Golden Lighting 6390-M1L WG User Manual
INSTALLATION INSTRUCTIONS
Fixture Name: CORONA DA 6390-M1L WG
For Pendant Light Fixture
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
HANGING THE FIXTURE（Fig.1
）
1. Carefully remove the new fixture from the carton and the yellow
2. Shut off the power at the circ
3. Thread Nipple (C) into Canopy Loop (F) until snug, then thread into
4. Place Lock Washer (B) and Hex Nut (A) over the end of N
5. Take this mounting strap assembly and mount to ceiling junction
6. Unscrew Canopy Loop Collar (H) from the canopy loop. Pass
7. Assemble the fixture and by measuring, determine the correct number
8. Use one Chain Connector (I) to attach one
9. Feed the fixture wires through the chain (every three links) and pull
* Make sure the weight of the fixture will be supported by the
10. Slip Canopy Loop Collar (H) over the chain, then do the same with
11. Thread the fixture wires and ground wire of the assembled fixture
through the canopy loop (F) and nipple(C) into the outlet box.
Fig.1
JUNCTION BOX
(CEILING)
A
B
D C E
F
I G H
CHAIN
I
J
CONNECTING THE WIRES (Fig.2)
12. Attach the power supply wires to the fixture lead wires by
13. Attach the ground wire (GREEN or COPPER) from the junction
correct size of
wire
connectors.
2
NOTE: Twist the wires together in the same direction you
twist the wire connector onto the wires.
14. Tuck these wire connections neatly into the Junction Box.
HOUSE WIRES
BLACK
(Hot)
15. Raise Canopy (G) to the ceiling and secure in place by tightening
16. Install the light bulbs and glass shade as per the fixture assembly
FIXTURE WIRES
SMOOTH
(or Black)
RIBBED
(or White)
BARE COPPER
(or Green)
WHITE
(Neutral)
GREEN
(Ground)
YOUR INSTALLATION IS NOW COMPLETE. TU RN POWER ON AT
TO THE JUNCTION BOX & TEST THE FIXTURE.
For Customer Service, contact the place of purchase to arrange for replacement parts.
C S A0 63 90 1D AL G 1
bag that holds all parts. Check that all parts are included as shown
in the illustration and parts list.
uit breaker and completely remove the old fixture
from the ceiling, including the old mounting strap.
Mounting Strap (D).
ipple (C) and
thread onto the nipple until tight.
box using Junction Box Screws (E). Tighten the screws securely with a screw
driver.
the canopy over the canopy loop leaving some threads exposed.
Adjust Nipple(C) until the desired height is reached. *the Canopy loop
collar should fit snugly. Remove the canopy and canopy lock collar.
of links needed for proper hanging height. Use a pair of pliers to
open one link of chain to remove and discard the excess.
end of the chain to
Top Loop (J) and close the chain connector.
the wires until taut.
chain-not by the electrical wire.
Canopy (G). Attach the chain to the Canopy Loop (F) with
Chain Connector (I).
connecting BLACK to BLACK (or SMOOTH) and WHITE to WHITE (or
RIBBED).
box and the fixture ground wire to the green ground screw on the
Mounting Bracket (B) or connect both wires together using the
Fig.
the Canopy Loop Collar (H) into the Canopy Loop (F).
Sheet.
PARTS & ASSEMBLY SHEET
Fixture Name: CORONA DA 6390-M1L WG
This fixture assembled P O :
Date:
Notice: Please review the parts listing and ch eck for all parts before assembling the fixture. If
any parts are missing or damaged, please note on this sheet and contact the place of
purchase to arrange for replacement parts.
PARTS LIST
Canopy
1ea
Chain
1ea
Link
2ea W20*H45
Company Name:______ ________________ Co A ccount#:__________
below to be filled out by retailer
Hex Nut
2ea NPS-1/4-18
Nipple
1ea NPS 1/4-18*50
Mounting Strap
1ea W103*T2.0
Wire Connectors
3ea Orange
Canopy Loop
1ea NPS 1/4-18*H41
Mounting Screws
2ea G8/32*H32
Part Needed _________ _____________________
Part Needed _________ _____________________
Comments
Quantity ___________ ______________________
Quantity _____________________________ ____
Reason why (missing, scr at ched, broken glass, bent , bad finish)
__________________________________________________________________________
6390-M1L WG
Fig.3
FIXTURE ASSEMBLY INSTRUCTIONS
Read and review installation instruction sheet
before assembling the fixture
1. Place Shade (A) over socket and secure
with Ring (B).
2. Install the bulbs as spe cified. (Bulbs are not included. )
(Do not exceed the maxi mum wattage rating!)
A
B
For Customer Service, contact the place of purchase to arrange for replacement parts.
C S A0 63 90 1D AL G 2
Φ140*H30 ㎜
Φ3.8*6ft
㎜
㎜
㎜
㎜
㎜
Loading...