Page 1
Crystal draping
Crystal drops
Read and review installation instruction sheet before
assembling the fixture.
1. Measure to determine the cor r ec t number of chain links
the chain, not the electrical wire.
* You may now install the fixture.
Fig 1
Company Name:_______________________Co. Account #:_____________
F
PARTS & ASSEMBLY SHEET
Notice:
Fixture Name: Tetiva 8201-5P BLK/SLV
This fixture assembled PO:__________ Date: ________
Please review the parts listing and check fo r a ll parts before assembli ng the fixture. If any parts are
missing or damaged, please note on this sheet and contact the place of purchase to arrange for
replacement parts.
PARTS LIST
Canopy
Chain
Chain
Connector
Ax20pcs
Part Needed Quantity
Part Needed Quantity
Reason why (missing, scratched, broken glass, bent, bad finish)
Comments
1ea Hex nut 2ea Nipple 2ea
1ea
6ft
2ea Mounting Screw 2ea
Bx 6pcs
to be filled out by retailer
Wire Connector 2ea
Crystal drops are included in parts
bag. (see crystal assembly
instruction)
Mounting Strap
w/ ground
screw
Canopy Loop
and Canopy
Loop Collar
IXTURE ASSEMBLY INSTRUCTIONS
8201-5P BLK/SLV
1ea
1ea
needed for proper hanging height. Use a pair of plier s to
open one link of the Chain (A2). Then remove and discard
the excess Chain (A2).
2. Use one Chain Connector (A12) to attach one end of
the chain to the Top Loop (A) and close the chain. Feed
the fixture wires t hr ough the Chain (every three links) and
pull the wires until taut.
4. Slip Canopy Loop Collar (A11) over the chain. Then do
the same with the canopy .
5. To complete the installation, use the other chain
connector to attach the ot her end of the chain to the
Canopy Loop (A10) Close the chain connector.
6. Make sure the weight of the chandelier is supported by
Page 2
For Customer Service, contact the place of purchase to arrange for replacem ent par ts.
Note: Complete these remaining st eps after the fixture is
hung.
specifications.
Fig 2
Fig 3
7. Hang Crystals A and B
8. Install the light bulbs in accordance with the fixture's
(DO NOT EXCEED MAXIMUM WATTAGE RATING)
Attention:
Figure 3 demonstrates how Part C can be used to
remove the Lamp Shade.
Page 3
HANGING THE FIXTURE (Fig.1)
6. Take this mounting strap assembly and mount to ceiling junction
a screw driver.
Fig. 1
should fit snugly on the canopy loop after the canopy is installed.
through the canopy loop and nipple and into the outlet box.
CONNECTING THE WIRES (Fig. 2)
Fig. 2
INSTALLATION INSTRUCTIONS
13. Raise Canopy (G) to the ceiling and secure in place by
assembly sheet.
Fixture Name: Tetiva 8201-5/5P/SF/ BLK/SLV
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
1. Carefully remove the new fixture from the carton and the
yellow bag that holds all parts. Check that all parts are included
as shown in the illustration and the Parts and Assembly Sheet.
2. Shut off the power at the circuit breaker and completely
remove the old fixtur e from ceiling, including th e old mounting
strap.
3. Thread Nipple (C) into Ca nopy Loop (F) until snug.
4. Thread the other end of the Nipple (C) with the canopy loop
attached into Mou nting Strap (D).
5. Place Lock Washer (B) over end of Nipple (C) which should
protrude through Mounting Strap (D). Then thread Hex Nuts (A)
onto Nipple (C) until tight.
box with junction box Screws (E). Tighten the screws securely with
7. Unscrew the Canopy Loop Collar (H ) from the canopy loop.
Take the canopy and pass over the canopy loop. Approximately
one half of the canopy loop exterior threads should be exposed.
Adjust until desired height is reached. *The Canopy loop collar
For Chandeli er Light Fixture
Remove Canopy and Ca nopy lock collar.
8. Assemble the fixture and have an assistant or a secure support
to hold the weight of the fixture while you complete the wiring
connections.
9.Thread the fixture wires and ground wire of the assembled fixture
10. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to WHITE ( or
RIBBED) .
11. Ground wire con nection: Connect the fixture ground wire to
house ground wire, which usually has green or copper insulation,
with the correct size of wire connector. If there is no house ground
wire at ceiling junction box then attach fixture groun d wire
securely onto green grounding screw located on th e mounting
bar.
NOTE: Twist the wires together in the same direction that you
twisted the wire connector onto the wires .
12. Tuck the wire connections neatly into the Junction Box.
tightening the Canopy loop collar (H) into the Canopy Loop ( F)
14. Install the light bulbs a n d glass shade as per the fixture
For Customer Service, contact the place of purchase to arrange fo r replacement parts.
YOUR INSTALLATION IS NOW CO M PLETE.
RETURN POWER TO THE JUNCTION BOX AND
TEST THE FIXTURE.
Loading...