Golden Lighting 8106-FM CDB User Manual
strap
screws
Wire connectors
Finial
Green screws
Nipple
Bottom cap
Rubber washer
Part Needed
Quantity
Reason why
( missing, scratched, broken glass, bent, bad finish)
Comments
Company Name:_______________________Co. Account #:_____________
to be filled out by retailer
PARTS & ASSEMBLY SHEET
NOTE: I
2. Install the light bulbs in accordance with the fixture's
5. Slide Bottom Cap (L) over Nipple (G) and thread the
Fixture Name: Torbellino 8106-FM CDB
This fixture assembled PO:__________ Date: ________
Notice:
missing or damaged, please note onthis sheet and contact the place of purchase to arrange for replacement
parts.
Please review the parts listing and check for all parts before assembling the fixture. If any parts are
PARTS LIST
Mounting
1ea W25*100L*11H*1.5t 2ea 8/32T*1-1/4"L 3ea Orange
Hex nut
2ea Φ9*3.5tmm 1ea Φ29*44hmm 1ea Φ9*10mm
1ea Φ12*125mm 1ea Φ70*11H*0.6t 1ea Φ18*1.0t
Part Needed Quantity
Mounting
F
IXTURE ASSEMBLY INSTRUCTIONS
Read and review installation instruction sheet
before assembling the fixture.
1. Thread the Nipple (G) into the Coupling (E), and
then thread the Hex Nut (F) onto Nipple (G) until tight.
specifications.
3. Place Glass Shade (H) over the Ceiling Pan (D).
The Nipple (G)shall protrude the bottom hole of the
Glass Shade (H).
4. While holding the Glass Shade (H) slide washer(J)
over Nipple (G) and thread Hex nut (K) until tight.
Finial (M) until tight.
(DO NOT EXCEED THE MAXIMUM WATTAGE RATING)
NSTALL THE GLASS ASSEMBLY
AFTER THE FIXTURE IS HUNG.
Fig 1
E
H
L
8106-FM CDB
J
D
F
G
K
M
For Customer Service, contact the place of purchase to arrange for replacement parts.
INSTALLATION INSTRUCTIONS
）
from the Junction Box and the fixture Ground wire to
(B) or connect both wires together using the correct
Junction Box.
9. Install the light bulbs in accordance to the fixture’s
Fixture Name:
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE（Fig.1
1. Carefully remove the new fixture from the carton
and the yellow bag that holds all parts. Check that
all parts are included as shown in the illustration
and parts list.
2. Shut off power at the circuit breaker and remove
old fixture from ceiling, including the old mounting
strap.
3. Thread the two Fixture Mounting Screws (A) into
the pre-drilled Hole in the Mounting Strap (B)
spaced the same distance apart as the hole in the
Ceiling Pan.
4. Attach Mounting Strap (B) to the junction box
using the two Screws (C).
CONNECTING THE WIRES (Fig 2)
5. Attach the power supply wires to the fixture lead
wires by connecting BLACK to BLACK (or
SMOOTH) and WHITE to WHITE (or RIBBED).
6. Attach the GROUND wire(GREEN or COPPER)
Torbellino 8106-FM CDB
For Flush Mount Light Fixture
Fig. 1
Fig. 2
the green Ground Screw on the Mounting Bracket
size of wire connectors.
- NOTE:Twist the wires together in the same
direction you twist the wire connector onto the
wires.
7. Tuck these wire connections neatly into the
FINISHING THE INSTALLATION (Fig.3)
8. Finish mounting the Ceiling Pan (D) by placing it
over the Mounting Strap (B) as shown on FIG.1.
Rotate the Pan until the Mounting screws (A)
protrude through the “Keyholes” located in the
bottom of Ceiling Pan (D). Using a screw driver,
secure the Ceiling Pan (D) by screwing Mounting
Screws (A) until taut.
specifications.
10. Install the glass shade as per the assembly
instructions.
YOUR INSTALLATION IS NOW COMPLETE. RETURN
POWER TO THE JUNCTION BOX AND TEST THE
FIXTURE.
Fig. 3
E
H
L
J
D
F
G
K
M
For Customer Service, contact the place of purchase to arrange for replacement parts.
Loading...