Golden Lighting 8118-FM PW User Manual

Part Needed Quantity

Reason why ( missing, scratched, b r oken glass, bent, bad f inish)

Comments

PARTS & ASSEMBLY SHEET

Company Name:_______________________Co. Account #:_____________

to be filled out by retailer

Fixture Name: Alston Place 8118-FM BUS

This fixture assembled PO:__________ Date: ________

Notice: Please review the parts listing and check for al l parts before assembling the fixture. If any parts are missing or

damaged, please note on this sheet and contact the place of purchase to arrange for replacement parts.

PARTS LIST

Canopy Nipple

1ea ∅1-1/2"*H5mm 1ea 1/8-IP*H45mm 1ea 1/8-IP*H122mm

Finial Wire connectors

1ea ∅1-1/4"*H49mm 3ea P3 Orange

Mounting Strap Mounting Screws

1ea ∅4"*H10mm 2ea 8#32-IP*1" 2ea 5/32-IP*H3mm

Wire connectors

3ea P3 Orange

Hex Nut Rubber Washer

1ea 1/8-IP*H4mm 1ea ∅1-1/2*H2mm

Part Needed Quantity

Nipple

1ea ∅1"*H3mm

ROD

Mounting
Screws

2ea 8#32-IP*1-1/2"

Hex Nut

Flat washer

1ea ∅1-1/2*H2mm

FIXTURE ASSEMBLY INSTRUCTIONS

Read and review installation instruction sheet before
assembling the fixture.

8118-FM BUS

1. Thread the Nipple (K) into the fixture pan coupling (J).

2. Install the light bulbs in accordance with the fixture's
specifications.

3. Thread Nipple (S) into Rod (K). Slide Flat Washer (R)
and Glass (L) onto Nipple (S). Then put Cap (T), Rubber
Washer (M), and Flat washer (N) onto Nipple (S).

4. Thread Hex Nut (O) onto Nipple (S) to secure.

5. Slide Canopy (P) onto Nipple (S). Secure with Finial (Q).

DO NOT EXCEED MAXIMUM WATTAGE RATING!

Fig 4

NOTE: INSTALL THE GLASS ASSEMBLY AFTER

THE FIXTURE IS HUNG.

For Customer Service, contact the place of purchase to arrange for replacement parts.

8118-FMPartsInstallation_20111118m.xlsx

INSTALLATION INSTRUCTIONS

old fixture from ceiling, including the old mounting strap.
green Ground Screw (L) on the Mounting Bracket (E) or

8. Finish mounting the Ceiling Pan (J) by placing it over

Fig. 3

Fixture Name: Alston Place 8118-FM UBS

For Flush Mount L ight Fixture

WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.

HANGING THE FIXTURE (Fig.1)

1.Carefully remove the new fixture from the carton and
the yellow bag that holes all your parts. Check that all
parts are included as shown in the illustration and

list.

2. Shut off power at the circuit breaker and remove the

3. Thread the two Fixture Mounting Screws (G) into the
pre-drilled Holes in the Mounting Strap (

same distance apart as the holes in the ceiling pan.
Secure in place with Hex nuts (F).

E

4. Attach Mounting Strap (
the two Mounting Screws (

CONNECTING THE WIRES (Fig 2)

5. Attach the power supply wires to the fixture lead
wires by connecting BLACK to BLACK (or SMOOTH)
and WHITE to WHITE (or RIBBED).

6. Attach the GROUND wire(GREEN or COPPER) from
the Junction Box and the fixture Ground wire to the

) to the junction box using

D )

E) spaced the

parts

Fig. 1

Fig. 2

connect both wires together using a wire connector.
NOTE: Twist the wires together in the same direction
you twist the wire connector onto the wires.

7. Tuck these wire connections neatly into the Junction
Box.

FINISHING THE INSTALLATION

the Mounting Strap (E) as shown in Fig. 1. Rotate the
pan until the Mounting Screws (G) protrude through the
“Keyholes” located in the bottom of Ceiling Pan (J).
Using a screwdriver, secure the Ceiling Pan (D) by
screwing Mounting Screws (G) until tight.

9. Install the light bulbs in accordance to the fixture’s
specifications.

10. Install the glass shade according to the assembly
instructions.

YOUR INSTALLATION IS NOW COMPLETE. RETURN POWER TO THE JUNCTION BOX AND TEST THE FIXT URE .

For Customer Service, contact the place of purchase to arrange for replacement parts.