Golden Lighting 8106-D5 CDB User Manual
Threaded rod
F
and pull the wires until taut.
PARTS & ASSEMBLY SHEET
Fixture Name: Torbellino 8106-D5 CDB
This fixture assembled PO:__________ Date: ________
Notice:
missing or damaged, please note onthis sheet and contact the place of purchase to arrange for
replacement parts.
PARTS LIST
Canopy Hex Nut
1ea Φ153*32Hmm 1ea Φ19mm*4mm 1ea Φ25*45Hmm
Chain
1ea 6ft 1ea Φ12*55mm 3ea Orange
Chain
connector
2ea 23.8*59mm 1ea 100mm*20mm , 1ea Φ9*10mm 2ea 8/32T*1-1/4"L
Part Needed Quantity
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
Please review the parts listing and check for all parts before assembling the fixture. If any parts are
Company Name:_______________________Co. Account #:_____________
to be filled out by retailer
Canopy loop
and Canopy
loop collar
Wire connectors
Mounting Strap
Mounting
Screws
IXTURE ASSEMBLY INSTRUCTIONS
Read and review installation instruction sheet before
assembling the fixture.
1. Feed the fixture wires through the Top loop (J)
2.Then screw the Top Loop (J) to the top of Frame
(K) until tight.
NOTE: I
AFTER THE FIXTURE IS HUNG.
NSTALL THE GLASS ASSEMBLY
For Customer Service, contact the place of purchase to arrange for replacement parts.
8106-D5 CDB
Fig 1
H
CHAIN
J
K
For Customer Service, contact the place of purchase to arrange for replacement parts.
9. Use one chain connector(E2) to attach one end of
11. Slip Canopy loop collar (B2) over the chain, then
supported by the chain-not the electrical wire.
6. Repeat with remaining arms and Deco screws.
* NOTE: The Finial can be scratched or broken if the
by threading the Finia l(N) onto the threaded rod (M)
PARTS & ASSEMBLY SHEET
Fixture Name: Torbellino 8106-D5 CDB
CHAIN
3. Unscrew two of the Deco screws (L) from the
Frame (K) and save.
4. Two arms are already attached to the Frame.
Gently spread the arms until evenly spaced.
5. Align the hole in lower side of Frame arm (K) with
hole Frame(K). Secure in place with the Deco
screw (L).
full weight of the fixture is placed on it. To avoid
damage attach Finial after hanging the fixture.
7. Attach Finial (N) to the base of fixture Frame (K)
until tight.
Fig 2
J
K
L
O
M
N
P
8. By measuring determine correct number of links
needed for proper hanging height. Use a pair of
pliers to open one link of the Chain (C2) then
remove the excess Chain (C2) and discard it.
the chain to the Top loop (D2) and close the chain
connector.
10. Feed the fixture wires through the Chain (every
three links) and pull the wires until taut.
do the same with the canopy (F2).
12. When ready to complete the installation Use the
other chain connector and attach the other end of
the chain to the canopy loop (A2) and close the
chain connector.
13. Make sure the weight of the chandelier is
* You may now install the fixture.
Fig 3
A2
B2
E2
C2
E2
D2
Note: Complete these remaining steps after the
fixture is hung.
14. Place the Glass Shade (P) over the Threaded
Socket (O),place the Socket washer (Q) over the
threaded socket (O) then secure the Glass Shade
(P) by threading by the Socket Ring (R) until tight.
15. Install the light bulbs in accordance with the
fixture's specifications.
(DO NOT EXCEED THE MAXIMUM WATTAGE RATING)
Fig 4
O
M
P
Q
R
Loading...