2ea @3/8 x 3mm 9 pcs O + N
Reason why ( missing, scratched, broken glass, bent, bad finish)
Company Name:_______________________Co. Account #:_____________
to be filled out by retailer
PARTS & ASSEMBLY SHEET
Read and review installation instruction sheet before
assembling the fixture.
This fixture assembled PO:__________ Date: ________
For Customer Service, contact the place of purchase to arrange for replacement parts.
Fixture Name: Mirabella 7644-9 GA
Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or
damaged, please note onthis sheet and contact the place of purchase to arrange for replacement parts.
Canopy Wire Connectors Top Loop
1ea @5-5/8"X1-5/8" 3ea P4 Orange 1ea @3/8 x 50mm
Chain
1ea 6ft x3.8mm 2ea 8/32" x 1" 1ea @15 x 2mm
Chain Connector Nipple
2ea @3X38mm 1ea @3/8 x 40mm x 5mm 1ea @3/8 x 65mm
Mounting Strap w/
ground screw
1ea 3/4"X4"
Part Needed Quantity
Junction Box
Screw
Canopy Loop
with Collar
Hex Nut
Spring Washer
(CRYSET-7644-9)
FIXTURE ASSEMBLY INSTRUCTIONS
7644-9 GA
ASSEMBLING THE FIXTURE (Fig. 1)
1. Feed the fixture wires through the Top loop (J) and pull the
wires until taut.
2. Then screw the Top Loop (J) to the threaded center
column of Frame (M) until tight.
3. Gently spread the arms until evenly spaced if arms are
packed closed.
NOTE: INSTALL THE SHADE ASSEMBLY AFTER THE
FIXTURE IS HUNG.
7644-9 GA PartsInstallation_20120406m(ok)
For Customer Service, contact the place of purchase to arrange for replacement parts.
P
(Not Provided)
Bulb
M
a
b
a
b
c
d
c
d
Nx6pcs
Ox3pcs
Fixture Name: Mirabella 7644-9 GA
ASSEMBLING THE FIXTURE (Fig. 2)
4. By measuring determine correct number of links
needed for proper hanging height. Use a pair of pliers
to open one link of the Chain (K) then remove the
excess Chain (K) and discard it.
5. Use one chain connector (L) to attach one end of
the chain to the Top loop (J) and close the chain
connector.
6. Feed the fixture wires thr ough the Chain (every
three links) and pull the wires until taut.
7. Slip Canopy loop collar (H) over the chain, then do
the same with the canopy ( G).
8. When ready to complete the installation Use the
other chain connector and attach the other end of
the chain to the canopy loop (F) and close the chain
connector.
9. Make sure the weight of the chandelier will be
supported by the chain-not the electrical wire.
* You may now install the fixture.
Note: Complete these remaining steps after the
fixture is hung.
10. Attach hook both ends of the Decorative Chain
(N) and (O) to Frame (M) as shown in the diagram.
11. Pull the straight edges of the hook that sits at
the end of decorative chain (N) outward until it
opens, insert crystal ball (P) into the opening and
then close the hook by pressing the edges together
over the loop at the top of the crystal as shown in
the diagram.
12. Install the light bulbs (not provided) in
accordance with the fixture's specifications.
(DO NOT EXCEED MAXIMUM WATTAGE RATING)
Optional:
Carefully clip the Fabric Shade (SHADE-7644) onto
the bulb
Pearl Chiffon Shades -3 pack available separately
7644-9 GA PartsInstallation_20120406m(ok)