Golden Lighting 7509-M1L PW User Manual

3ea ∅11.7*H12"

1ea ∅11.7*H6"

Part Needed Quantity

Reason why ( missing, scratched, broken glass, bent, bad finish)

Comments

For Customer Service, contact the place of purchase to arrange for replacement parts.

PARTS LIST

Fig 1

Read and review installation instruction sheet before assembling the

5. Install the light bulb in accordance with the fixture's specification.

PARTS & ASSEMBLY SHEET

Notice:

Company Name:_______________________Co. Account #:_____________

to be filled out by retailer

Fixture Name: Asteria 7509-M1L PW

This fixture assembled PO:__________ Date: ________

Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or

damaged, please note onthis sheet and contact the place of purchase to arrange f or replacement parts.

Canopy Mounting screws Mounting strap

1ea ∅5-1/2"*H1" 2ea 8#32-IP*1"

Wire connectors Mounting screws Hex sut

3ea P3 Orange 2ea 5/32-IP*1-3/5" 2ea 5/32-IP*H3mm

Rod Bulb

1ea G9*40W

Part Needed Quantity

FIXTURE ASSEMBLY INSTRUCTIONS

fixture.

1. By measuring, determine the correct number of rods needed for proper

hanging height.

* This fixture includes 4 rods (6", 12", 12", 12")

2. To shorten the fixture; slide the excess rods off the wires. To lengthen

add additional rods. The 12" rods are optional.

3. Pull the fixture’s wires through Rods (G) until taut and thread the rods

together. Then thread rods to the Fixture Coupler (H) at top of fixture and the

1ea ∅4"*H2mm

Deco sut

2ea 5/32-IP*H10mm

7509-M1L PW

swivel joint on Canopy (F)

4.Pour Crystals (Y) into the groove of Glass Shades (O) then place Glass

Shades (O) over the threaded Sockets (P),secure Glass Shades (O) by

threading on

Socket Rings (N) until tight.

Bulb note: Use a tissue or paper towel to hold the bulb and push down into

the socket. Oils or dirt can cause the bulb life to shorten. Rubbing alcohol is

recommended to clean the bulbs if dirty.

(DO NOT EXCEED THE MAXIMUM WATTAGE RATING!)

NOTE: INSTALL THE GLASS ASSEMBLY AFTER THE FIXTURE IS HUNG.

Fig. 3

Fig. 1

Fig. 2

BARE COPPER

(Ground)

GREEN
(Ground)

FIXTURE WIRES

SMOOTH (BLACK)

RIBBED (WHITE)

BLACK

WHITE

HOUSE WIRES

HANGING THE FIXTURE (Fig. 1)

1. Carefully remove the new fixture from the carton and
the yellow bag that holds all y our parts. Check that all
parts are included as shown in t he illustrat ion and parts
list.

2. Shut off power at the circuit breaker and remove the old
fixture from wall, including the old mounting strap.

3. Mounting Strap (A) contains s everal pairs of threaded
holes, find the pair of holes that matches the holes
spacing in your fixture Canopy (G) and thread Mounting
Screws (B) into the Mounting Str ap (A). Secure with Hex
nuts (C). These will have their thr eaded ends protrude
through the two holes in the fixture canopy.

4. Place Mounting Strap (A) over the Junction Box (E) so
the Mounting Screws (B) are vertical or horizontal, as
required by fixture type.

5. Attach Mounting Strap (A) t o Junct ion Box (E) by using
the two Mounting Screws (B). Tighten the screws
securely.

CONNECTING THE WIRES (Fig. 2)

5. Attach the power supply w ires t o t he fixtur e lead wires
by connecting BLACK to BLACK (or SMOOTH) and
WHITE to WHITE (or RIBBED).

6. Attach the GROUND wire (GREEN or COPPER) from
the junction box and the fixture G r ound wire to the green
Ground Screw on the Mounting Bracket (A) or connect
both wires together using the correct size of wire
connectors.
NOTE: Twist the wires together in the same direction you
twist the wire connector onto t he w ir es.

7. Tuck these wire connections neat ly into the junction
box.

FINISHING THE INSTALLATION (Fig. 3)

9. Place Canopy (G), over Mounting screws (B), so they
protrude through the holes in Canopy (G).

10. Thread Deco Nuts (F) onto Mount ing Screws (B) and
continue turning until Canopy (G) is snug against the
ceiling.

11. Install glass shades as per the fixture assembly
instructions.

YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX AND TEST
THE FIXTURE.

INSTALLATION INSTRUCTIONS

Fixture Name: Asteria 7509-M1L PW

For Pendant Light Fixture

WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.

For Customer Service, contact the place of purchase to arrange for replacemen t parts.