Page 1
1ea D 5-3/4"*H1-1/2" 2ea 8#32-IP*1" 1ea 1/8-IP*H60mm
1ea 6ft 3.8mm 3ea P3 Orange 1ea 1/4-IP*H60mm
2ea 5.8*H61mm 1ea 1-1/8"*H42mm 1ea W4-1/8"*E1"*H5mm
1ea D 1-1/2"*H5mm 1ea D2-1/4"*H42mm 1ea 1-1/2"*H5mm
1ea D1-1/4"*H49mm 1ea 1/8-IP*H55mm 1ea 4"*H473mm
Part Needed Quantity
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
FIXTURE ASSEMBLY INSTRUCTIONS
Finial
Nipple
Center column
Chain connector
Canopy loop
with Collar
Mounting strap
Chain
Bottom cap (T)
Crystal ball
Bottom cap (W)
This fixture assembled PO:__________ Date: ________
PARTS & ASSEMBLY SHEET
Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or damaged,
please note on this sheet and contact the place of purchase to arrange for replacement parts.
Fixture Name: Alston Place 8118-6 BUS
PARTS LIST
Company Name:_______________________Co. Account #:_____________
to be filled out by retailer
Canopy
Mounting Screws
Top loop
ASSEMBLING THE FIXTURE (Fig.1)
1. Thread the Center Column (L1) to connector (R) till tight.
2. Feed the fixture wires through the Top loop (J) and pull the
wires until taut.
3. Then screw the Top Loop (J) to the threaded center
column of Frame (M) until tight.
Fig 1
NOTE: INSTALL THE GLASS ASSEMBLY AFTER
THE FIXTURE IS HUNG.
Read and review installation instruction sheet before
assembling the fixture.
8118-6 BUS
Wire connectors
Nipple
For Customer Service, contact the place of purchase to arrange for replacement parts.
8118-6PartsInstallation_10032011m.xls
Page 2
For Customer Service, contact the place of purchase to arrange for replacement parts.
ASSEMBLING THE FIXTURE (Fig.2)
4. By measuring determine correct number of links needed
for proper hanging height. Use a pair of pliers to open one
link of the Chain (C2) then remove the excess Chain (C2)
and discard it.
5. Use one chain connector (E2) to attach one end of the
chain to the Top loop (D2) and close the chain connector.
6. Feed the fixture wires through the Chain (every three links)
and pull the wires until taut.
7. Slip Canopy loop collar (B2) over the chain, then do the
same with the canopy (F2).
8. When ready to complete the installation Use the other
chain connector and attach the other end of the chain to the
canopy loop (A2) and close the chain connector.
9. Make sure the weight of the chandelier will be supported
by the chain-not the electrical wire.
* You may now install the fixture.
Note: Complete these remaining steps after the fixture is
hung.
10. Thread the Nipple (V) to connector (S),and slide the
Bottom cap (T), Crystal glass ball (U),Bottom cap (W) on one
by one, then use Finial (X) to thread tight.
11. Place the Glass Shades (O) over the Threaded sockets
(P),secure the Glass Shades (O) by threading by the Socket
Rings (N) until tight.
12. Install the light bulbs in accordance with the fixture's
specifications.
(DO NOT EXCEED MAXIMUM WATTAGE RATING)
PARTS & ASSEMBLY SHEET
Fig 2
Fixture Name: Alston Place 8118-6 BUS
8118-6PartsInstallation_10032011m.xls
Page 3
7. Unscrew the Canopy loop collar(H )from the Canopy loop. Take the
canopy and pass over the Canopy loop. approximatly one half of the
canopy loop exterior threads should be exposed. Adjust until desired
height is reached. *the Canopy loop collar should fit snugly on the
Canopy loop after the canopy is installed. Remove Canopy and
Canopy lock collar.
8. Assemble the fixture and have an assistant or secure support hold the
weight of the fixture while you complete the wiring connections.
9.Thread the fixture wires and ground wire of the assembled fixture
through the canopy loop and nipple and into the outlet box.
CONNECTING THE WIRES (Fig 2)
10. Attach the power supply wires to the fixture lead wires by connecting
BLACK to BLACK (or SMOOTH) and WHITE to WHITE (or RIBBED).
11. Attach the GROUND wire(GREEN or COPPER) from the Junction
Box and the fixture Ground wire to the green Ground Screw on the
Mounting Bracket (D) or connect both wires together using the correct
size of wire connectors.
NOTE: Twist the wires together in the same direction you twist the wire
connector onto the wires.
12. Tuck these wire connections neatly into the Junction Box.
Fig. 2
13. Raise Canopy (G) to the ceiling and secure in place by tightening the
Canopy loop collar(H) into the Canopy Loop(F)
14. Install the light bulbs and glass shade as per the fixture assembly
sheet.
YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX AND
TEST THE FIXTURE.
For Customer Service, contact the place of purchase to arrange for replacement parts.
INSTALLATION INSTRUCTIONS
Fixture Name: Alston Place 8118-M3/D5/6/9/M1L BUS
For Chandelier Light Fixture
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE (Fig.1)
1. Carefully remove the new fixture from the carton and the yellow bag
that holds all parts. Check that all parts are included as shown in the
illustration and parts list.
2. Shut off the power at the circuit breaker and remove old fixture from
ceiling, including the old mounting strap.
3. Thread Nipple(C) into Canopy Loop (F) until snug.
4. Thread other end of the Nipple (C) with Canopy Loop attached into
Mounting Strap (D).
5. Place Lock Washer (B) over end of Nipple (C) protruding through
Mounting Strap (D) and thread Hex Nuts (A) onto Nipple until tight.
6. Take this mounting strap assembly and mount to ceiling junction box
with junction box Screws (E). Tighten screw securely with screw driver.
Fig. 1
Loading...