Golden Lighting 8118-BA4 PW User Manual

Company Name:_______________________Co. Account #:_____________

to be filled out by retailer

PARTS & ASSEMBLY SHEET

Fixture Name: Alston Place 8118-BA4 PW

This fixture assembled PO:__________ Date: ________

Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing

or damaged, please note on this sheet and contact the place of purchase to arrange for replacement parts.

PARTS LIST

Mounting Strap Mounting Screws Deco Nut

1ea ∅4"*H2mm 2ea 8#32-IP*1" 2ea 5/32-IP*H9mm

Wire connectors Mounting Screws Hex Nut

3ea P3 Orange 2ea 5/32-IP*7/8" 2ea 5/32-IP*H3mm

Cap Nipple

2ea ∅1-1/2"*H5mm 2ea 5/32-IP*H45mm 2ea ∅1-1/2"*H32mm

Finial

2ea ∅3/4"*H34mm

Part Needed Quantity
Part Needed Quantity

Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments

Crystal ball

FIXTURE ASSEMBLY INSTRUCTIONS

Read and review installation instruction sheet, but
do not install before assembling the fixture.

1. Thread Nipple (R) onto end of fixture bar. Put Cap
(S), then Crystal Ball (T) onto Nipple (R) and secure with
Finial (U).

2. Repeat for other side.

Fig 1

8118-BA4 PW

3. Slide the Glass Shade (J) over Socket ( I). Secure
Glass Shade (J) by threading the Socket Ring (O) onto
Socket (I) until tight.

4. Install the light bulb in accordance with the fixture's
specifications.
DO NOT EXCEED MAXIMUM WATTAGE RATING!

NOTE: INSTALL THE GLASS ASSEMBLY AFTER

THE FIXTURE IS HUNG.

For Customer Service, contact the place of purchase to arrange for rep lace ment p arts.

8118-BA4 PWPartsInstallation_20120330.xls

2. Shut off power at the circuit breaker and remove the old fixture

Fig. 2

INSTALLATION INSTRUCTIONS

Fixture Name: Alston Place 8118-BA4 PW

For Wall Mount Light Fixture

WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.

HANGING THE FIXTURE (Fig.1)

1. Carefully remove the new fixture from the carton and the
yellow bag that holes all your parts. Check that all parts are
included as shown in the illustration and parts list.

from wall, including the old mounting strap.

3. The Mounting Strap (F) contains several pairs of threaded
holes, find the pair of holes that match the holes spacing in your
fixture Back Plate(H) and thread the two Mounting Screws(D)
half way into the Mounting Strap (F) and secure with Hex Nut
(G).

4. Place the Mounting Strap (F)over the Junction Box (A )so the
Mounting Screw s(D) are vertical or horizontal, as required by
fixture type.

5. Attach the Mounting Strap (F) to the Junction Box using the
two mounting screws (H)and tighten securely with screw driver.

CONNECTING THE WIRES (Fig. 2)

6. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to
WHITE (or RIBBED).

7. Attach the GROUND wire(GREEN or COPPER) from the
Junction Box and the fixture Ground wire to the green Ground
Screw (I) on the Mounting Bracket (F) or connect both wires
together using a wire connector.
NOTE:Twist the wires together in the same direction you twist
the wire connector (L) onto the wires.

8. Tuck these wire connections neatly into the Junction Box.

Fig. 1

FINISHING THE INSTALLATION (Fig. 3)

9. After tucking these wire connections neatly into the Junction
Box, place the fixture Back Plate(H) over the two Mounting
Screws (B).

10. Secure the Back Plate (H) against the wall by threading two
Deco Nuts (P) over the two Mounting Screws (D) until tight as
shown on Fig.1.

11. Install the light bulbs and glass shade as per the fixture
assembly sheet.
YOUR INSTALLATION IS NOW COMPLETE. RETURN POWER
TO THE JUNCTION BOX AND TEST THE FIXTURE.

For Customer Service, contact the place of purchase to arrange for replacement parts.

Fig. 3