Golden Lighting 7644-1W GA User Manual

Fig. 1
Fig. 2

JUNCTION BOX

E

A

G

F

D

B

C

BARE COPPER

(Ground)

GREEN
(Ground)

FIXTURE WIRES

SMOOTH (BLACK)

RIBBED (WHITE)

BLACK

WHITE

HOUSE WIRES

HANGING THE FIXTURE (Fig. 1)

1. Carefully remove the new fixtur e from the carton and the
yellow bag that holes all your parts. Check that all parts are
included as shown in the illustration and parts list.

2. Shut off power at the circuit br eaker and remove the old
fixture from wall, including the old mounting strap.

3. The Mounting Strap(A) contains several pairs of threaded
holes, find the pair of holes that match the holes spacing in
your fixture Back Plate (K) and thread the two Mounting
Screws(B) half way into the Mounting Strap(A).

4. Place the Mounting Strap ( A) over the Junction Box (E) so
the Mounting Screws (B) are vertical or horizontal, as
required by fixture type.

5. Attach the Mounting Strap (A) to the Junction Box (E) by
using the two mounting screws(D). Tighten the screws
securly.

CONNECTING THE WIRES (Fig. 2)

6. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to
WHITE (or RIBBED).

7. Attach the GROUND wire(GREEN or COPPER) from the
Junction Box and the fixture Ground wire to the green
Ground Screw on the Mounting Bracket (A) or connect both
wires together using t he cor r ect size of wire connectors.
NOTE: Twist the wires together in the same direction you
twist the wire connector ont o t he wires.

8. Tuck these wire connections neatly into the Junction Box.

FINISHING THE INSTALLATION (Fig. 3)

9. Place the fixture Back Plate (J), over the Mounting
screws(B), so they protrude through the holes in the Back
Plate (J).

10. Thread the Deco Nuts (H) onto the Mounting Screws (B)
and continue turning until the Back Plate (J) is snug against
the wall.

11. Install shade as per the fixture assembly instructions

YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX AND TEST
THE FIXTURE.

INSTALLATION INSTRUCTIONS

Fixture Name: Mirabella 7644-1W GA

For Wall Mount Light Fixture

WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.

Fig. 3

For Customer Service, contact the place of purchase to arrange for replacement parts.

Reason why ( missing, scratched, broken glass, bent, bad finish)

Comments

Read and review installation instruction sheet before

PARTS & ASSEMBLY SHEET

Company Name:_______________________Co. Account #:_____________

below to be filled out by reta iler

Fixture Name: Mirabella 7644-1W GA

This fixture assembled PO:__________ Date: ________

Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or

damaged, please note onthis sheet and contact the place of purchase to arrange for replacement parts.

PARTS LIST

Mounting Strap

1ea 4"X3" 2ea 8/32"X1" 2ea 8/32"X28mm

Wire Connnector Hex Nut

3ea P4 Orange 2ea 8/32"X3.5mm 2ea 9X9.5mm

Green Ground
Screw

1ea 8/32"X10mm 1 ea

Part Needed Quantity
Part Needed Quantity

Junction Box
Screw

Decorative Chain
(CRYSET-7644-M1L)

Mounting Screw

Deco Nut (round
nut)

FIXTURE ASSEMBLY INSTRUCTIONS

assembling the fixture.

Fig. 4

7644-1W GA

1. Locate the decorative chain (L) and attach hooks at
both ends of the decorative chain (L) to fixture body as
shown in the diagram.

2. Install the light bulb in accordance with the fixture's
specifications.

3. Carefully clip the Fabric Shade ( K )
(1 pc of SHADE-7644 included) onto the bulb.

(DO NOT EXCEED THE MAXIMUM WATTAGE RATING!)

For Customer Service, contact the p lace of p urchase to arrange for replacement parts.

7644-1W GA PartsInstallation_20111108m.xls