Golden Lighting 8106-BA3 CDB User Manual

Finials

Company Name:_______________________Co. Account #:_____________

PARTS & ASSEMBLY SHEET

Fixture Name: Torbellino 8106-BA3 CDB

This fixture assembled PO:__________ Date: ________

Notice:

parts are missing or damaged, please note onthis sheet and contact the place of purchase to
arrange for replacement parts.

PARTS LIST

Circular strap

1ea Φ102*1.5tmm 4ea 8/32T*1-1/4"L 3ea Orange

Hex nut Deco nut

2ea Φ9*3.5tmm 2ea Φ12*10hmm 2ea Φ36*55hmm

Part Needed Quantity

Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments

F

IXTURE ASSEMBLY INSTRUCTIONS

Read and review installation instruction sheet
before assembling the fixture.

Please review the parts listing and check for all parts before assembling the fixture. If any

to be filled out by retailer

Mounting
screws

Wire
connencors

8106-BA3 CDB

1. Attach the Finials(I) to each end of the bath

bar(J) by twisting in a clockwise direction.

2. Place the Glass Shade(F)over the Socket (G).

3. Holding the Glass Shade(F), place the Socket

Washer(I)over the Threaded Socket(G).

4. Secure Glass Shade(F) and Socket Washer (I)

by threading the Socket Ring(H) onto the Threaded

Socket(G) until tight.

5. Install the light bulb in accordance with the

fixture's specifications.

(DO NOT EXCEED MAXIMUM WATTAGE RATING!)

NOTE: I

NSTALL THE GLASS ASSEMBLY

Fig 1

D

G

E

F

I

H

J

AFTER THE FIXTURE IS HUNG.

For Customer Service, contact the place of purchase to arrange for replacement parts.

INSTALLATION INSTRUCTIONS

and the yellow bag that holes all your parts. Check that

or connect both wires together using the correct size of

8. Tuck these wire connections neatly into the Junction

E

E

Fixture Name:

WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.

HANGING THE FIXTURE (Fig.1)

1. Carefully remove the new fixture from the carton

all parts are included as shown in the illustration and
parts list.

2. Shut off power at the circuit breaker and remove the
old fixture from wall, including the old mounting strap.

3.The Mounting Strap(A) contains several pairs of
threaded holes, find the pair of holes that match the
holes spacing in your fixture Back Plate(D) and thread
the two Mounting Screws(C) half way into the
Mounting Strap(A).

4. Place the Mounting Strap(A)over the Junction Box
so the Mounting Screws(C) are vertical or horizontal,
as required by fixture type.

5. Attach the Mounting Strap(A) to the Junction Box
using the two mounting screws(B). Tighten the
screws(B) securely with screw driver.

Torbellino 8106-BA3 CDB

For Wall Mount Light Fixture

Fig. 1

JUNCTION BOX

C

A

B

D

CONNECTING THE WIRES (Fig 2)

6. Attach the power supply wires to the fixture lead
wires by connecting BLACK to BLACK (or SMOOTH)
and WHITE to WHITE (or RIBBED).

7. Attach the GROUND wire(GREEN or COPPER)
from the Junction Box and the fixture Ground wire to
the green Ground Screw on the Mounting Bracket (B)

wire connectors.

- NOTE:Twist the wires together in the same direction
you twist the wire connector onto the wires.

Box.

FINISHING THE INSTALLATION (Fig.3)

9. After tucking these wire connections neatly into the
Junction Box and place the fixture Back Plate(D) over
the two Mounting Screws(C) and secure the Back
Plate(D)against the wall by threading two Deco
Nuts(E) over the two Mounting Screws(C) until tight as
shown on Fig.1.

Fig. 2

Fig. 3

YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX AND
TEST THE FIXTURE.

For Customer Service, contact the place of purchase to arrange for replacement parts.

D