Golden Lighting 7509-5 PW User Manual

Page 1
Fig 1
Read and review installation instruction sheet
ASSEMBLING THE FIXTURE (Fig.1)
NOTE: INSTALL THE GLASS ASSEMBLY
AFTER THE FIXTURE IS HUNG.
to be filled out by retailer
PARTS & ASSEMBLY SHEET
This fixture assembled PO:__________ Date: ________
Notice:
parts.
Company Name:_______________________Co. Account #:_____________
Fixture Name: Asteria 7509-5 PW
missing or damaged, please note onthis sheet and contact the place of purchase to arrange for replacement
Please review the parts listing and check for all parts before assembling the fixture. If any parts are
PARTS LIST
Canopy Mounting S crews Top loop
1ea 5-1/2"*H1" 2ea 8#32-IP*1" 1ea 50MM*H60mm
Chain Wire connectors Nipple
1ea 6ft 3.8 3ea P3 Orange 1ea 1/4-IP*H60mm
Chain connector
2ea ∅5.8*H61mm 1ea ∅1-1/8"*H42mm 1ea W4-1/8"*E1"*H5mm
Hex Nut
1ea 1/8-IP*H4mm
Part Needed Quantity Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish) Comments
Canopy loop with Collar
Bulb
5ea G9*40W
Mounting strap
FIXTURE ASSEMBLY INSTRUCTIONS
before assembling the fixture.
1. Gently spread the arms until evenly spaced if arms are packed closed.
For Customer Service, contact the place of purchase to arrange for replacement parts.
7509-5 PW
Page 2
For Customer Service, contact the place of purchase to arrange for replacement parts.
ASSEMBLING THE FIXTURE (Fig.2)
2. Feed the fixture wires through Top Loop (J) and pull
to open one link of Chain (C2) then remove the excess
Note: Complete these remaining steps after the fixture
(DO NOT EXCEED MAXIMUM WATTAGE RATING)
PARTS & ASSEMBLY SHEET
Fig 2
Fig 3
Fig 4
Fixture Name: Asteria 7509-5 PW
the wires until taut.
3. Then screw Top Loop (J) to the threaded center column of Frame (M) until tight.
4. By measuring, determine correct number of links needed for proper hanging height. Use a pair of pliers
Chain (C2) and discard it.
5. Use one Chain Connector (E2) to attach one end of the chain to the Top Loop (D2) and close the chain connector.
6. Feed the fixture wires through the Chain (every three links) and pull the wires until taut.
7. Slip Canopy Loop Collar (B2) over the chain, then do the same with the canopy (F2).
8. When ready to complete the installation Use the other chain connector and attach the other end of the chain to the Canopy Loop (A2) and close the chain connector.
9. Make sure the weight of the chandelier will be supported by the chain-not the electrical wire. * You may now install the fixture.
is hung.
10. Pour crystals (Y) into the groove of Glass Shade (O) then place Glass Shades (O) over threaded Sockets (P). Secure Glass Shades (O) by threading Socket Rings (N) until tight.
11. Install the light bulbs in accordance with the fixture's specifications. Bulb note: Use a tissue or paper towel to hold the bulb and push down into the socket. Oils or dirt can cause the bulb life to shorten. Rubbing alcohol is recommended to clean the bulbs if dirty.
Page 3
13. Raise Canopy (G) to the ceiling and secure in place by
assembly sheet.
RETURN POWER TO THE JUNCTION BOX AND
HANGING THE FIXTURE (Fig.1)
1. Carefully remove the new fixture from the cart on and the yellow
securely with screw driver.
Fig. 1
7. Unscrew the Canopy Loop Collar (H) from the canopy loop.
CONNECTING THE WIRES (Fig 2)
the wire connector onto the wires.
Fig. 2
INSTALLATION INSTRUCTIONS
Fixture Name: Asteria 7509-M3/5/9 PW
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
bag that holds all parts. Check that all parts are included as shown in the illustration and parts list.
2. Shut off the power at the circuit breaker and r emove old fixtur e from ceiling, including the old mounting strap.
3. Thread Nipple (C) into Canopy Loop (F) until snug.
4. Thread other end of the Nipple (C) with Canopy Loop (F) attached into Mounting Strap (D).
5. Place Lock Washer (B) over end of Nipple (C) protruding through Mounting Strap (D) and thread Hex Nuts (A) ont o Nipple until tight.
6. Take this mounting strap assembly and mount to ceiling junction box with Junction Box Screws (E). Tighten screw
For Chandelier Light Fixture
Take the canopy and pass over the canopy loop. Approximately one half of the canopy loop exterior threads should be exposed. Adjust until desired height is reached. *the canopy loop collar should fit snugly on the canopy loop after the canopy is installed. Remove the canopy and canopy lock collar.
8. Assemble the fixture and have an assistant or secure support hold the weight of the fixture while you complete the wiring connections.
9.Thread the fixture wires and ground wire of the assembled fixture through the canopy loop and nipple and into the outlet box.
10. Attach the power supply wires to the fixture lead wires by connecting BLACK to BLACK (or SMOOTH) and WHITE to WHITE (or RIBBED).
11. Attach the GROUND wire (GREEN or COPPER) from the Junction Box and the fixture Ground w ire to the green Ground Screw on the Mounting Bracket (D) or connect both wires together using the correct size of wire connectors. NOTE: Twist the wires together in the same direction you tw ist
12. Tuck these wire connections neatly int o t he junction box.
tightening the Canopy Loop Collar (H) into the Canopy Loop (F)
14. Install the light bulbs and glass shade as per the fixture
For Customer Service, contact the place of purchase to arrange for replacement parts.
YOUR INSTALLATION IS NOW COMPLETE.
TEST THE FIXTURE.
Loading...