Page 1
Part Needed
Quantity
Reason why
( missing, scratched, broken glass, bent, bad finish)
Comments
PARTS & ASSEMBLY SHEET
in the glass. Place the Plastic washer (M) and Metal washer
NOTE: I
Fixture Name: Mayfair 7116-17 LC
This fixture assembled PO:__________ Date: ________
Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or
damaged, please note onthis sheet and contact the place of purchase to arrange for replacement parts.
Company Name:_______________________Co. Account #:_____________
PARTS LIST
to be filled out by retailer
Mounting strap
1ea W3-7/8"*E1"*10mm 1ea 1/8-27-IP*H39mm 3ea P3 Orange
Hex Nut
1ea 1/8-IP*H4mm 2ea ∅3-1/4"*H25mm 2ea 8#32-IP*1"
Nipple Mounting Screws
2ea 1/8-IP*H135mm 2ea 5/32-IP*50
Hex Nut
2ea 5/32-IP*H3mm 1ea 1ea
Part Needed Quantity
F
IXTURE ASSEMBLY INSTRUCTIONS
Read and review installation instruction sheet before
assembling the fixture.
Finial
Bottom cap
Metal washer Plastic washer
Wire connectors
Mounting Screws
7116-17 LC
1. Thread the Nipple (K) into the Ceiling pan (J) coupler
and secure with Hex nut attached.
2. Install the light bulbs in accordance with the fixture's
specifications.
3. Place the Glass shade (L) over the Ceiling pan (J)
allowing the Nipple (K) to protrude through the bottom hole
(N) over the Nipple (K) tighten with Hex Nut (O), slide
Bottom cap (P) over Nipple (K) and tighten with Finial (Q)
*a cover (M) may be included in place of the metal and
plastic washers
(DO NOT EXCEED MAXIMUM WATTAGE RATING!)
NSTALL THE GLASS ASSEMBLY AFTER THE
FIXTURE IS HUNG.
For Customer Service, contact the place of purchase to arrange for replacement parts.
7116-PartsInstallation_20110106m.xls
Fig 1
Page 2
INSTALLATION INSTRUCTIONS
1.Carefully remove the new fixture from the carton and the
Fixture Name: Mayfair 7116-17 LC
For Flush Mount Light Fixture
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE (Fig 1)
yellow bag that holes all your parts. Check that all parts
are included as shown in the illustration and parts list.
2. Shut off power at the circuit breaker and remove the old
fixture from ceiling, including the old mounting strap.
3. Thread the two Fixture Mounting Screws ( G ) into the
pre-drilled Holes in the Mounting Strap (E) spaced the
same distance apart as the holes in the Ceiling Pan.
Secure in place with Hex nuts (F).
4. Attach Mounting Strap ( E ) to the junction box using the
two Mounting Screws ( D )
CONNECTING THE WIRES (Fig 2)
5. Attach the power supply wires to the fixture lead wires
by connecting BLACK to BLACK (or SMOOTH) and
WHITE to WHITE (or RIBBED).
6. Attach the GROUND wire(GREEN or COPPER) from
the Junction Box and the fixture Ground wire to the green
Ground Screw (L) on the Mounting Bracket (E) or connect
both wires together using the correct size of wire
connectors. NOTE: Twist the wires together in the same
direction you twist the wire connector onto the wires.
7. Tuck these wire connections neatly into the Junction
Box.
Fig. 1
Fig. 2
FINISHING THE INSTALLATION (Fig 3)
8. Finish mounting the Ceiling Pan (J) by placing it over
the Mounting Strap (E). Rotate the Pan until the Mounting
screws (G) protrude through the “Keyholes” located in the
bottom of Ceiling Pan (J). Using a screw driver, secure the
Ceiling Pan (J) by screwing Mounting Screws (G) until taut.
9. Install the light bulbs in accordance to the fixture’s
specifications.
10. Install the glass shade as per the assembly
instructions.
YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX AND TEST
THE FIXTURE.
For Customer Service, contact the place of purchase to arrange for replacement parts.
Fig. 3
Loading...