Golden Lighting 8063-1W BUS User Manual

INSTALLATION INSTRUCTIONS

Fixture Name: Heartwood 8063-1W BUS

For Wall Mount Light Fixture

WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.

HANGING THE FIXTURE(Fig.1)

1.Carefully remove the new fixture from the carton and the
yellow parts bag. Check that all parts are included as shown in
the illustration and parts list.

2. Shut off power at the circuit breaker and remove the old
fixture from wall, including the old mounting strap.

3.The Mounting Strap(F) contains several pairs of threaded
holes, find the pair of holes that match the holes spacing in your
fixture Back Plate(S) and thread the two Fixture Mounting
Screws(D) half way into the Fixture Mounting Strap(F) and
secure with Hex Nut (G).

4. Place the Mounting Strap(F)over the Junction Box so the
Fixture Mounting Screws(D) are vertical or horizontal, as
required by the fixture type.

5. Attach the Mounting Strap(F) to the Junction Box using the
two mounting screws(H). Tighten the screws(H) securely with
screw driver.

CONNECTING THE WIRES (Fig 2)

6. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to
WHITE (or RIBBED).

7. Attach the GROUND wire(GREEN or COPPER) from the
Junction Box and the fixture Ground wire to the green Ground
Screw on the Mounting Bracket (I) or connect both wires
together using the correct size of wire connectors.
NOTE:Twist the wires together in the same direction you twist
the wire connector onto the wires.

8. Tuck these wire connections neatly into the Junction Box.

Fig. 1

Fig. 2

FINISHING THE INSTALLATION(Fig.3)

9. After tucking these wire connections neatly into the Junction
Box and place the fixture Back Plate(S) over the two Mounting
Screws(D) and secure the Back Plate(S)against the wall by
threading two Deco Nuts(O) over the two Mounting Screws(H)
until tight as shown on Fig.3.

10. Install glass as per the fixture assembly instructions.

YOUR INSTALLATION IS NOW COMPLETE. RETURN
POWER TO THE JUNCTION BOX AND TEST THE FIXTURE.

For Customer Service, contact the place of purchase to arrange for replacement parts.

Fig. 3

_

PARTS & ASSEMBLY SHEET

Fixture Name: Heartwood 8063-1W BUS

This fixture assembled PO:__________ Date: ________

Notice: Please review the parts listing and check for all parts before assembling the fixture. If any

parts are missing or damaged, please note onthis sheet and contact the place of purchase to arrange
for replacement parts.

Company Name:_______________________Co. Account #:_________

PARTS LIST

to be filled out by retailer

Mounting Strap 1ea

Hex nut 2ea

Part Needed Quantity
Part Needed Quantity

Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments

Mounting
Screws

Wire
connectors

4ea Deco Nut 2ea

2ea Green Screw 1ea

FIXTURE ASSEMBLY INSTRUCTIONS

Read and review installation instruction sheet
before assembling the fixture.

Fig. 4

1. Place the fixture Back Plate ( S ), over the
threaded rod, so it protrude through the
hole in the Back Plate ( S ).

2. Thread the Deco Nut ( O ) onto the threaded
rod and continue turning until the Back Plate(J)
is snug against the wall .

3. Place the Glass Shade (Q) over the Threaded
Socket (R)

4. Holding the Glass Shade ( Q ), and secure it by
threading the Socket Ring ( P ) onto the Threaded
Socket ( R ) until tight .

5. Install the light bulbs in accordance with the
fixture's specification .

8063-1W BUS

(DO NOT EXCEED THE MAXIMUM WATTAGE RATING!)

NOTE: INSTALL THE GLASS ASSEMBLY

AFTER THE FIXTURE IS HUNG.

For Customer Service, contact the place of purchase to arrange for replacement parts.