Golden Lighting 8201-1W BLKSLV User Manual

Circular Mounting
Strap

Mounting
Screw

2ea 5/32-IP*1-1/2"

2ea 5/32-IP*H3mm

Reason why ( missing, scratched, broken glass, bent, bad finish)

Comments

Read and review installation instruction sheet before
assembling the fixture.

PARTS & ASSEMBLY SHEET

This fixture assembled PO:__________ Date: ________

specification.

3. Hang the crystals

NOTE: INSTALL THE GLASS ASSEMBLY AFTER

PARTS LIST

Fig 1

Crystal Draping Ax4pcs

Company Name:_______________________Co. Account #:_____________

below to be filled out by retailer

Fixture Name: Tetiva 8201-1W BLK/SLV

Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or

damaged, please note on this sheet and contact the place of purchase to arrange for replacement parts.

Mounting Screw

1ea Φ4"*H1.2mm 2ea 8/32-IP*1"

Hex Nut Wire Connector Deco Nuts

3ea A3 Orange 2ea 5/32-IP*H9mm

Part Needed Quantity
Part Needed Quantity

IXTURE ASSEMBLY INSTRUCTIONS

F

8201-1W PW

1. Slide the Metal Candle Sleeve (L) over Socket (M) and
put the Shade (N) on the sleeve.
*Shade will be secured by the light bulb.

2. Install the light bulb in accordance with the fixture's

(DO
NOT EXCEED THE MAXIMUM WATTAGE RATING!)

THE FIXTURE IS HUNG.

For Customer Service, contact t he place of purchase to arrange for replacement parts.

INSTALLATION INSTRUCTIONS

FINISHING THE INSTALLATION (Fig 3)

TEST THE FIXTURE.

Fig. 3

HANGING THE FIXTURE (Fig 1)

securely with screwdriver.

Fig. 1

CONNECTING THE WIRES (Fig 2)

Box.

Fig. 2

Fixture Name: Tetiva 8201-1W BLK/SLV

WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.

1. Carefully remove the new fixture from the carton and
the yellow bag that holds all your parts. Check that all
parts are included as shown in the illustration and Parts
List.

2. Shut off power at the circuit breaker and completely
remove the old fixture from wall, including the old
mounting strap.

3. Mounting Strap (B) contains several pairs of
threaded holes. Find the pair of holes that matches the
holes spacing in your fixture Back Plate (E) and thread
Fixture Mounting Screws (C) half way into the Fixture
Mounting Strap (B).

4. Place the Mounting Strap (B) over the Junction Box
so that Fixture Mounting Screws (C) are vertical or
horizontal, as required by the fixture type.

5. Attach the Fixture Mounting Strap (B) to the Junction
Box using Mounting Screws (A). Tighten the screws

For Wall Mount Light Fixture

6. Attach the power supply wires to the fixture lead
wires by connecting BLACK to BLACK (or SMOOTH)
and WHITE to WHITE (or RIBBED).

7. Attach the ground wire (GREEN or COPPER) from
the Junction Box and the fixture ground wire to the
green Ground Screw on the Mounting Bracket (B) or
connect both wires together using the correct size of
wire connectors.
NOTE: Twist the wires together in the same direction
that you twisted the wire connector onto the wires.

8. Tuck these wire connections neatly into the Junction

9. Place the Back Plate (E) over the two Mounting
Screws (C). Secure the Back Plate (E) against the wall
by threading Deco nuts (F) over the Mounting Screws
(C) until tight as shown on Fig.1

YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCT ION BOX AND

For Customer Service, Contact the Place of Purchase to a rrange for Replacement Parts.