to attach the other end of the chain to the Canopy Loop
(A10) and close the chain connector.

6. Make sure the weight of the chandelier is supported by

For Customer Service, contact t he place of purchase to arrange for replacement parts.

Note: Complete these remaining steps after the fixture is

hung.

specifications.

Fig 2

Fig 3

7. Hang up the crystal A and B

8. Install the light bulbs in accordance with the fixture's

(DO NOT EXCEED MAXIMUM WATTAGE RATING)

Attention:
Figure 3 demonstrates how Part C can be used to
remove the Lamp Shade.

HANGING THE FIXTURE as Semi flush (Fig. 1)

2. Shut off power at the circuit breaker and completely remove

Fig. 1

CONNECTING THE WIRES (Fig. 2)

Fig. 2

INSTALLATION INSTRUCTION

Fixture Name: Tetiva 8201-SF BLK/SLV

For Semi Flush / Convertible Light Fi xtu

BARE COPPER

(Ground)

GR
(G

FIXTURE WIRES

SMOOTH (BLACK)

RIBBED (WHITE)

BLACK

WHITE

HOUSE WI

WARNING! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.

1. Carefully remove the new fixture from the carton and the
yellow bag that holds all your parts. Check that all parts are
included as shown in the illustration and Parts List.

the old fixture from ceiling, including the old mounting strap.

3.Circular Strap (B) contains several pairs of threaded holes.
Find the pair of holes that matches the spacing of the holes in
Canopy (F) and thread Mounting Screws (A) half way into the
Mounting Strap (B) facing down. Secure in place with hex nuts.
The threaded ends should protrude through the holes in
Canopy (F).

4. Place Mounting Strap (B) over the junction box.

5. Attach the Mounting Strap (B) to the Junction Box using
Mounting Screws (C). Tighten the screws securely with a screw
driver.

6. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to WHITE (
or RIBBED) .

7. Ground wire connection: Connect the fixture ground wire to
house ground wire, which usually has green or copper
insulation, with the correct size of wire connector. If there is no
house ground wire at ceiling junction box then attach fixture
ground wire securely onto green grounding screw located on
the mounting bar.
NOTE: Twist the wires together in the same direction that you
twisted the wire connector onto the wires.

8. Tuck the wire connections neatly into the Junction Box.