Golden Lighting 7509-BA2 PW User Manual

below to be filled out by retailer

Read and review installation ins t ruction sheet
before assemblin g the fixture.

PARTS LIST

3. Install the provided light bulb in accordance with the fixture's

clean the bulbs if dirty.

PARTS & ASSEMBLY SHEET

This fixture assembled PO:__________ Date: ________

Notice:

Company Name:_______________________Co. Account #:___________

Fixture Name: Asteria 7509-BA2 PW

Please review the parts listing and check for all parts before assembling the fixture. If any parts are
missing or damaged, please note onthis shee t and contact the place of purchase to arrange for replacement
parts.

Mounting St rap

1ea 4"X3" 2ea 8/32"X1" 2ea 8/32"X28mm

Wire
Connnector

3ea P3 Orange 2ea 8/32"X3.5mm 2ea 9X9.5mm

Green Ground
Screw

1ea 8/32"X10mm

Part Needed Quantity
Part Needed Quantity

Reason why ( missing , scra t c hed, broken glass, bent, bad finish)
Comments

F

IXTURE ASSEMBLY INSTRUCTIONS

Junction Box
Screw

Hex Nut

Bulb

2ea G9*40W

Mounting Sc re w

Deco Nut
(round nut)

7509-BA2 PW

1.Pour Crystals (Y) into the groove of Glass Shade (O). Then,
gently slide Glass Shade (O) over the socket and secure Glass
Shade (O) by threading Socket Ring (L) over the socket.

Fig. 1

2. Thread the Final Cap (R) into Bath Bar (S) unitl tighted.

specifications. Bulb note: Use a tissue or paper towel to hold
the bulb and push down into the socket. Oils or dirt can cause
the bulb life to shorten. Rubbing alcohol is recommended to

(DO NOT EXCEED THE MAXIMUM WATTAGE RATING!)

NOTE: INSTALL THE GLASS ASSEMBLY

AFTER THE FIXTURE IS HUNG.

For Customer Service, contact the place of purchase to arrange for replacement parts.

FINISHING THE INSTALLATION (Fig. 3)

Fig. 3

HANGING THE FIXTURE (Fig. 1)

Fig. 1

CONNECTING THE WIRES (Fig. 2)

Fig. 2

INSTALLATION INSTRUCTIONS

BARE COPPER

(Ground)

GREEN
(Ground)

FIXTURE WIRES

SMOOTH (BLACK)

RIBBED (WHITE)

BLACK

WHITE

HOUSE WIRES

Fixture Name: Asteria 7509-BA2 PW

WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.

1. Carefully remove the new fixture from the carton and the yellow
bag that holds all your parts. Check that all parts are included as
shown in the illustration and parts list.

2. Shut off power at the circuit breaker and remove the old fixture
from wall, including the old mounting strap.

3. Mounting Strap (A) contains several pairs of threaded holes. Find
the pair of holes that matches the holes spacing in fixture Back Plate
(K) and thread the Mounting Screws (B) half way into Mounting Strap
(A).

4. Place Mounting Strap (A) over Junction Box (E) so that Mounting
Screws (B) are vertical or horizontal, as required by fixture type.

5. Attach Mounting Strap (A) to Junction Box (E) by using two
mounting screws (D). Tighten the screws securely.

For Wall Mount Light Fixture

5. Attach the power supply wires to the fixture lead wires by

connecting BLACK to BLACK (or SMOOTH) and WHITE to WHITE

(or RIBBED).

6. Attach the GROUND wire (GREEN or COPPER) from the Junction

Box and the fixture Ground wire to the green Ground Screw on

Mounting Bracket (A) or connect both wires together using the

correct size of wire connectors.

NOTE: Twist the wires together in the same direction you twist the

wire connector onto the wires.

7. Tuck these wire connections neatly into the Junction Box.

9. Place fixture Back Plate (J), over Mounting Screws (B), so they

protrude through the holes in Back Plate (J).

10. Thread Deco Nuts (H) onto Mounting Screws (B) and continue

turning until Back Plate (J) is snug against the wall.

11. Install glass as per the fixture assembly instructions

YOUR INSTALLATION IS NOW COMPLETE. RETURN POWER TO

THE JUNCTION BOX AND TEST THE FIXTURE.

For Customer Service, contact the place of purchase to arrange for replacement parts.