Golden Lighting 8106-BA1 CDB User Manual

Green screw

Part Needed

Quantity

Reason why

( missing, scratched, broken glass, bent, bad finish)

Comments

Company Name:_______________________Co. Account #:_____________

to be filled out by retailer

PARTS & ASSEMBLY SHEET

NOTE: I

by threading the Socket Ring (H) onto the Threaded

Fixture Name: Torbellino 8106-BA1 CDB

This fixture assembled PO:__________ Date: ________

Notice:

parts are missing or damaged, please note onthis sheet and contact the place of purchase to
arrange for replacement parts.

Please review the parts listing and check for all parts before assembling the fixture. If any

PARTS LIST

Circular strap

1ea Φ102*1.5tmm 4ea 8/32T*1-1/4"L 3ea Orange

Hex nut Deco nut

2ea Φ9*3.5tmm 2ea Φ12*10hmm 1ea Φ9*10mm

Part Needed Quantity

F

IXTURE ASSEMBLY INSTRUCTIONS

Read and review installation instruction sheet
before assembling the fixture.

Mounting
screws

Wire
connencors

8106-BA1 CDB

Fig 1

1. Place the Glass Shade (F)over the Socket (G).

2.Holding the Glass Shade (F), place the Socket

Washer (I)over the Threaded Socket (G).

H

I

3. Secure Glass Shade (F) and Socket Washer (I)

Socket (G) until tight.

4. Install the light bulb in accordance with the

fixture's specifications.

(DO NOT EXCEED MAXIMUM WATTAGE RATING!)

NSTALL THE GLASS ASSEMBLY

AFTER THE FIXTURE IS HUNG.

For Customer Service, contact the place of purchase to arrange for replacement parts.

D

E

F

G

INSTALLATION INSTRUCTIONS

in the illustration and parts list.

horizontal, as required by fixture type.

Fig.3.

Fixture Name:

WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.

HANGING THE FIXTURE(Fig.1)

1.Carefully remove the new fixture from the
carton and the yellow bag that holes all your
parts. Check that all parts are included as shown

2. Shut off power at the circuit breaker and
remove the old fixture from wall, including the old
mounting strap.

3.The Mounting Strap(A) contains several pairs
of threaded holes, find the pair of holes that
match the holes spacing in your fixture Back
Plate(D) and thread the two Mounting Screws(C)
half way into the Mounting Strap(A).

4.Place the Mounting Strap(A)over the Junction
Box so the Mounting Screws(C) are vertical or

Torbellino 8106-BA1 CDB

For Wall Mount Light Fixture

Fig. 1

5.Attach the Mounting Strap(A) to the Junction
Box using the two mounting screws(B). Tighten
the screws(B) securely with screw driver.

CONNECTING THE WIRES (Fig 2)

6. Attach the power supply wires to the fixture
lead wires by connecting BLACK to BLACK (or
SMOOTH) and WHITE to WHITE (or RIBBED).

7. Attach the GROUND wire(GREEN or
COPPER) from the Junction Box and the fixture
Ground wire to the green Ground Screw on the
Mounting Bracket (B) or connect both wires
together using the correct size of wire
connectors. -
NOTE:Twist the wires together in the same
direction you twist the wire connector onto the
wires.

8. Tuck these wire connections neatly into the

FINISHING THE INSTALLATION(Fig.3)

9. After tucking these wire connections neatly
into the Junction Box and place the fixture Back
Plate(D) over the two Mounting Screws(C) and
secure the Back Plate(D)against the wall by
threading two Deco Nuts(E) over the two
Mounting Screws(C) until tight as shown on

Fig. 2

Fig. 3

YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX AND
TEST THE FIXTURE.

For Customer Service, contact the place of purchase to arrange for replacement parts.