Golden Lighting 7116-ND3 LC User Manual

PARTS & ASSEMBLY SHEET

NOTE: I

NSTALL THE GLASS ASSEMBLY AFTER

THE FIXTURE IS HUNG.

Fixture Name: Mayfair 7116-ND3 LC

This fixture assembled PO:__________ Date: ________

Notice:

damaged, please note onthis sheet and contact the place of purchase to arrange for replacement parts.

PARTS LIST

Canopy Mounting Screws Top loop

1ea ∅5-3/4"*H1-1/2" 2ea 8#32-IP*1" 1ea 1/8-IP*H60mm

Chain Wire connectors Nipple

1ea 6ft ∅3.8 3ea P3 Orange 1ea 1/4-IP*H60mm

Chain connector

2ea ∅5.8*H61mm 1ea ∅1-1/8"*H42mm 1ea W4-1/8"*E1"*H5mm

Cover Nipple

1ea ∅5-1/4"*H130mm 1ea 1/8-IP*H240mm 3ea 3-3/4"*H13-1/4"

Deco Nut

6ea 5/32-IP*H9mm

Arm connector

1ea 2"*H32mm

Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or

Company Name:_______________________Co. Account #:_____________

to be filled out by retailer

Canopy loop
with Collar

Center column -small

1ea ∅1/2"*12mm 1ea ∅1/2"*130mm

Mounting strap

Scroll arm

Center column

Part Needed Quantity

Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments

F

IXTURE ASSEMBLY INSTRUCTIONS

Read and review installation instruction sheet before
assembling the fixture.

Fig 1

ASSEMBLING THE FIXTURE (Fig 1)

1. Gently spread the arms until evenly spaced if arms are
packed closed

2. Thread the Nipple (V) into the hex connector (R).Then the
Cover (T)，Center column (S)，Arm connector (M) and the
small Center column (W) one by one onto the Nipple V)，
use the Top loop (J) to tighten all the pieces.

7116-ND3 LC

For Customer Service, contact the place of purchase to arrange for replacement parts.

7116-PartsInstallation_20110106m.xls

PARTS & ASSEMBLY SHEET

3. Align the arms over the arm connector screws (Z) at base

were attached there.

frame, align the top of Scroll arm (U) over the arm connector

screws (M) at top of Center column and secure in place with

chain connector and attach the other end of the chain to the

12. Make sure the weight of the chandelier will be supported

Fixture Name: Mayfair 7116-ND3 LC

ASSEMBLING THE FIXTURE (Fig 2)

of fixture and secure in place with the Deco nuts (Y) that

4. Tuck the inside of each Scroll arm into the slot in fixture

the Deco nuts (X).

5. Feed the fixture wires through the Top loop (J) and pull
the wires until taut.

6. Then screw the Top Loop (J) to the threaded center
column of Frame (M) until tight.

7. By measuring determine correct number of links needed
for proper hanging height. Use a pair of pliers to open one
link of the Chain (C2) then remove the excess Chain (C2)
and discard it.

8. Use one chain connector(E2) to attach one end of the
chain to the Top loop (D2) and close the chain connector.

Fig 2

9. Feed the fixture wires through the Chain (every three
links) and pull the wires until taut.

10. Slip Canopy loop collar (B2) over the chain, then do the
same with the canopy.

11. When ready to complete the installation Use the other

canopy loop (A2) and close the chain connector.

by the chain-not the electrical wire.
* You may now install the fixture.

Note: Complete these remaining steps after the fixture is
hung.

13. Place the Glass Shades(O) over the Threaded
sockets(P),
secure the Glass Shades (O) by threading by the
Socket Rings (N) until tight.

14. Install the light bulbs in accordance with the fixture's
specifications.

(DO NOT EXCEED MAXIMUM WATTAGE RATING)

Fig 3

For Customer Service, contact the place of purchase to arrange for replacement parts.

7116-PartsInstallation_20110106m.xls