Page 1
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
PARTS & ASSEMBLY SHEET
Read and review installation instruction sheet before
assembling the fixture.
to be filled out by retailer
For Customer Service, contact the place of purchase to arrange for replacement parts.
O
P
COU
Fixture Name: Mirabella 7644-M1L GA
This fixture assembled PO:__________ Date: ________
Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or
damaged, please note onthis sheet and contact the place of purchase to arrange for replacement parts.
Company Name:_______________________Co. Account #:_____________
PARTS LIST
Canopy Wire Connectors Top Loop
1ea @5-5/8"X1-5/8" 3ea P4 Orange 1ea @3/8 x 50mm
Chain
1ea 1ft x3.8mm 2ea 8/32" x 1" 1ea @15 x 2mm
Chain Connector Nipple
2ea @3X38mm 1ea @3/8 x 40mm x 5mm 1ea @3/8 x 65mm
Mounting Strap
w/ ground screw
1ea 3/4"X4" 2ea @3/8 x 3mm 3ea @1/2" x 12"
Part Needed Quantity
IXTURE ASSEMBLY INSTRUCTIONS
F
Junction Box
Screw
Canopy Loop
with Collar
Hex Nut Rod
Spring Washer
7644-M1LGA
Fig. 1
ASSEMBLING THE FIXTURE (Fig.1)
1. By measuring determine correct number of rods and
chain needed for proper hanging height. There are 1 ft
of chain and 2 optional 12" rods included.
2. To shorten the fixture slide the excess 12" rods off
the wire.
3. To lengthen the fixture thread the additional rods
These two Rods may
be removed
or
additional Rods may
be added.
ROD-12 GA*
additional chain may
be added.
CHAIN-GA *
*available for purchase
separately
onto the wire or substitute longer chain for the 1 foot
length included.
7644-M1L GA PartsInstallation_20111108m.xls
Page 2
PARTS & ASSEMBLY SHEET
C
D
COUPING
b
b
a
a
Q
N
M
O
P
COUPLER
Fixture Name: Mirabella 7644-M1LGA
ASSEMBLING THE FIXTURE (Fig.2)
4. Pull the fixture’s wire through the Rods until taut.
5. Install the Shade (N) onto the nipple at the top of
Frame (M) and secure with the coupler on Frame (M) until
tight.
6. Thread Rod (O) into Frame (M) until tight.
7. Thread additionsl Rods (O) together using the nipple (P)
between rods until tight. repeat for any additional rods.
8. Feed the fixture wires through the Top loop (J) and pull
the wires until taut. Then screw the Top loop (J) to the rod
on the top of fixture until tight.
9. Use a chain connector (J) to attach one end of the chain
to the Top Loop (L). Close the chain connector. Feed the
fixture wires through the Chain (every three links) and pull
the wires until taut.
10. Slip Canopy loop collar (H) over the chain, then do the
same with the canopy (G).
11. When ready to complete the installation Use the other
chain connector and attach the other end of the chain to
the canopy loop (F) and close the chain connector.
12. Make sure the weight of the chandelier will be
supported by the chain-not the electrical wire.
* You may now install the fixture.
Note: Complete these remaining steps after the fixture is
hung.
13. Install the light bulbs (not provided) in accordance with
the fixture's specifications.
14. Attach hooks at both ends of the Decorative Chain (Q)
to Frame (M) as shown in the diagram.
(CRYSET-7644-M1L 1ea included)
(DO NOT EXCEED MAXIMUM WATTAGE RATING)
Fig. 2
For Customer Service, contact the place of purchase to arrange for replacement parts.
7644-M1L GA PartsInstallation_20111108m.xls
Page 3
For Customer Service, contact the place of purchase to arrange for replacement parts.
BLACK to BLACK (or SMOOTH) and W H ITE to WHITE (or RIBBED).
14. Install the light bulbs and glass shade as per the fi xture assembly sheet.
INSTALLATION INSTRUCTIONS
L
B
C
A
JUNCTION BOX
(CEILING)
D
E
F
H
J
CHAIN
G
BARE COPPER
(Ground)
GREEN
(Ground)
FIXTURE WIRES
SMOOTH (BLACK)
RIBBED (WHITE)
BLACK
WHITE
HOUSE WIRES
Fixture Name: Mirabella 7644-M1L GA
For Chandelier Light Fixture
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE (Fig.1)
HANGING THE FIXTURE (Fig. 1)
1. Carefully remove the new fixture fr om the carton and the yellow
1. Carefully remove the new fixture from the carton and the yellow bag that
bag that holds all parts. Check that all parts are included as shown in
holds all parts . Check that all parts are incl uded as shown in the illustration and
the illustration and parts list.
parts list .
2. Shut off the power at the circuit breaker and remove old f ixtur e
2. Shut off the power at the circuit breaker and remove old f ixture from ceiling,
from ceiling, including the old m ounting s trap.
including the old mount ing strap.
3. Thread Nipple(C) into Canopy Loop (F) until snug.
3. Thread Nipple(C) into Canopy Loop (F) until snug.
4. Thread other end of the Nipple (C) with Canopy Loop attached into Mounting
4. Thread other end of the Nipple (C) with Canopy Loop attached
into Mounting Strap (D).
Strap (D).
5. Place Lock Washer (B) over end of Nipple (C) protruding through Mount ing
5. Place Lock Washer (B) over end of Nipple (C) protruding thr ough
Mounting Strap (D) and thread Hex Nuts (A) onto Nipple until tight.
Strap (D) and thread Hex Nuts (A) onto Nipple until tight.
Fig. 1
6. Take this mounting strap assembly and mount to ceiling junction box with
6. Take this mounting strap assem bly and m ount to ceiling junc tion
box with junction box Screws (E). Tighten screw securely with screw
junction box Screws (E). Tighten scr ew securely with screw driver.
driver.
7. Unscrew the Canopy l oop collar(H )f rom the Canopy loop. Take the canopy
7. Unscrew the Canopy loop collar (H )from the Canopy loop. T ak e
the canopy and pass over the Canopy loop. approx im at ly one half of
and pass over the Canopy loop. approximatly one half of the canopy loop
the canopy loop exterior threads should be ex posed. Adj us t until
exterior threads s hould be exposed. Adjust until desired height is reached. *the
desired height is reached. *the Canopy loop collar should fit snugly
on the Canopy loop after the canopy is installed. Remove Canopy
Canopy loop collar should fit snugly on the Canopy loop after the canopy is
and Canopy lock collar.
installed. Remove Canopy and C anopy lock collar .
8. Assemble the fixture and have an assistant or secur e support hold
8. Assemble the fixture and have an assist ant or secure support hold the weight
the weight of the fixture while you complete the wiring c onnec tions.
of the fixture while you complete the wiri ng connections.
9. Thread the fixture wires and ground wire of the assembled fixture
9. Thread the fixture wi res and ground wire of t he assembled fixture t hrough the
through the canopy loop and nipple and into the outlet box.
canopy loop and nipple and into the outlet box.
CONNECTING THE WIRES (Fig. 2)
CONNECTING THE WIRES (Fig 2)
10. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to WHITE
10. Attach the power supply wires to t he fixture lead wires by connecting
Fig. 2
(or RIBBED).
11. Attach the GROUND wire(GREEN or COPPER) f r om the
11. Attach the GROUND w ire(GREEN or COPPER) from the Junct ion Box and
Junction Box and the fixture Ground wire to the green Gr ound Scr ew
on the Mounting Bracket (D) or connect both wires together us ing
the fixture Ground wir e to the green Ground Screw on the Mounting Bracket (D)
the correct size of wire connectors.
NOTE: Twist the wires together in the same direction you twist the
or connect both wires together usi ng the correct s ize of wire connect ors.
wire connector onto the wires.
NOTE: Twist the w ires together in the same direction you twist the wire
12. Tuck these wire connections neatly into the J unct ion Box.
connector onto the wires.
13. Raise Canopy (G) to the ceiling and secure in place by tightening
12. Tuck these wi re connections neat ly into the Junction Box.
the Canopy loop collar (H) into the Canopy Loop (F) .
13. Raise Canopy (G) t o the ceiling and sec ure in place by tighteni ng the
14. Install the light bulbs and shade as per the fixture assembly
Canopy loop collar(H) into the Canopy Loop(F)
sheet.
YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX
AND TEST THE FIXTURE.
Loading...