Page 1
PARTS & ASSEMBLY SHEET
2. Install the bottom assembly and Glass shade beginning at step X
Fixture Name: Mayfair 7116-SF LC
This fixture assembled PO:__________ Date: ________
Notice:
damaged, please note onthis sheet and contact the place of purchase to arrange for replacement parts.
PARTS LIST
Canopy Mounting Screws Top loop
1ea ∅6-1/2"*H1-1/2" 2ea 8#32-IP*1" 1ea 1/8-IP*H60mm
Chain Wire connectors Nipple
1ea 6ft ∅3.8 3ea P3 Orange 1ea 1/4-IP*H60mm
Chain connector
2ea ∅5.8*H61mm 1ea ∅1-1/8"*H42mm 1ea W4-1/8"*E1"*H5mm
Nipple
1ea 1/8-IP*H120mm 2ea 1-1/2-IP*H2mm
Bottom cap
1ea ∅3-1/4"*H25mm 1ea 1/8-IP*H4mm
Part Needed Quantity
Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or
Company Name:_______________________Co. Account #:_____________
to be filled out by retailer
Canopy loop
with Collar
Metal washer &
Plastic washer
Hex Nut Finial
Mounting strap
Deco Screw
6ea 5/32-IP*H9mm
1ea 1/8-27-IP*H39mm
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
F
IXTURE ASSEMBLY INSTRUCTIONS
Read and review installation instruction sheet before
assembling the fixture.
ASSEMBLING THE FIXTURE as Semi flush (Fig 1)
NOTE: Assemble on a cushioned surface to prevent damage to
glass finish.
1. Gently spread the arms until evenly spaced if arms are packed
closed. Thread the Deco screw (A1) and （A3）into the lower hole
(A4) and upper hole (A5) of Scroll arms until tight.
in of (Fig 2) after fixture is hung.
Fig 1
7116-SF LC
For Customer Service, contact the place of purchase to arrange for replacement parts.
7116-PartsInstallation_20110106m.xls
Page 2
PARTS & ASSEMBLY SHEET
hold the Deco nuts (E) in place on the fixture Top cap (M).
4. By measuring determine correct number of links needed
the canopy loop (A2) and close the chain connector. Make
washer (O), plastic washer (P), glass shade (S) thread the
washer (X), metal washer (Y), hex nut (T) ,bottom cap (V)
Fixture Name: Mayfair 7116-SF LC
ASSEMBLING THE FIXTURE as Chain hung (Fig 2)
1. Remove the Circular strap from top of Fixture and
replace the long mounting screws with two short screws to
2. Feed the fixture wires through the Top loop (J) and pull
the wires until taut. Then screw the Top Loop (J) to the
tcoupler (M) in top cap until tight.
3. Gently spread the arms until evenly spaced if arms are
packed closed. Thread the Deco screw (A1) and
（A3）
Scroll arms until tight.
for proper hanging height. Use a pair of pliers to open one
link of the Chain (C2) then remove the excess Chain (C2)
and discard it.
5. Use one chain connector (E2) to attach one end of the
chain to the Top loop (J) and close the chain connector.
6. Feed the fixture wires through the Chain (every three
links) and pull the wires until taut.
into the lower hole (A4) and upper hole (A5) of
Fig 2
E
7. Slip Canopy loop collar (B2) over the chain, then do the
same with the canopy (F2).
8. When ready to complete the installation Use the other
chain connector and attach the other end of the chain to
sure the weight of the chandelier is supported by the chainnot the electrical wire.
* You may now install the fixture.
Note: Complete these remaining steps after the fixture is
hung.
9. Thread the threaded rod/nipple (N) onto the socket
assembly coupler, secure with a hex nut.
10. Install the light bulbs in accordance with the fixture's
specifications.
11. Thread on the Nipple (N) in this order:hex nut, metal
nipple through the hole in bottom of glass shade, plastic
and secure in place with the Finial (Z).
(DO NOT EXCEED MAXIMUM WATTAGE RATING)
For Customer Service, contact the place of purchase to arrange for replacement parts.
7116-PartsInstallation_20110106m.xls
Page 3
INSTALLATION INSTRUCTIONS
yellow bag that holds all your parts. Check that all parts are
Fixture Name:
Mayfair 7116-SF LC
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE as Semi flush (Fig. 1)
1. Carefully remove the new fixture from the carton and the
included as shown in the illustration and parts list.
2. Shut off power at the circuit breaker and remove the old
fixture from ceiling, including the old mounting strap.
3. The Circular Strap ( A ) contains several pairs of
threaded holes, find the pair of holes that match the hole
spacing in your fixture Back Plate (D) and thread the two
Mounting Screws (C) half way into the Mounting Strap (A)
facing down, Secure in place with hex nuts. These will
have their threaded ends protrude through the two holes in
the fixture canopy (D).
4. Place the Mounting Strap ( A ) over the junction
5. Attach the Mounting Strap (A) to the Junction Box using
the two mounting screws (B). Tighten the screws (B)
securely with screw driver.
For Semi Flush / Convertible Light Fixture
Fig. 1
CONNECTING THE WIRES (Fig. 2)
6. Attach the power supply wires to the fixture lead wires
by connecting BLACK to BLACK (or SMOOTH) and
WHITE to WHITE (or RIBBED).
7. Attach the GROUND wire(GREEN or COPPER) from
the Junction Box and the fixture Ground wire to the green
Ground Screw on the Mounting Strap (A) or connect both
wires together using the correct size of wire connectors.
NOTE: Twist the wires together in the same direction you
twist the wire connector onto the wires.
8. Tuck these wire connections neatly into the Junction
Box.
FINISHING THE INSALLATION (Fig. 3)
9. Place the fixture’s canopy over the Mounting strap (A),
adjust the canopy (D) until the Mounting Screws (C)
protrude out from the canopy (D) and secure by threading
the Decorative nuts (E) on until tight.
10. Install the light bulbs and glass shade as per the fixture
assembly sheet.
YOUR INSTALLATION IS NOW COMPLETE. RETURN
POWER TO THE JUNCTION BOX AND TEST THE
FIXTURE.
Fig 2
Fig. 3
For Customer Service, contact the place of purchase to arrange for replacement parts.
Page 4
INSTALLATION INSTRUCTIONS
should fit snugly on the Canopy loop after the canopy is installed.
Twist the wires together in the same direction you twist the
wire connector onto the wires.
Fixture Name: Mayfair 7116-SF LC
For Chandelier Light Fixture
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE (Fig 1)
1. Carefully remove the new fixture from the carton and the yellow
bag that holds all parts. Check that all parts are included as
shown in the illustration and parts list.
2. Shut off the power at the circuit breaker and remove old fixture
from ceiling, including the old mounting strap.
3. Thread Nipple(C) into Canopy Loop (F) until snug.
4. Thread other end of the Nipple (C) with Canopy Loop attached
into Mounting Strap (D).
5. Place Lock Washer (B) over end of Nipple (C) protruding
through Mounting Strap (D) and thread Hex Nuts (A) onto Nipple
until tight.
6. Take this mounting strap assembly and mount to ceiling
junction box with junction box Screws (E). Tighten screw securely
with screw driver.
7. Unscrew the Canopy loop collar(H )from the Canopy loop.
Take the canopy and pass over the Canopy loop. approximatly
one half of the canopy loop exterior threads should be exposed.
Adjust until desired height is reached. *the Canopy loop collar
Remove Canopy and Canopy lock collar.
8. Assemble the fixture and have an assistant or secure support
hold the weight of the fixture while you complete the wiring
connections.
9. Thread the fixture wires and ground wire of the assembled
fixture through the canopy loop and nipple and into the outlet box.
CONNECTING THE WIRES (Fig 2)
10. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to
WHITE (or RIBBED).
11. Attach the GROUND wire(GREEN or COPPER) from the
Junction Box and the fixture Ground wire to the green Ground
Screw on the Mounting Bracket (D) or connect both wires
together using the correct size of wire connectors.
NOTE:
Fig. 1
Fig. 2
12. Tuck these wire connections neatly into the Junction Box.
13. Raise Canopy (G) to the ceiling and secure in place by
tightening the Canopy loop collar (H) onto the Canopy Loop (F)
14. Install the light bulbs and glass shade as per the fixture
assembly sheet.
For Customer Service, contact the place of purchase to arrange for replacement parts.
YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX AND
TEST THE FIXTURE.
Loading...