Page 1
PARTS & ASSEMBLY SHEET
_
Fixture Name: Heartwood 8063-363 BUS
This fixture assembled PO:__________ Date: ________
Notice: Please review the parts listing and check for all parts before assembling the fixture. If
any parts are missing or damaged, please note onthis sheet and contact the place of purchase
to arrange for replacement parts.
PARTS LIST
Canopy 1ea
Chain 6ft Threaded ring 1ea
Chain
connector
Mounting
Strap Hvy
Mounting
screws
Part Needed Quantity
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
2ea
1ea Hex Nut 3ea
2ea
Company Name:_______________________Co. Account #:________
to be filled out by retailer
Mounting
Screws
Canopy Loop
Collar
Wire
connectors
2ea Canopy loop 1ea
Bottom cap,
small
1ea
2ea Finial 1ea
Nipple-A
Nipple-B
Bottom
assembly
FIXTURE ASSEMBLY INSTRUCTIONS
Read and review installation instruction sheet,
but do not install before assembling the fixture.
8063-363 BUS
2ea
1ea
1ea
Fig 1
ASSEMBLING THE FIXTURE (Fig.1)
1. Feed the fixture wires through the Top loop
(J) and pull the wires until taut.
2.Then screw the Top Loop (J) to the threaded
center column of Frame (M) until tight.
NOTE: INSTALL THE GLASS ASSEMBLY
AFTER THE FIXTURE IS HUNG.
For Customer Service, contact the place of purchase to arrange for replacement parts.
Page 2
PARTS & ASSEMBLY SHEET
Fixture Name: Heartwood 8063-363 BUS
ASSEMBLING THE FIXTURE (Fig.2)
3. By measuring determine correct number of links
needed for proper hanging height. Use a pair of
pliers to open one link of the Chain (C2) then
remove the excess Chain (C2) and discard it.
4. Use one chain connector(E2) to attach one end of
the chain to the Top loop (D2) and close the chain
connector.
5. Feed the fixture wires through the Chain (every
three links) and pull the wires until taut.
6. Slip Canopy loop collar (B2) over the chain, then
do the same with the canopy (F2).
7. When ready to complete the installation Use the
other chain connector and attach the other end of
the chain to the canopy loop (A2) and close the
chain connector.
8. Feed the fixture wires through canopy loop (F)
and nipple(C) and pull until taut.
Fig 2
A2
B2
E2
C2
E2
D2
Note: Complete these remaining steps after the
fixture is hung.
9. Place the Bottom Assembly (R) onto the Fixture
Base(Q)with the threaded rod(Nipple-B) protruding
through the hole, secure the Bottom Assembly(R) to
the base by threading the Hex Nut(S) onto the
threaded rod until tight.
10.Place the Bottom Cap (T) onto the Hex
Nut(S),and secure by threading the Finial(U) until
tight.
11. Place the Glass Shade(O) over the Threaded
Socket(P), secure the Glass Shade(O) by threading
by the Socket Ring(N) until tight.
12. Install the light bulbs in accordance with the
fixture's specifications.
(DO NOT EXCEED MAXIMUM WATTAGE RATING)
Fig 3
For Customer Service, contact the place of purchase to arrange for replacement parts.
Page 3
INSTALLATION INSTRUCTIONS
Fixture Name: Heartwood 8063-363 BUS
For Chandelier Light Fixture
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE as Chain hung (Fig.1)
1. Carefully remove the new fixture from the carton and the
yellow bag that holds all parts. Check that all parts are included
as shown in the illustration and parts list.
2. Shut off the power at the circuit breaker and remove old
fixture from ceiling, including the old mounting strap.
3. Thread Nipple(C) into Canopy Loop (F) until snug.
4. Thread other end of the Nipple (C) with Canopy Loop
attached into Mounting Strap (D).
5. Place Lock Washer (B) over end of Nipple (C) protruding
through Mounting Strap (D) and thread Hex Nuts (A) onto Nipple
until tight.
6. Take this mounting strap assembly and mount to ceiling
junction box with junction box Screws (E). Tighten screw
securely with screw driver.
7. Unscrew the Canopy loop collar(H)from the Canopy loop.
Take the canopy and pass over the Canopy loop. approximatly
one half of the canopy loop exterior threads should be exposed.
Adjust until desired height is reached. *the Canopy loop collar
should fit snugly on the Canopy loop after the canopy is
installed. Remove Canopy and Canopy lock collar.
8. Assemble the fixture and have an assistant or secure support
hold the weight of the fixture while you complete the wiring
connections.
9.Thread the fixture wires and ground wire of the assembled
fixture through the canopy loop and nipple and into the outlet
box.
CONNECTING THE WIRES (Fig 2)
10. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to
WHITE (or RIBBED).
11. Attach the GROUND wire(GREEN or COPPER) from the
Junction Box and the fixture Ground wire to the green Ground
Screw on the Mounting Bracket (B) or connect both wires
together using the correct size of wire connectors. - NOTE:
Twist the wires together in the same direction you twist the wire
connector onto the wires.
12. Tuck these wire connections neatly into the Junction Box.
Fig. 1
* This fixture is close to 50lbs.
A fan brace is recommended for fixtures
50lbs or more.
Fig. 2
13. Raise Canopy (G) to the ceiling and secure in place by
tightening the Canopy loop collar(H) into the Canopy Loop(F)
YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX
14. Install the light bulbs and glass shade as per the fixture
assembly sheet.
AND TEST THE FIXTURE.
For Customer Service, contact the place of purchase to arrange for replacement parts.
Loading...