Golden Lighting 8106-BA2 CDB User Manual
Finials
PARTS & ASSEMBLY SHEET
Company Name:_______________________Co. Account #:_____________
Fixture Name: Torbellino 8106-BA2 CDB
This fixture assembled PO:__________ Date: ________
Notice:
parts are missing or damaged, please note onthis sheet and contact the place of purchase to
arrange for replacement parts.
PARTS LIST
Circular strap
1ea Φ102*1.5tmm 4ea 8/32T*1-1/4"L 3ea Orange
Hex nut Deco nut
2ea Φ9*3.5tmm 2ea Φ12*10hmm 2ea Φ36*55hmm
Part Needed Quantity
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
F
IXTURE ASSEMBLY INSTRUCTIONS
Read and review installation instruction sheet
before assembling the fixture.
Please review the parts listing and check for all parts before assembling the fixture. If any
to be filled out by retailer
Mounting
screws
Wire
connencors
8106-BA2 CDB
1. Attach the Finials(I) to each end of the bath
bar(J) by twisting in a clockwise direction.
2. Place the Glass Shade(F)over the Socket (G).
3. Holding the Glass Shade(F), place the Socket
Washer(I)over the Threaded Socket(G).
4. Secure Glass Shade(F) and Socket Washer (I)
by threading the Socket Ring(H) onto the Threaded
Socket(G) until tight.
5. Install the light bulb in accordance with the
fixture's specifications.
(DO NOT EXCEED MAXIMUM WATTAGE RATING!)
NOTE: I
NSTALL THE GLASS ASSEMBLY
Fig 1
D
G
E
J
I
F
I
H
AFTER THE FIXTURE IS HUNG.
For Customer Service, contact the place of purchase to arrange for replacement parts.
horizontal, as required by fixture type.
TEST THE FIXTURE.
INSTALLATION INSTRUCTIONS
E
E
Fixture Name:
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE(Fig.1)
1.Carefully remove the new fixture from the
carton and the yellow bag that holes all your
parts. Check that all parts are included as shown
in the illustration and parts list.
2. Shut off power at the circuit breaker and
remove the old fixture from wall, including the old
mounting strap.
3.The Mounting Strap(A) contains several pairs
of threaded holes, find the pair of holes that
match the holes spacing in your fixture Back
Plate(D) and thread the two Mounting Screws(C)
half way into the Mounting Strap(A).
4.Place the Mounting Strap(A)over the Junction
Box so the Mounting Screws(C) are vertical or
5.Attach the Mounting Strap(A) to the Junction
Box using the two mounting screws(B). Tighten
the screws(B) securely with screw driver.
Torbellino 8106-BA2 CDB
For Wall Mount Light Fixture
Fig. 1
JUNCTION BOX
B
C
A
D
CONNECTING THE WIRES (Fig 2)
6. Attach the power supply wires to the fixture
lead wires by connecting BLACK to BLACK (or
SMOOTH) and WHITE to WHITE (or RIBBED).
7. Attach the GROUND wire(GREEN or
COPPER) from the Junction Box and the fixture
Ground wire to the green Ground Screw on the
Mounting Bracket (B) or connect both wires
together using the correct size of wire
connectors. -
NOTE:Twist the wires together in the same
direction you twist the wire connector onto the
wires.
8. Tuck these wire connections neatly into the
Junction Box.
FINISHING THE INSTALLATION(Fig.3)
9. After tucking these wire connections neatly
into the Junction Box and place the fixture Back
Plate(D) over the two Mounting Screws(C) and
secure the Back Plate(D) against the wall by
threading two Deco Nuts(E) over the two
Mounting Screws(C) until tight as shown on
Fig.1.
YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX AND
Fig. 2
Fig. 3
D
For Customer Service, contact the place of purchase to arrange for replacement parts.
Loading...