Golden Lighting 8106-BA4 CDB User Manual
Finials
by threading the Socket Ring (H) onto the Threaded
PARTS & ASSEMBLY SHEET
Company Name:_______________________Co. Account #:_____________
I
D
Fixture Name: Torbellino 8106-BA4 CDB
This fixture assembled PO:__________ Date: ________
Notice:
parts are missing or damaged, please note onthis sheet and contact the place of purchase to
arrange for replacement parts.
PARTS LIST
Circular strap
1ea Φ102*1.5tmm 4ea 8/32T*1-1/4"L 3ea Orange
Hex nut Deco nut
2ea Φ9*3.5tmm 2ea Φ12*10hmm 2ea Φ36*55hmm
Part Needed Quantity
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
F
IXTURE ASSEMBLY INSTRUCTIONS
Read and review installation instruction sheet
before assembling the fixture.
Please review the parts listing and check for all parts before assembling the fixture. If any
to be filled out by retailer
Mounting
screws
Wire
connencors
8106-BA4 CDB
1. Attach the Finials (I) to each end of the bath bar
(J) by twisting in a clockwise direction.
2. Place the Glass Shade (F)over the Socket (G).
3. Holding the Glass Shade (F), place the Socket
Washer(I)over the Threaded Socket(G).
4. Secure Glass Shade (F) and Socket Washer (I)
Socket (G) until tight.
5. Install the light bulb in accordance with the
fixture's specifications.
(DO NOT EXCEED MAXIMUM WATTAGE RATING!)
NOTE: I
NSTALL THE GLASS ASSEMBLY
Fig 1
J
D
G
E
F
I
H
AFTER THE FIXTURE IS HUNG.
For Customer Service, contact the place of purchase to arrange for replacement parts.
4. Place the Mounting Strap(A)over the Junction Box
so the Mounting Screws(C) are vertical or horizontal,
Back Plate(D)against the wall by threading two Deco
INSTALLATION INSTRUCTIONS
E
E
Fixture Name:
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE (Fig.1)
1. Carefully remove the new fixture from the carton
and the yellow bag that holes all your parts. Check
that all parts are included as shown in the illustration
and parts list.
2. Shut off power at the circuit breaker and remove
the old fixture from wall, including the old mounting
strap.
3.The Mounting Strap(A) contains several pairs of
threaded holes, find the pair of holes that match the
holes spacing in your fixture Back Plate(D) and
thread the two Mounting Screws(C) half way into the
Mounting Strap(A).
as required by fixture type.
5. Attach the Mounting Strap(A) to the Junction Box
using the two mounting screws(B). Tighten the
screws(B) securely with screw driver.
Torbellino 8106-BA4 CDB
For Wall Mount Light Fixture
Fig. 1
JUNCTION BOX
B
C
A
D
CONNECTING THE WIRES (Fig 2)
6. Attach the power supply wires to the fixture lead
wires by connecting BLACK to BLACK (or
SMOOTH) and WHITE to WHITE (or RIBBED).
7. Attach the GROUND wire(GREEN or COPPER)
from the Junction Box and the fixture Ground wire to
the green Ground Screw on the Mounting Bracket
(B) or connect both wires together using the correct
size of wire connectors.
- NOTE:Twist the wires together in the same
direction you twist the wire connector onto the wires.
8. Tuck these wire connections neatly into the
Junction Box.
FINISHING THE INSTALLATION (Fig.3)
9. After tucking these wire connections neatly into
the Junction Box and place the fixture Back Plate(D)
over the two Mounting Screws(C) and secure the
Nuts(E) over the two Mounting Screws(C) until tight
as shown on Fig.1.
Fig. 2
Fig. 3
YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX AND
For Customer Service, contact the place of purchase to arrange for replacement parts.
D
Loading...