Page 1
2ea @3/8 x 3mm 3 pcs
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
For Customer Service, contact the place of purchase to arrange for replacement parts.
Company Name:_______________________Co. Account #:_____________
to be filled out by retailer
PARTS & ASSEMBLY SHEET
Read and review installation instruction sheet before
assembling the fixture.
This fixture assembled PO:__________ Date: ________
Decorative Chain
Fig. 1
Bulb
(Not Provided)
M
Fixture Name: Mirabella 7644-M3 GA
Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or
damaged, please note onthis sheet and contact the place of purchase to arrange for replacement parts.
PARTS LIST
Canopy Wire Connectors Top Loop
1ea @5-5/8"X1-5/8" 3ea P4 Orange 1ea @3/8 x 50mm
Chain
1ea 6ft x3.8mm 2ea 8/32" x 1" 1ea @15 x 2mm
Chain Connector Nipple
2ea @3X38mm 1ea @3/8 x 40mm x 5mm 1ea @3/8 x 65mm
Mounting Strap
w/ ground screw
1ea 3/4"X4"
Part Needed Quantity
IXTURE ASSEMBLY INSTRUCTIONS
F
Junction Box
Screw
Canopy Loop
with Collar
Hex Nut
Spring Washer
(CRYSET-7644-M3)
7644-M3 GA
ASSEMBLING THE FIXTURE (Fig. 1)
1. Feed the fixture wires through the Top loop (J) and pull
the wires until taut.
2. Then screw the Top Loop (J) to the threaded center
column of Frame (M) until tight.
3. Gently spread the arms until evenly spaced if arms are
packed closed.
NOTE: INSTALL THE SHADE ASSEMBLY AFTER THE
FIXTURE IS HUNG.
7644-M3 GA PartsInstallation_20120406m(ok)
Page 2
Fixture Name: Mirabella 7644-M3 GA
For Customer Service, contact the place of purchase to arrange for replacement parts.
Fig. 2
PARTS & ASSEMBLY SHEET
C
D
O
b
b
a
a
Bulb
(Not Provided)
M
Nx3pcs
ASSEMBLING THE FIXTURE (Fig. 2)
4. By measuring determine correct number of links needed
4. By measuring determine correct number of links
for proper hanging height. Use a pair of pliers to open one
needed for proper hanging height. Use a pair of pliers
link of the Chain (K) then remove the excess Chain (K) and
to open one link of the Chain (K) then remove the
discard it.
excess Chain (K) and discard it.
5. Use one chain connector (L) to attach one end of
5. Use one chain connector (L) to attach one end of the chain
the chain to the Top loop (J) and close the chain
to the Top loop (J) and close the chain connector.
connector.
6. Feed the fixture wires thr ough the Chain (every
6. Feed the fixture wires through the Chain (every three links)
three links) and pull the wires until taut.
and pull the wires until taut.
7. Slip Canopy loop collar (H) over the chain, then do
7. Slip Canopy loop collar (H) over the chain, then do the
the same with the canopy ( G).
same with the canopy (G).
8. When ready to complete the installation Use the
8. When ready to complete the installation Use the other
other chain connector and attach the other end of
chain connector and attach the other end of the chain to the
the chain to the canopy loop (F) and close the chain
canopy loop (F) and close the chain connector.
connector.
9. Make sure the weight of the chandelier will be supported
9. Make sure the weight of the chandelier will be
by the chain-not the electrical wire.
supported by the chain-not the electrical wire.
* You may now install the fixture.
* You may now install the fixture.
Note: Complete these remaining steps after the
fixture is hung.
Note: Complete these remaining steps after the fixture is
10. Attach hook both ends of the Decorative Chain
(N) to Frame (M) as shown in the diagram.
hung.
11. Pull the straight edges of the hook that sits at
the end of decorative chain (N) outward until it
opens, insert crystal ball (O) into the opening and
then close the hook by pressing the edges together
10. Attach hook both ends of the Decorative Chain (N) to
over the loop at the top of the crystal as shown in
the diagram.
Frame (M) as shown in the diagram.
12. Install the light bulbs (not provided) in
accordance with the fixture's specifications.
(DO NOT EXCEED MAXIMUM WATTAGE RATING)
11. Install the light bulbs (not provided) in accordance with
the fixture's specifications.
Optional:
Carefully clip the Fabric Shade (SHADE-7644) onto
the bulb
(DO NOT EXCEED MAXIMUM WATTAGE RATING)
7644-M3 GA PartsInstallation_20120406m(ok)
Page 3
HANGING THE FIXTURE (Fig.1)
junction box Screws (E). Tighten screw securely with screw driver.
Fig. 1
INSTALLATION INSTRUCTIONS
For Customer Service, contact the place of purchase to arrange for replacement parts.
canopy loop and nipple and into the outlet box.
CONNECTING THE WIRES (Fig 2)
BLACK to BLACK (or SMOOTH) and W H ITE to WHITE (or RIBBED).
Fig. 2
13. Raise Canopy (G) t o the ceiling and secur e in place by tightening the
14. Install the light bulbs and glass shade as per the fixture assembly sheet.
L
B
C
A
JUNCTION BOX
(CEILING)
D
E
F
H
J
CHAIN
G
BARE COPPER
(Ground)
GREEN
(Ground)
FIXTURE WIRES
SMOOTH (BLACK)
RIBBED (WHITE)
BLACK
WHITE
HOUSE WIRES
Fixture Name: Mirabella 7644-M3 GA
For Chandelier Light Fixture
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE (Fig. 1)
1. Carefully remove the new fixture fr om the carton and the yellow
1. Carefully remove the new fixture from the c arton and the yellow bag that
bag that holds all parts. Check that all parts are included as shown in
holds all parts . Check that all parts are included as shown in the illust ration and
the illustration and parts list.
parts list .
2. Shut off the power at the circuit breaker and remove old f ixtur e
2. Shut off the power at the circuit breaker and remove old fixture from ceiling,
from ceiling, including the old m ounting s trap.
including the old mount ing strap.
3. Thread Nipple(C) into Canopy Loop (F) until snug.
3. Thread Nipple(C) into Canopy Loop (F) until s nug.
4. Thread other end of the Nipple (C) with Canopy Loop att ached into Mounting
4. Thread other end of the Nipple (C) with Canopy Loop attached
into Mounting Strap (D).
Strap (D).
5. Place Lock Washer (B) over end of Nipple (C) protruding through Mounting
5. Place Lock Washer (B) over end of Nipple (C) protruding thr ough
Mounting Strap (D) and thread Hex Nuts (A) onto Nipple until tight.
Strap (D) and thread Hex Nuts (A) onto Nipple until tight.
6. Take this mounting strap assembl y and m ount to ceiling junction box with
6. Take this mounting strap assem bly and m ount to ceiling junc tion
box with junction box Screws (E). Tighten screw securely with screw
driver.
7. Unscrew the Canopy l oop collar(H )from the Canopy loop. Take the canopy
7. Unscrew the Canopy loop collar (H )from the Canopy loop. T ak e
the canopy and pass over the Canopy loop. approx im at ly one half of
and pass over the Canopy loop. approximatly one half of the canopy loop
the canopy loop exterior threads should be ex posed. Adj us t until
exterior threads s hould be exposed. Adjust until desired height is reached. *the
desired height is reached. *the Canopy loop collar should fit snugly
on the Canopy loop after the canopy is installed. Remove Canopy
Canopy loop collar should fit snugly on the Canopy loop after the canopy is
and Canopy lock collar.
installed. Remove Canopy and C anopy lock collar.
8. Assemble the fixture and have an assistant or secur e support hold
8. Assemble the fixture and have an assistant or secure support hold the weight
the weight of the fixture while you complete the wiring c onnec tions.
of the fixture while you complete the wiring connections.
9. Thread the fixture wires and ground wire of the assembled fixture
9. Thread the fixture wi res and ground wire of the assembled fixture thr ough the
through the canopy loop and nipple and into the outlet box.
CONNECTING THE WIRES (Fig. 2)
10. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to WHITE
10. Attach the power supply wires to the f ixture lead wires by connecting
(or RIBBED).
11. Attach the GROUND wire(GREEN or COPPER) f r om the
11. Attach the GROUND w ire(GREEN or COPPER) from the Junction Box and
Junction Box and the fixture Ground wire to the green Gr ound Scr ew
on the Mounting Bracket (D) or connect both wires together us ing
the fixture Ground wir e to the green Ground Screw on t he M ounting Bracket (D )
the correct size of wire connectors.
NOTE: Twist the wires together in the same direction you twist the
or connect both wires together using t he correct size of wire connectors.
wire connector onto the wires.
NOTE: Twist the w ires together in t he same direction you twist the wire
12. Tuck these wire connections neatly into the J unct ion Box.
connector onto the wires.
13. Raise Canopy (G) to the ceiling and secure in place by tightening
12. Tuck these wi re connections neatl y into the Junction Box.
the Canopy loop collar (H) into the Canopy Loop (F) .
14. Install the light bulbs and shade as per the fixture assembly
Canopy loop collar(H) into the Canopy Loop(F)
sheet.
YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX
AND TEST THE FIXTURE.
Loading...