Golden Lighting 7644-BA4 GA User Manual
Green
Screw
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
Read and review installation instruction sheet
PARTS & ASSEMBLY SHEET
Company Name:_______________________Co. Account #:____________
below to be filled out by retailer
Fixture Name: Mirabella 7644-BA4 GA
This fixture assembled PO:__________ Date: ________
Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are
missing or damaged, please note onthis sheet and contact the place of purchase to arrange for replacement
parts.
PARTS LIST
Mounting
Strap
1ea 4"X3" 2ea 8/32"X1" 2ea 8/32"X28mm
Wire
Connnector
3ea P4 Orange 2ea 8/32"X3.5mm 2ea 9X9.5mm
Ground
1ea 8/32"X10mm 3pcs
Part Needed Quantity
Part Needed Quantity
IXTURE ASSEMBLY INSTRUCTIONS
F
before assembling the fixture.
Junction Box
Screw
Hex Nut
Decorative Chain
(CRYSET-7644-BA4)
Mounting
Screw
Deco Nut
(round nut)
7644-BA4 GA
1. Locate the Decorative Chain (P) and attach hook
both ends of the Decorative Chain (P) to fixture body
as shown in the diagram.
2. Slide the Glass Shade (H) and Collar (N) over
Socket (I) and secure Glass Shade (H) by threading
the Socket Ring (J) to Socket (I)
3. Install the light bulb in accordance with the fixture's
specifications.
Fig. 4
NOTE: INSTALL THE GLASS ASSEMBLY
AFTER THE FIXTURE IS HUNG.
For Customer Service, contact the place of purchase to arrange for replacement parts.
7644-BA4 GA PartsInstallation_20120503m.xls
11. Install glass as per the fixture assembly instructions
INSTALLATION INSTRUCTIONS
JUNCTION BOX
E
A
G
F
D
B
C
BARE COPPER
(Ground)
GREEN
(Ground)
FIXTURE WIRES
SMOOTH (BLACK)
RIBBED (WHITE)
BLACK
WHITE
HOUSE WIRES
Fixture Name: Mirabella 7644-BA4 GA
For Wall Mount Light Fixture
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE (Fig. 1)
1. Carefully remove the new fixture from the carton and the
yellow bag that holes all your parts. Check that all parts are
included as shown in the illustration and parts list.
2. Shut off power at the circuit breaker and remove the old
fixture from wall, including the old mounting strap.
3. The Mounting Strap(A) contains several pairs of threaded
holes, find the pair of holes that match the holes spacing in your
fixture Back Plate (K) and thread the two Mounting Screws(B)
half way into the Mounting Strap(A).
4. Place the Mounting Strap (A) over the Junction Box (E) so the
Mounting Screws (B) are vertical or horizontal, as required by
fixture type.
5. Attach the Mounting Strap (A) to the Junction Box (E) by
using the two mounting screws(D). Tighten the screws securly.
CONNECTING THE WIRES (Fig. 2)
6. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to
WHITE (or RIBBED).
7. Attach the GROUND wire(GREEN or COPPER) from the
Junction Box and the fixture Ground wire to the green Ground
Screw on the Mounting Bracket (A) or connect both wires
together using the correct size of wire connectors.
NOTE:Twist the wires together in the same direction you twist
the wire connector onto the wires.
8. Tuck these wire connections neatly into the Junction Box.
Fig. 1
Fig. 2
FINISHING THE INSTALLATION (Fig. 3)
9. Place the fixture Back Plate (K), over the Mounting
screws(B), so they protrude through the holes in the Back Plate
(K).
10. Thread the Deco Nuts (L) onto the Mounting Screws (B) and
continue turning until the Back Plate (K) is snug against the wall.
YOUR INSTALLATION IS NOW COMPLETE. RETURN
POWER TO THE JUNCTION BOX AND TEST THE FIXTURE.
For Customer Service, contact the place of purchase to arrange for replacement parts.
Fig. 3
Loading...