Page 1
Canopy
Top loop
Wire connectors
loop collar
Nipple
Mounting Strap
Hex Nut
Finial
F
until tight.
Read and review installation instruction sheet before
PARTS & ASSEMBLY SHEET
Fixture Name: Torbellino 8106-3P CDB
This fixture assembled PO:__________ Date: ________
Notice:
missing or damaged, please note onthis sheet and contact the place of purchase to arrange for
replacement parts.
PARTS LIST
1ea Φ153*32Hmm 2ea 8/32T*1-1/4"L 1ea Φ62*68Hmm
Chain
1ea 6ft*4.2mm 2ea Orange 1ea Φ70*11Hmm
Chain
connector
2ea 23.8*59mm 1ea Φ25*45Hmm 2ea Φ12*55mm
1ea 100mm*20mm 2ea Φ9mm*4mm 1ea Φ36*55Hmm
Part Needed Quantity
Please review the parts listing and check for all parts before assembling the fixture. If any parts are
Company Name:_______________________Co. Account #:_____________
to be filled out by retailer
Mounting
Screws
Bottom cap
Canopy loop
and Canopy
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
IXTURE ASSEMBLY INSTRUCTIONS
assembling the fixture.
Fig 1
8106-3P CDB
1. Thread the Body (L) onto the Coupling (M) and
2. Then screw the Top Loop (J) to the threaded
L
Nipple (K) at top of Frame until tight.
M
J
K
NOTE: INSTALL THE GLASS ASSEMBLY
AFTER THE FIXTURE IS HUNG.
For Customer Service, contact the place of purchase to arrange for replacement parts.
N
Page 2
For Customer Service, contact the place of purchase to arrange for replacement parts.
4. Use one chain connector(E2) to attach one end of
supported by the chain-not the electrical wire.
PARTS & ASSEMBLY SHEET
Fixture Name: Torbellino 8106-3P CDB
fixture is hung.
fixture’s specifications.
13. Slide Bottom Cap (U) over Nipple (P) and thread
the Finial (V) until tight.
B2
A2
C2
E2
3. By measuring determine correct number of links
needed for proper hanging height. Use a pair of
pliers to open one link of the Chain (C2) then
remove the excess Chain (C2) and discard it.
the chain to the Top loop (D2) and close the chain
connector.
5. Feed the fixture wires through the Chain (every
three links) and pull the wires until taut.
6. Slip Canopy loop collar (B2) over the chain, then
do the same with the canopy (F2).
7. When ready to complete the installation Use the
other chain connector and attach the other end of
the chain to the canopy loop (A2) and close the
chain connector.
8. Make sure the weight of the chandelier is
Fig 2
E2
D2
You may now install the fixture.
NOTE: Complete these remaining steps after the
9. Thread the Nipple (P) into the Coupling (N), and
then thread the Hex Nut (Q) onto Nipple (P) until
tight.
10. Install the light bulbs in accordance with the
11. Place Glass Shade (R) over the Metal Ring .
The Nipple (P) shall protrude through the bottom
hole of the Glass Shade (R).
12. While holding the Glass Shade slide the
(DO NOT EXCEED THE MAXIMUM WATTAGE
Fig 3
G
H
L
M
Q
S
T
V
CHAIN
J
K
N
P
R
V
U
RATING)
Page 3
Screw on the Mounting Bracket (D) or connect both wires together
Take the canopy and pass over the Canopy loop. approximatly one
INSTALLATION INSTRUCTIONS
Fixture Name:
Torbellino 8106-3P CDB
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE (Fig.1)
1. Carefully remove the new fixture from the carton and the yellow
bag that holds all parts. Check that all parts are included as shown
in the illustration and parts list.
2. Shut off the power at the circuit breaker and remove old fixture
from ceiling, including the old mounting strap.
3. Thread Nipple(C) into Canopy Loop (F) until snug.
4. Thread other end of the Nipple (C) with Canopy Loop attached
into Mounting Strap (D).
5. Place Lock Washer (B) over end of Nipple (C) protruding
through Mounting Strap (D) and thread Hex Nuts (A) onto Nipple
until tight.
6. Take this mounting strap assembly and mount to ceiling junction
box with junction box Screws (E). Tighten screw securely with
screw driver.
7. Unscrew the Canopy loop collar (H) from the Canopy loop.
For Chandelier Light Fixture
Fig. 1
JUNCTION BOX
(CEILING)
A
B
D
C
E
F
G
half of the canopy loop exterior threads should be exposed. Adjust
until desired height is reached. *the Canopy loop collar should fit
snugly on the Canopy loop after the canopy is installed. Remove
Canopy and Canopy lock collar.
8. Assemble the fixture and have an assistant or secure support
hold the weight of the fixture while you complete the wiring
connections.
9. Thread the fixture wires and ground wire of the assembled
fixture through the canopy loop and nipple and into the outlet box.
CONNECTING THE WIRES (Fig 2)
10. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to
WHITE (or RIBBED).
11. Attach the GROUND wire(GREEN or COPPER) from the
Junction Box and the fixture Ground wire to the green Ground
using the correct size of wire connectors.
- NOTE: Twist the wires together in the same direction you twist
the wire connector onto the wires.
12. Tuck these wire connections neatly into the Junction Box.
H
CHAIN
J
Fig. 2
13. Raise Canopy (G) to the ceiling and secure in place by
tightening the Canopy loop collar(H) into the Canopy Loop(F)
14. Install the light bulbs and glass shade as per the fixture
assembly sheet.
For Customer Service, contact the place of purchase to arrange for replacement parts.
YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX
AND TEST THE FIXTURE.
Loading...