Page 1
Canopy loop
PARTS & ASSEMBLY SHEET
F
Fixture Name: Torbellino 8106-BP3 CDB
This fixture assembled PO:__________ Date: ________
Notice:
Please review the parts listing and check for all parts before assembling the fixture. If any parts are
missing or damaged, please note onthis sheet and contact the place of purchase to arrange for
replacement parts.
Company Name:_______________________Co. Account #:_____________
PARTS LIST
Canopy
1ea Φ153*32Hmm 2ea 8/32T*1-1/4"L 1ea Φ62*68Hmm
to be filled out by retailer
Mounting
Screws
Top loop
Chain Wire connectors Bottom cap
1ea 6ft*4.2mm 2ea Orange 1ea Φ70*11Hmm
Chain
connector
2ea 23.8*59mm 1ea Φ25*45Hmm 2ea Φ12*55mm
and Canopy
Nipple
Mounting Strap Hex Nut Finial
1ea 100mm*20mm 2ea Φ9mm*4mm 1ea Φ36*55Hmm
Part Needed Quantity
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
IXTURE ASSEMBLY INSTRUCTIONS
Read and review installation instruction sheet before
assembling the fixture.
1. Thread the Body (L) onto the Coupling (M) and
until tight.
2. Feed the fixture wires through the Top loop (J)
and pull the wires until taut.
3. Then screw the Top Loop (J) to the threaded
Nipple (K) at top of Frame until tight.
NOTE: I
NSTALL THE GLASS ASSEMBLY
AFTER THE FIXTURE IS HUNG.
For Customer Service, contact the place of purchase to arrange for replacement parts.
Fig 1
8106-BP3 CDB
N
R
X
J
K
L
P
M
S
T
S
U
V
W
Y
Page 2
Fixture Name: Torbellino 8106-BP3 CDB
PARTS & ASSEMBLY SHEET
For Customer Service, contact the place of purchase to arrange for replacement parts.
thread the Hex Nut (T) onto Nipple (S) until tight.
B2
A2
C2
E2
M
4. By measuring determine correct number of links needed
for proper hanging height. Use a pair of pliers to open one
link of the Chain (C2) then remove the excess Chain (C2)
and discard it.
5. Use one chain connector(E2) to attach one end of the
chain to the Top loop (D2) and close the chain connector.
6. Feed the fixture wires through the Chain (every three
links) and pull the wires until taut.
7. Slip Canopy loop collar (B2) over the chain, then do the
same with the canopy (F2).
8. When ready to complete the installation Use the other
chain connector and attach the other end of the chain to the
canopy loop (A2) and close the chain connector.
9. Make sure the weight of the chandelier is supported by
the chain-not the electrical wire.
Fig 2
E2
D2
You may now install the fixture.
NOTE: Complete these remaining steps after the fixture is
hung.
10. Thread the Nipple (S) into the Coupling (R), and then
11. Install the light bulbs in accordance with the fixture’s
specifications.
12. Place Glass Shade (N) over the Metal Ring (S). The
Nipple (S) shall protrude through the bottom hole of the
Glass Shade (U).
13. While holding the Glass Shade slide the Rubber
Washer (V) onto the Nipple(S).
14. Slide Bottom Cap (X) over Nipple (S) and thread the
Finial (Y) until tight.
15. Attach each half of the Diffuser (N) on the circular plate
of the Metal ring (S) using the Deco nuts (P) and rubber
washers attached. Place one rubber washer on each sied of
Fig 3
G
H
CHAIN
J
K
L
N
R
X
P
T
S
V
W
Y
S
U
the Diffuser glass (N) to protect from breakage.
(DO NOT EXCEED THE MAXIMUM WATTAGE RATING)
Page 3
INSTALLATION INSTRUCTIONS
the canopy and pass over the Canopy loop. approximatly one half of
box with junction box Screws (E). Tighten screw securely with screw
connecting BLACK to BLACK (or SMOOTH) and WHITE to WHITE
Fixture Name:
Torbellino 8106-BP3 CDB
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE (Fig.1)
1. Carefully remove the new fixture from the carton and the yellow
bag that holds all parts. Check that all parts are included as shown
in the illustration and parts list.
2. Shut off the power at the circuit breaker and remove old fixture
from ceiling, including the old mounting strap.
3. Thread Nipple(C) into Canopy Loop (F) until snug.
4. Thread other end of the Nipple (C) with Canopy Loop attached
into Mounting Strap (D).
5. Place Lock Washer (B) over end of Nipple (C) protruding through
Mounting Strap (D) and thread Hex Nuts (A) onto Nipple until tight.
6. Take this mounting strap assembly and mount to ceiling junction
driver.
7. Unscrew the Canopy loop collar (H) from the Canopy loop. Take
For Chandelier Light Fixture
Fig. 1
JUNCTION BOX
(CEILING)
A
B
D
C
E
F
G
the canopy loop exterior threads should be exposed. Adjust until
desired height is reached. *the Canopy loop collar should fit snugly
on the Canopy loop after the canopy is installed. Remove Canopy
and Canopy lock collar.
8. Assemble the fixture and have an assistant or secure support
hold the weight of the fixture while you complete the wiring
connections.
9. Thread the fixture wires and ground wire of the assembled fixture
through the canopy loop and nipple and into the outlet box.
CONNECTING THE WIRES (Fig 2)
10. Attach the power supply wires to the fixture lead wires by
(or RIBBED).
11. Attach the GROUND wire(GREEN or COPPER) from the
Junction Box and the fixture Ground wire to the green Ground
Screw on the Mounting Bracket (D) or connect both wires together
using the correct size of wire connectors.
- NOTE: Twist the wires together in the same direction you twist
the wire connector onto the wires.
12. Tuck these wire connections neatly into the Junction Box.
H
CHAIN
J
Fig. 2
13. Raise Canopy (G) to the ceiling and secure in place by
tightening the Canopy loop collar(H) into the Canopy Loop(F)
14. Install the light bulbs and glass shade as per the fixture
assembly sheet.
For Customer Service, contact the place of purchase to arrange for replacement parts.
YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX
AND TEST THE FIXTURE.
Loading...