Page 1
1ea 3"X4"
2ea 8/32"X28mm
2ea 8/32X1"
PARTS & ASSEMBLY SHEET
This fixture assembled PO:__________ Date: ________
Rubbing alcohol is recomm ended to clean the bulbs if
(DO NOT EXCEED THE MAXIMUM WATTAGE RATING!)
NOTE: I
Company Name:_______________________Co. Account #:_____________
below to be filled out by retailer
Read and review installation instruction sheet before
Fixture Name: Asteria 7509-BA1 PW
Notice: Please review the parts listing and check for all parts before assembl ing the fixture. If any parts are missing or
damaged, please note onthis sheet and contact the place of purchase to arrange for replacement parts.
PARTS LIST
Mounting strap Mounting Screw Mounting screw
Wire connnector Hex Nut
3ea P3 Orange
Green Ground
screw
1ea 8/32"X10mm 1ea G9*40W
Part Needed Quantity
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
2ea 8/32"X3.5mm
Bulb
Deco nut
nut)
2ea 9X9.5mm
(round
FIXTURE ASSEMBLY INSTRUCTIONS
assembling the fixture.
7509-BA1 PW
Fig. 4
1.Pour Crystal s (Y) into the groove of Glass Shade
(O). Then, gently slide Glass Shade (O) over the
socket and secure Glass Shade (O) by threading
Socket Ring (L) over the socket.
2. Install the provided light bulb in accordance with
the fixture's specifi cations. Bulb note: Use a tissue or
paper towel to hold the bulb and push down i nto the
socket. Oils or dirt can cause the bulb life to shorten.
dirty.
NSTALL THE GLASS ASSEMBLY AFTER
THE FIXTURE IS HUNG.
For Customer Service, contac t the place of purchase to arrange for replacement parts.
Page 2
HANGING THE FIXTURE (Fig. 1)
Fig. 1
CONNECTING THE WIRES (Fig. 2)
Fig. 2
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
FINISHING THE INSTALLATION (Fig.3)
) onto the Mounting
Screws (B) and continue turning until the Back
instructions
Fig. 3
BARE COPPER
(Ground)
GREEN
(Ground)
FIXTURE WIRES
SMOOTH (BLACK)
RIBBED (WHITE)
BLACK
WHITE
HOUSE WIRES
HANGING THE FIXTURE (Fig. 1)
1. Carefully remove the new fixture from the carton and the
1. Carefully remove the new fixture from the
yellow bag that holds all your parts. Check that all parts are
carton and the yellow bag that holes all your
included as shown in the illustration and parts list.
parts. Check that all parts are included as
shown in the illustration and parts list.
2. Shut off power at the circuit breaker and remove the old
2. Shut off power at the circuit breaker and
fixture from wall, including the old mounting strap.
remove the old fixture from wall, including
3. Mounting Strap (A) contains several pairs of threaded
the old mounting strap.
holes. Find the pair of holes that matches the holes spacing
3. The Mounting Strap(A) contains several
in fixture Back Plate (K) and thread the Mounting Screws (B)
pairs of threaded holes, find the pair of
half way into Mounting Strap (A).
holes that match the holes spacing in your
4. Place Mounting Strap (A) over Junction Box (E) so that
fixture Back Plate (K) and thread the two
Mounting Screws (B) are v er t ical or horizontal, as required
Mounting Screws(B) half way into the Mounting
by fixture type.
Strap(A).
5. Attach Mounting Strap (A) t o Junc t ion Box (E) by using
two mounting screws (D). Tighten the screws securely.
5. Attach the power supply wires to the
CONNECTING THE WIRES (Fig. 2)
fixture lead wires by connecting BLACK to
5. Attach the power supply wires to the fixture lead wires by
BLACK (or SMOOTH) and WHITE to WHITE (or
connecting BLACK to BLACK (or SMOOTH) and WHITE to
RIBBED).
WHITE (or RIBBED).
6. Attach the GROUND wire(GREEN or COPPER)
6. Attach the GROUND wire (GREEN or COPPER) from the
from the Junction Box and the fixture Ground
Junction Box and the fixture Ground wire to the green
wire to the green Ground Screw on the
Ground Screw on Mounting Bracket (A) or connect both
Mounting Bracket (A) or connect both wires
wires together using the correct size of wire connectors.
together using the correct size of wire
NOTE: Twist the wires together in the same direction you
twist the wire connector onto the wires.
connectors.
NOTE:Twist the wires together in the same
7. Tuck these wire connections neat ly into the Junction Box.
direction you twist the wire connector onto
the wires.
FINISHING THE INSTALLATION (Fig. 3)
9. Place fixture Back Plate (J), over Mounting Screws (B), so
they protrude through the holes in Back Plate (J).
9. Place the fixture Back Plate (J), over the
10. Thread Deco Nuts (H) onto Mounting Screws (B) and
Mounting screws(B), so they protrude through
continue turning until Back Plate (J) is snug against the wall.
the holes in the Back Plate (J).
10. Thread the Deco Nuts (H
11. Install glass as per the fixture as sembly instructions
YOUR INSTALLATION IS NOW COMPLETE . RE TURN
POWER TO THE JUNCTION BOX AND TEST THE
Plate (J) is snug against the wall.
FIXTURE.
11. Install glass as per the fixture assembly
INSTALLATION INSTRUCTIONS
Fixture Name: Asteria 7509-BA1 PW
For Wall Mount Light Fixture
YOUR INSTALLATION IS NOW COMPLETE. RETURN
POWER TO THE JUNCTION BOX AND TEST THE
FIXTURE.
For Customer Service, contact the place of purchase to arrange for replacement parts.
Loading...