
PARTS & ASSEMBLY SHEET
and pull the wires until taut.
Fixture Name: Torbellino 8106-6 CDB
This fixture assembled PO:__________ Date: ________
Notice:
missing or damaged, please note onthis sheet and contact the place of purchase to arrange for
replacement parts.
PARTS LIST
Canopy Hex Nut
1ea Φ153*32Hmm 1ea Φ19mm*4mm 1ea Φ25*45Hmm
Chain
1ea 6ft 1ea Φ12*55mm 3ea Orange
Chain
connector
2ea 23.8*59mm 1ea 100mm*20mm , 1ea Φ9*10mm 2ea 8/32T*1-1/4"L
Part Needed Quantity
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
Please review the parts listing and check for all parts before assembling the fixture. If any parts are
Company Name:_______________________Co. Account #:_____________
to be filled out by retailer
Canopy loop
and Canopy
loop collar
Wire connectors
Mounting Strap
Mounting
Screws
IXTURE ASSEMBLY INSTRUCTIONS
Read and review installation instruction sheet before
assembling the fixture.
1. Feed the fixture wires through the Top loop (J)
2.Then screw the Top Loop (J) to the top of Frame
(K) until tight.
NOTE: I
NSTALL THE GLASS ASSEMBLY
AFTER THE FIXTURE IS HUNG.
For Customer Service, contact the place of purchase to arrange for replacement parts.
8106-6 CDB
Fig 1
H
CHAIN
J
K

PARTS & ASSEMBLY SHEET
Fixture Name: Torbellino 8106-6 CDB
14. Place the Glass Shade (P) over the Threaded Socket
For Customer Service, contact the place of purchase to arrange for replacement parts.
12. When ready to complete the installation Use the other
3. Unscrew four of the Deco screws (L) from the Frame
(K) and save.
4. Two arms are already attached to the Frame. Gently
spread the remaining four arms until evenly spaced.
5. Align the hole in lower side of Frame arm (K) with hole
Frame(K). Secure in place with the Deco screw (L).
6. Repeat with remaining arms and Deco screws.
* NOTE: The Finial can be scratched or broken if the full
weight of the fixture is placed on it. To avoid damage
attach Finial after hanging the fixture.
7. Attach Finial (N) to the base of fixture Frame (K) by
threading the Finia l(N) onto the threaded rod (M) until
tight
8. By measuring determine correct number of links
needed for proper hanging height. Use a pair of pliers to
open one link of the Chain (C2) then remove the excess
Chain (C2) and discard it.
Fig 2
Fig 3
J
K
R
Q
P
O
L
M
N
A2
B2
9. Use one chain connector(E2) to attach one end of the
chain to the Top loop (D2) and close the chain connector.
10. Feed the fixture wires through the Chain (every three
links) and pull the wires until taut.
11. Slip Canopy loop collar (B2) over the chain, then do
the same with the canopy (F2).
chain connector and attach the other end of the chain to
the canopy loop (A2) and close the chain connector.
13. Make sure the weight of the chandelier is supported
by the chain-not the electrical wire.
* You may now install the fixture..
Note: Complete these remaining steps after the fixture is
hung.
(O),place the Socket washer (Q) over the threaded
socket (O) then secure the Glass Shade (P) by threading
by the Socket Ring (R) until tight.
15. Install the light bulbs in accordance with the fixture's
specifications.
(DO NOT EXCEED THE MAXIMUM WATTAGE RATING)
E2
C2
E2
D2
Fig 4
R
Q
P
O

2. Shut off the power at the circuit breaker and remove old fixture
junction box with junction box Screws (E). Tighten screw securely
should fit snugly on the Canopy loop after the canopy is installed.
INSTALLATION INSTRUCTIONS
Fixture Name:
Torbellino 8106-6, -9, -D5, -M1L CDB
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE (Fig.1)
1. Carefully remove the new fixture from the carton and the
yellow bag that holds all parts. Check that all parts are included
as shown in the illustration and parts list.
from ceiling, including the old mounting strap.
3. Thread Nipple(C) into Canopy Loop (F) until snug.
4. Thread other end of the Nipple (C) with Canopy Loop attached
into Mounting Strap (D).
5. Place Lock Washer (B) over end of Nipple (C) protruding
through Mounting Strap (D) and thread Hex Nuts (A) onto Nipple
until tight.
6. Take this mounting strap assembly and mount to ceiling
with screw driver.
7. Unscrew the Canopy loop collar (H) from the Canopy loop.
Take the canopy and pass over the Canopy loop. approximatly
one half of the canopy loop exterior threads should be exposed.
Adjust until desired height is reached. *the Canopy loop collar
Remove Canopy and Canopy lock collar.
8. Assemble the fixture and have an assistant or secure support
hold the weight of the fixture while you complete the wiring
connections.
9. Thread the fixture wires and ground wire of the assembled
fixture through the canopy loop and nipple and into the outlet
box.
CONNECTING THE WIRES (Fig 2)
10. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to
WHITE (or RIBBED).
11. Attach the GROUND wire(GREEN or COPPER) from the
Junction Box and the fixture Ground wire to the green Ground
Screw on the Mounting Bracket (D) or connect both wires
together using the correct size of wire connectors.
- NOTE: Twist the wires together in the same direction you
twist the wire connector onto the wires.
12. Tuck these wire connections neatly into the Junction Box.
For Chandelier Light Fixture
Fig. 1
JUNCTION BOX
(CEILING)
A
B
D
C
E
F
G
H
CHAIN
J
Fig. 2
13. Raise Canopy (G) to the ceiling and secure in place by
tightening the Canopy loop collar(H) into the Canopy Loop(F)
14. Install the light bulbs and glass shade as per the fixture
assembly sheet.
For Customer Service, contact the place of purchase to arrange for replacement parts.
YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX
AND TEST THE FIXTURE.