Golden Lighting 7644-SF GA User Manual

Download

Page 1

Mounting strap (circular)

Junction box screw

2ea @3/8 x 3mm 1ea @3/8 x 65mm

Mounting strap

3 pcs

Part Needed Quantity

Reason why ( missing, scratched, broken glass, bent, bad finish)

Comments

This fixture assembled PO:__________ Date: ________

to be filled out by retailer

For Customer Service, contact the place of purchase to arrange for replacement parts.

Company Name:_______________________Co. Account #:_____________

Fig. 1

PARTS & ASSEMBLY SHEET

Read and review installation instruction sheet before assembling the fixture.

Notice:

Decorative Chain

Fixture Name: Mirabella 7644-SF GA

Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or

damaged, please note onthis sheet and contact the place of purchase to arrange for replacement parts.

PARTS LIST

Wire connectors Deco nut

1ea @4" 3ea P4 Orange 5ea 10x 9.5mm

Canopy

1ea @5-5/8"X1-5/8" 2ea 8/32" x 1" 1ea @3/8 x 50mm

Chain Mounting screw

1ea 6ft x3.8mm 2ea 8/32" x 1-1/4" 1ea @3/8 x 40mm x 5mm

Chain connector Hex nut Nipple

2ea @3X38mm

w/ ground screw 1ea 3/4"X4" 2ea @8/32" x 8mm

Part Needed Quantity

Screw

Top loop

Canopy loop with Collar

(CRYSET-7644-SF)

IXTURE ASSEMBLY INSTRUCTIONS

7644-SF GA

ASSEMBLING THE FIXTURE as Semi flush (Fig. 1)

1. Place shade (N) over the nipple of the Frame (M) and secure with Deco Nut (E).

2. Attach hooks at both ends of the Decorative Chain (O) to Frame (M) as shown in the diagram.

3. Install the light bulbs in accordance with the fixture's specifications.

(DO NOT EXCEED MAXIMUM WATTAGE RATING)

7644-SF GA PartsInstallation_20120406m(ok)

Page 2

For Customer Service, contact the place of purchase to arrange for replacement parts.

Fig 2

PARTS & ASSEMBLY SHEET

Fixture Name: Mirabella 7644-SF GA

ASSEMBLING THE FIXTURE as Chain hung (Fig. 2)

1. Remove the Circular st r ap from top of Fixture and replace the long mounting s cr ew s with two short screws to hold the Deco nuts (E) in place on the fixture Bottomop cap (M).

2. Feed the fixture wires thr ough the Top loop (J) and pull the wires until taut.

3. Then screw the Top Loop (J) to the threaded center column of Frame (M) until tight.

4. Place shade (N) over t he nipple of the Frame (M) and secure Deco Nut (E).

5. By measuring determine correct number of links needed for proper hanging height. Use a pair of pliers to open one link of the Chain (K) then remove the excess Chain (K) and discard it.

6. Use one chain connector (L) to attach one end of the chain to the Top loop (J) and close the chain connector.

7. Feed the fixture wires thr ough the Chain (every three links) and pull the wires until t aut.

8. Slip Canopy loop collar (H) over the chain, then do the same with the canopy ( G).

9. When ready to complete the installation Use the other chain connector and attach the other end of the chain to the canopy loop (F) and close the chain connector.

10. Make sure the weight of the chandelier will be supported by the chain-not the electrical wire.

* You may now install the fixture. Note: Complete these remaining steps after the fixture is hung.

11. Pull the straight edges of the hook that sits at the end of decorative chain (N) outward until it opens, insert crystal ball (Q) into the opening and then close the hook by pressing the edges together over the loop at the top of the crystal as shown in the diagram.

12. Install the light bulbs (not provided) in accordance with the fixture's specifications.

(DO NOT EXCEED MAXIMUM WATTAGE RATING)

7644-SF GA PartsInstallation_20120406m(ok)

Page 3

Fig. 2

INSTALLATION INSTRUCTIONS

HANGING THE FIXTURE as Semi flush (Fig. 1)

Fig. 1

CONNECTING THE WIRES (Fig. 2)

BLACK to BLACK (or SMOOTH) and WHITE to WHITE (or RIBBED).

NOTE: Twist the wires together in the same direction you twist the wire

FINISHING THE INSALLATION (Fig.3)

against the ceiling by threading the decorative nuts on (E) until tight.

THE JUNCTION BOX AND TEST THE FIXTURE.

Fig. 3

BARE COPPER

(Ground)

GREEN (Ground)

FIXTURE WIRES

SMOOTH (BLACK)

RIBBED (WHITE)

BLACK

WHITE

HOUSE WIRES

Fixture Name: Mirabella 7644-SF GA

WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.

1. Carefully remove the new fixture from the carton and the yellow bag that holds all your parts. Check that all parts are included as shown in the illustration and parts list.

2. Shut off power at the circuit breaker and remove the old fixture from ceiling, including the old mounting strap.

3. The Circular Strap (B) contains several pairs of threaded holes, find the pair of holes that match the hole spacing in your fixture Canopy (F) and thread the two Mounting Screws (A) half way into the Mounting Strap (A) facing down, Secure in place with hex nuts. These will have their threaded ends protrude through the two holes in the fixture canopy(F).

4. Place the Mounting Strap (B) over the junction box.

5. Attach the Mounting Strap (B) to the Junction Box using the two mounting screws (C). Tighten the screws (C) securely with screw driver.

For Semi Flush / Convertible Light Fixture

6. Attach the power supply wires to the fixture lead wires by connecting

7. Attach the GROUND wire(GREEN or COPPER) from the Junction Box and the fixture Ground wire to the green Ground Screw on the Mounting Bracket (B) or connect both wires together using the correct size of wire connectors.

connector onto the wires.

8. Tuck these wire connections neatly into the Junction Box.

9. Place the fixture’s Canopy (F) over the Mounting Strap (B) and over the Mounting Screws (A), adjust the fixture Canopy until the Mounting Screws (A) protrude out from the canopy (D) and secure the fixture

10. Install the light bulbs and glass shade as per the fixture assembly sheet. YOUR INSTALLATION IS NOW COMPLETE. RETURN POWER TO

For Customer Service, contact the place of purchase to arrange for replacement parts.

Page 4

Fig. 2

For Customer Service, contact the place of purchase to arrange for replacement parts.

13. Raise Canopy (G) t o the ceiling and secur e in place by tightening the

14. Install the light bulbs and glass shade as per the fixture assembly sheet.

INSTALLATION INSTRUCTIONS

canopy loop and nipple and into the outlet box.

CONNECTING THE WIRES (Fig 2)

BLACK to BLACK (or SMOOTH) and W H ITE to WHITE (or RIBBED).

HANGING THE FIXTURE (Fig.1)

junction box Screws (E). Tighten screw securely with screw driver.

Fig. 1

JUNCTION BOX (CEILING)

E F

CHAIN

BARE COPPER

(Ground)

GREEN (Ground)

FIXTURE WIRES

SMOOTH (BLACK)

RIBBED (WHITE)

BLACK

WHITE

HOUSE WIRES

Fixture Name: Mirabella 7644-SF GA

For Chandelier Light Fixture

WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.

HANGING THE FIXTURE (Fig. 1)

1. Carefully remove the new fixture fr om the carton and the yellow

1. Carefully remove the new fixture from the c arton and the yellow bag that

bag that holds all parts. Check that all parts are included as shown in

holds all parts . Check that all par ts are included as shown in the illustr ation and

the illustration and parts list.

parts list .

2. Shut off the power at the circuit breaker and remove old f ixtur e

2. Shut off the power at the circuit breaker and remove old fixture from ceiling,

from ceiling, including the old m ounting s trap.

including the old mount ing strap.

3. Thread Nipple(C) into Canopy Loop (F) until snug.

4. Thread other end of the Nipple (C) with Canopy Loop attached into Mounting

4. Thread other end of the Nipple (C) with Canopy Loop attached into Mounting Strap (D).

Strap (D).

5. Place Lock Washer (B) over end of Nipple (C) protruding through Mounting

5. Place Lock Washer (B) over end of Nipple (C) protruding thr ough Mounting Strap (D) and thread Hex Nuts (A) onto Nipple until tight.

Strap (D) and thread Hex Nuts (A) onto Nipple unti l tight.

6. Take this mounting strap assembly and m ount to ceiling juncti on box with

6. Take this mounting strap assem bly and m ount to ceiling junc tion box with junction box Screws (E). Tighten screw securely with screw driver.

7. Unscrew the Canopy l oop collar(H )fr om the Canopy loop. Take the canopy

7. Unscrew the Canopy loop collar (H )from the Canopy loop. T ak e the canopy and pass over the Canopy loop. approx im at ly one half of

and pass over the Canopy loop. approximatly one half of the canopy loop

the canopy loop exterior threads should be ex posed. Adj us t until

exterior threads s hould be exposed. Adjust until desired height is reached. *the

desired height is reached. *the Canopy loop collar should fit snugly on the Canopy loop after the canopy is installed. Remove Canopy

Canopy loop collar should fit snugly on the Canopy loop af ter the canopy is

and Canopy lock collar.

installed. Remove Canopy and C anopy lock collar.

8. Assemble the fixture and have an assistant or secur e support hold

8. Assemble the fixture and have an assistant or secure support hol d the weight

the weight of the fixture while you complete the wiring c onnec tions.

of the fixture while you complete the wiring connections.

9. Thread the fixture wires and ground wire of the assembled fixture

9. Thread the fixture wi res and ground wire of the as sembled fixture through t he

through the canopy loop and nipple and into the outlet box.

CONNECTING THE WIRES (Fig. 2)

10. Attach the power supply wires to the fixture lead wires by connecting BLACK to BLACK (or SMOOTH) and WHITE to WHITE

10. Attach the power supply wires to the f ixture lead wires by connec ting

(or RIBBED).

11. Attach the GROUND wire(GREEN or COPPER) f r om the

11. Attach the GROUND w ire(GREEN or COPPER) f rom the Junction Box and

Junction Box and the fixture Ground wire to the green Gr ound Scr ew on the Mounting Bracket (D) or connect both wires together us ing

the fixture Ground wir e to the green Ground Screw on the Mounting Bracket (D )

the correct size of wire connectors. NOTE: Twist the wires together in the same direction you twist the

or connect both wires together using the correct size of wire connectors .

wire connector onto the wires.

NOTE: Twist the w ires together in the same direction you twist the wire

12. Tuck these wire connections neatly into the J unct ion Box.

connector onto the wires.

13. Raise Canopy (G) to the ceiling and secure in place by tightening

12. Tuck these wi re connections neatl y into the Junction Box.

the Canopy loop collar (H) into the Canopy Loop (F) .

14. Install the light bulbs and shade as per the fixture assembly

Canopy loop collar(H) into the Canopy Loop(F)

sheet.

YOUR INSTALLATION IS NOW COMPLETE.

RETURN POWER TO THE JUNCTION BOX

AND TEST THE FIXTURE.