Golden Lighting 7116-BA3 LC User Manual

Company Name:_______________________Co. Account #:_____________

PARTS & ASSEMBLY SHEET

Fixture Name: Mayfair 7116-BA3 LC

This fixture assembled PO:__________ Date: ________

Notice:

are missing or damaged, please note onthis sheet and contact the place of purchase to arrange for
replacement parts.

PARTS LIST

Circular
Mounting Strap

1ea ∅4"*H2mm 2ea 8#32-IP*1" 2ea 5/32-IP*H9mm

Wire connectors Mounting Screws Hex Nut

3ea P3 Orange 2ea 5/32-IP*1-3/4"

Part Needed Quantity

Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments

Please review the parts listing and check for all parts before assembling the fixture. If any parts

to be filled out by retailer

Mounting Screws Deco Nut

2ea 5/32-IP*H3mm

F

IXTURE ASSEMBLY INSTRUCTIONS

Read and review installation instruction sheet, but
do not install before assembling the fixture.

Fig 1

7116-BA3 LC

1. Slide the Glass Shade (J) over Socket ( I) and
secure Glass Shade (J) by threading the Socket
Ring (O) to Socket (I) until tight.

2. Thread the final cap (R) into the square tube (S)
unitl tight.

3. Install the light bulb in accordance with the
fixture's specifications.

(DO NOT EXCEED MAXIMUM WATTAGE RATING

NOTE: I

NSTALL THE GLASS ASSEMBLY AFTER

THE FIXTURE IS HUNG.

For Customer Service, contact the place of purchase to arrange for replacement parts.

7116-PartsInstallation_20110106m.xls

10. Secure the Back Plate (H) against the wall by threading two

INSTALLATION INSTRUCTIONS

Fixture Name: Mayfair 7116-BA3 LC

For Wall Mount Light Fixture

WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.

HANGING THE FIXTURE (Fig 1)

1. Carefully remove the new fixture from the carton and the

yellow bag that holes all your parts. Check that all parts are

included as shown in the illustration and parts list.

2. Shut off power at the circuit breaker and remove the old

fixture from wall, including the old mounting strap.

3. The Mounting Strap (F) contains several pairs of threaded

holes, find the pair of holes that match the holes spacing in

your fixture Back Plate (H) and thread the two Mounting

Screws (D) half way into the Mounting Strap (F) and secure

with Hex Nut (G).

4. Place the Mounting Strap (F)over the Junction Box (A)so the

Mounting Screws (D) are vertical or horizontal, as required by

fixture type.

5. Attach the Mounting Strap (F) to the Junction Box using the

two mounting screws (H)and tighten securely with screw driver.

CONNECTING THE WIRES (Fig 2)

6. Attach the power supply wires to the fixture lead wires by

connecting BLACK to BLACK (or SMOOTH) and WHITE to

WHITE (or RIBBED).

7. Attach the GROUND wire(GREEN or COPPER) from the

Junction Box and the fixture Ground wire to the green Ground

Screw (I) on the Mounting Bracket (F) or connect both wires

together using the correct size of wire connectors.

NOTE:Twist the wires together in the same direction you twist

the wire connector (L) onto the wires.

8. Tuck these wire connections neatly into the Junction Box.

Fig. 1

Fig. 2

FINISHING THE INSTALLATION (Fig 3)

9. After tucking these wire connections neatly into the Junction

Box, place the fixture Back Plate (H) over the two Mounting

Screws (B).

Deco Nuts (P) over the two Mounting Screws (D) until tight as

shown on Fig.1.

11. Install the light bulbs and glass shade as per the fixture

assembly sheet.

YOUR INSTALLATION IS NOW COMPLETE. RETURN

POWER TO THE JUNCTION BOX AND TEST THE FIXTURE.

For Customer Service, contact the place of purchase to arrange for replacement parts.

Fig. 3