Company Name:_______________________Co. Account #:_____________
Canopy loop
Fixture Name: Alston Place 8118-SF BUS
This fixture assembled PO:__________ Date: ________
Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or
damaged, please note on this sheet and contact the place of purchase to arrange for replacement parts.
PARTS LIST
Canopy Mounting Screws Top Loop
1ea ∅5-3/4"*H1-1/2"4ea 8#32-IP*1"1ea 1/8-IP*H60mm
ChainWire connectorsMounting Strap
1ea 6ft ∅3.8 3ea P3 Orange 1ea W4-1/8"*E1"*H5mm
Chain Connector
2ea ∅5.8*H61mm 1ea ∅1-1/8"*H42mm1ea 1/4-IP*H60mm
CapNipple
1ea ∅1-1/2"*H5mm1ea 1/8-IP*H35mm1ea 1/8-IP"*H15mm
FinialNippleDeco Nut
1ea ∅1-1/4"*H49mm1ea 1/8-IP*H85mm
Mounting Strap Hex Nut Mounting Screws
1ea ∅4"*H2mm2ea 5/32-IP*H3mm 2ea 5/32-IP*2-1/2"
Part NeededQuantity
Part NeededQuantity
Reason why(missing, scratched, broken glass, bent, bad finish)
Comments
to be filled out b y retailer
with Collar
Nipple
Connector
2ea 5/32-IP*H10mm
FIXTURE ASSEMBLY INSTRUCTIONS
Read and review installation instruction sheet
before assembling the fixture.
ASSEMBLING THE FIXTURE as Semi-flush (Fig. 1)
1. Thread Nipple (T) into Connector (R). Slide Glass
Shade (S), then Cap (U) onto Nipple (T). Thread
connector (V) until tight.
2. Thread Nipple (W) into connector (V). Put Cap (X)
onto Nipple (W) and use Finial (Y) to tighten.
3. Install the light bulbs in accordance with the fixture's
specification.
DO NOT EXCEED MAXIMUM WATTAGE RATING!
NOTE: INSTALL THE GLASS ASSEMBLY
AFTER THE FIXTURE IS HUNG.
For Customer Service, contact the place of purchase to arrange for replacement parts.
Fig. 1
8118-SF BUS
Page 2
PARTS & ASSEMBLY SHEET
Fixture Name: Alston Place 8118-SF BUS
ASSEMBLING THE FIXTURE as Chain hung
(Fig. 2)
1. Remove the circular strap from top of fixture.
Replace the long mounting screws with two short
screws to hold the Deco Nuts (E) in place on the
fixture Top Cap (D).
2. Feed the fixture wires through the Top Loop (F)
and pull the wires until taut. Then screw the Top
Loop (F) to the coupling on the top of fixture until
tight.
3. By measuring, determine correct number of links
needed for proper hanging height. Use a pair of
pliers to open one link of the Chain (C2) then
remove the excess Chain (C2) and discard it.
4. Use a chain connector (E2) to attach one end of
the chain to the Top loop (F) and close the chain
connector.
5. Feed the fixture wires through the chain (every
three links) and pull the wires until taut.
6. Slip Canopy Loop Collar (B2) over the chain,
then do the same with the canopy (F2).
7. When ready to complete the installation Use the
other chain connector and attach the other end of
the chain to the canopy loop (A2) and close the
chain connector.
8. Make sure the weight of the chandelier is
supported by the chain - not the electrical wire.
* You may now hang the fixture
Fig. 2
F2
A2
B2
E2
C2
F
D
E
NOTE: INSTALL THE GLASS ASSEMBLY AFTER
THE FIXTURE IS HUNG.
Complete the steps 1~3 as in Fig. 1 (ASSEMBLING
THE FIXTURE as Semi-flush)
For Customer Service, contact the place of purchase to arrange for replacement parts.
Page 3
INSTALLATION INSTRUCTIONS
halfway into the Mounting Strap. Secure in place with hex nuts.
Fixture Name: Alston Place 8118-SF BUS
For Semi Flush / Convertible Light Fixture
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE as Semi flush (Fig. 1)
1. Carefully remove the new fixture from the carton and the
yellow bag that holds all your parts. Check that all parts are
included as shown in the illustration and parts list.
2. Shut off power at the circuit breaker and remove the old
fixture from ceiling, including the old mounting strap.
3. The Circular Strap (A) contains several pairs of threaded
holes, find the pair of holes that match the hole spacing in your
fixture Back Plate (D) and thread the two Mounting Screws (C)
The screws will have their threaded ends protrude through the
two holes in the fixture canopy (D).
4. Place the Mounting Strap (A) over the junction box.
5. Attach the Mounting Strap (A) to the junction box using the
two Mounting Screws (B). Tighten the screws (B) securely with
a screwdriver.
CONNECTING THE WIRES (Fig. 2)
6. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to
WHITE (or RIBBED).
NOTE: Twist the wires together in the same direction you twist
the wire connector onto the wires.
7. Attach the GROUND wire (GREEN or COPPER) from the
junction box and the fixture ground wire to the green ground
screw on the Mounting Bracket (B) or connect both wires
together using a wire connector.
8. Tuck these wire connections neatly into the junction box.
Fig. 1
Fig. 2
FINISHING THE INSALLATION (Fig. 3)
9. Place the fixture’s canopy over the Mounting Strap (A) and
over the Mounting Screws (C). Adjust the fixture Canopy (D)
until the Mounting Screws (C) protrude out from the canopy
(D). Secure the fixture against the ceiling by threading the
decorative nuts (E) until tight.
10. Install the light bulbs and glass shade as per the fixture
assembly sheet.
YOUR INSTALLATION IS NOW COMPLETE. RETURN
POWER TO THE JUNCTION BOX AND TEST THE FIXTURE.
For Customer Service, contact the place of purchase to arrange for replacement parts.
the fixture while you complete the wiring connections.
Fig. 1
wire connector onto the wires.
Fixture Name: Alston Place 8118-SF BUS
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE as Chain Hung (Fig. 1)
1. Carefully remove the new fixture from the carton and the yellow
bag that holds all parts. Check that all parts are included as shown in
the illustration and parts list.
2. Shut off the power at the circuit breaker and remove old fixture
from ceiling, including the old mounting strap.
3. Thread Nipple (C) into Canopy Loop (F) until snug.
4. Thread other end of the Nipple (C) with Canopy Loop attached
into Mounting Strap (D).
5. Place Lock Washer (B) over end of Nipple (C) protruding through
6. Take this mounting strap assembly and mount to ceiling junction
box with junction box Screws (E). Tighten screws securely with
screwdriver.
7. Unscrew the Canopy Loop Collar (H) from the Canopy Loop (F).
Take the canopy and pass over the canopy loop. Approximatly half
of the canopy loop exterior threads should be exposed. Adjust until
desired height is reached. *The Canopy loop collar should fit snugly
on the Canopy loop after the canopy is installed. Remove Canopy
and Canopy lock collar.
8. Assemble the fixture and have an assistant support the weight of
For Semi Flush / Convertible Light Fixt u r e
9. Thread the fixture wires and ground wire of the assembled fixture
through the canopy loop and nipple, and into the outlet box.
CONNECTING THE WIRES (Fig. 2)
10. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to WHITE
(or RIBBED).
NOTE: Twist the wires together in the same direction you twist the
Fig. 2
11. Attach the GROUND wire (GREEN or COPPER) from the
junction box and the fixture ground wire to the green ground screw on
the Mounting Bracket (D). Or, connect both wires together using a
wire connector.
12. Tuck these wire connections neatly into the junction box.
FINISHING THE INSTALLATION
13. Raise the Canopy (G) to the ceiling. Secure in place by
tightening the Canopy Loop Collar (H) onto the Canopy Loop (F).
14. Install the light bulbs and glass shade according to the fixture
assembly sheet.
For Customer Service, contact the place of purchase to arrange for replacement parts.
YOUR INSTALLATIO N I S NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX AND
TEST THE FIXTURE.
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.