Page 1
PARTS & ASSEMBLY SHEET
NOTE: I
Fixture Name: Alston Place 8118-M3 PW
This fixture assembled PO:__________ Date: ________
Notice: Please review the parts listing and check for all pa rts before assembling the fixture. If any parts are miss ing or
damaged, please note on this s heet a nd c ontac t the place of purchase to arrange for replacement parts.
PARTS LIST
Canopy
1ea ∅6"*H1-3/4"
Chain
1ea 6ft 3.8mm 3ea P3 Orange 1ea 1/4-IP*H75mm
Chain connector
2ea 5.8*H61mm 1ea 1-1/4"*H42mm 1ea W4-1/8"*E1"*H5mm
Bottom cap (T)
1ea 1-1/2"*H5mm 1ea 2-1/4"*H42mm 1ea 1-1/2"*H5mm
Finial Nipple
1ea 1-1/4"*H49mm 1ea 1/8-IP*H55mm 1ea 4"*H300mm
Part Needed Quantity
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
Company Name:_______________________Co. Account #:_____________
to be filled out by retailer
Mounting Screws Top loop
2ea 8#32-IP*1" 1ea 1/4-IP*H60mm
Wire connectors
Canopy loop
with Collar
Crystal ball
Nipple
Mounting strap
Bottom cap (W)
Center column
F
Read and review installation instruction sheet
before assembling the fixture.
ASSEMBLING THE FIXTURE (Fig.1)
1. Thread the Center Column (L1) to connector (R) till
tight.
2. Feed the fixture wires through the Top loop (J) and
pull the wires until taut.
3. Then screw the Top Loop (J) to the threaded center
column of Frame (M) until tight.
AFTER THE FIXTURE IS HUNG.
IXTURE ASSEMBLY INSTRUCTIONS
8118-M3 PW
Fig 1
NSTALL THE GLASS ASSEMBLY
For Customer Service, contact the place of purchase to arrange for replacement parts.
Page 2
Fig 2
PARTS & ASSEMBLY SHEET
Fixture Name: Alston Place 8118-M3 PW
ASSEMBLING THE FIXTURE (Fig.2)
4. By measuring determine correct number of links
needed for proper hanging height. Use a pair of pliers
to open one link of the Chain (C2) then remove the
excess Chain (C2) and discard it.
5. Use one chain connector (E2) to attach one end of
the chain to the Top loop (D2) and close the chain
connector.
6. Feed the fixture wires through the Chain (every
three links) and pull the wires until taut.
7. Slip Canopy loop collar (B2) over the chain, then do
the same with the canopy (F2).
8. When ready to complete the installation Use the
other chain connector and attach the other end of the
chain to the canopy loop (A2) and close the chain
connector.
9. Make sure the weight of the chandelier will be
supported by the chain-not the electrical wire.
* You may now install the fixture.
Note: Complete these remaining steps after the
fixture is hung.
10. Thread the Nipple (V) to connector (S),and slide
the Bottom cap (T), Crystal glass ball (U),Bottom cap
(W) on one by one, then use Finial (X) to thread tight.
11. Place the Glass Shades (O) over the Threaded
sockets (P),secure the Glass Shades (O) by threading
by the Socket Rings (N) until tight.
12. Install the light bulbs in accordance with the
fixture's specifications.
(DO NOT EXCEED MAXIMUM WATTAGE RATING)
For Customer Service, contact the place of purchase to arrange for replacement parts.
Page 3
one half of the canopy loop exterior threads should be exposed.
wiring connections.
CONNECTING THE WIRES (Fig 2)
the wire connector onto the wires.
INSTALLATION INSTRUCTIONS
Fixture Name: Alston Place 8118-M3/D5/6/9/M1L PW
For Chandelier Light Fixture
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE (Fig.1)
1. Carefully remove the new fixture from the carton and the
yellow bag that holds all parts. Check that all parts are included
as shown in the illustration and parts list.
2. Shut off the power at the circuit breaker and remove old
fixture from ceiling, including the old mounting strap.
3. Thread Nipple(C) into Canopy Loop (F) until snug.
4. Thread other end of the Nipple (C) with Canopy Loop
attached into Mounting Strap (D).
5. Place Lock Washer (B) over end of Nipple (C) protruding
through Mounting Strap (D) and thread Hex Nuts (A) onto
Nipple until tight.
6. Take this mounting strap assembly and mount to ceiling
junction box with junction box Screws (E). Tighten screw
securely with screw driver.
7. Unscrew the Canopy loop collar(H )from the Canopy loop.
Take the canopy and pass over the Canopy loop. approximatly
Adjust until desired height is reached. *the Canopy loop collar
should fit snugly on the Canopy loop after the canopy is
installed. Remove Canopy and Canopy lock collar.
8. Assemble the fixture and have an assistant or secure
support hold the weight of the fixture while you complete the
Fig. 1
9.Thread the fixture wires and ground wire of the assembled
fixture through the canopy loop and nipple and into the outlet
box.
10. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to
WHITE (or RIBBED).
11. Attach the GROUND wire(GREEN or COPPER) from the
Junction Box and the fixture Ground wire to the green Ground
Screw on the Mounting Bracket (D) or connect both wires
together using the correct size of wire connectors.
NOTE: Twist the wires together in the same direction you twist
12. Tuck these wire connections neatly into the Junction Box.
13. Raise Canopy (G) to the ceiling and secure in place by
tightening the Canopy loop collar(H) into the Canopy Loop(F)
14. Install the light bulbs and glass shade as per the fixture
assembly sheet.
For Customer Service, contact the place of purchase to arrange for replacement parts.
Fig. 2
YOUR INSTALLATIO N I S NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX
AND TEST THE FIXTURE.
Loading...